Orbit 57915 Station Wi-Fi Sprinkler System Controller Instruction Manual

Orbit 57915 Station Wi-Fi Sprinkler System Controller

Contents in the Box

• Wi-Fi Indoor Sprinkler Timer
• Screwdriver
• Mounting Screws and Anchors
• Transformer
• Quick Start Guide
• Conduit Cover

FCC and IC Statement

This device complies with Part 15 of the FCC Rules and Industry Canada license exempt RSS standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the  limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 1-lowever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the fol lowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end user is advised to maintain a distance of 20 cm from the controller and any personnel to ensure compliance with RF exposure regulations.
  This C lass B digital apparatus complies with Canadian ICES-003

The B-hyve™ App

Install the B-hyve™ app on your smart device

You will need a smart device to connect the timer to Wi-Fi.

Note: The app will guide you through initial set up of your sprinkler timer. In addition, there are help icons throughout the app with more information and useful tips.

Specifications

• Transformer ratings

  ---

  • Input:
    **** Australia -24OV AC 50/6o~z 23W
    Europe -23OV AC S0/6oHz 23W
    USA -12OV AC 6OHz 23W

  • Output:
    24V 750 mA

• Timer ratings

  • In put/Output:
    AUS & EU 26V AC 750 mA 50/60 Cycle
    USA -24V AC 750 mA 6OHz

• Timer Temperature Operating Range
  

  • Operating: 32-158° I= (0-70° C)
  • Storage & transport: -4-176° I= (-20-80° C)

• Timer Humidity Operating Range:

  • Operating: 0-80%
  • Storage & transport: 0-90%

• Altitude:
  

  • 6,500′ (2,000 meters)

Installation Class 11
Over Voltage Category 11
This timer works with any standard 24V irrigation solenoid.
The internal fuse is non-replaceable.

Help

If the app and the website don’t have what you’re looking for, please call our technical support line before returning this sprinkler timer to the store.
1-800-488-6156 or 1-801-299-5555
www.orbitonline.com bhyve.orbitonline.com
Acts as a hub for other B-hyve™ products

Timer Instillation

• Select a location
  Choose a location near power and away from direct sunlight, if possible. This location should also have a good Wi-Fi signal. You can check this using a smart phone. (Find a location that has a minimum of two bars)

• Note: If replacing a timer, it is helpful to take a photo of the wires before you remove them from the old timer.

• Mount the timer
  Install a screw (included) into the wall. Use the expanding anchors (included) for plaster, masonry or drywall installations.
  Hang the timer on the installed screw using the keyhole slot. Level the timer and use the second screw in one of the preformed mounting holes to secure the timer.

Connect Valve Wires

• Prepare wire
  Strip½” (13 mm) of insulation from each wire.

• Connect wires
  Attach one wire from each valve to a “Common” (COM) wire and the other wires to a numbered terminal (only one wire per terminal.)
  

Timer Installation-Connecting To Wi-Fi

• Plug in your Orbit® B-hyve TM timer
  Once your 8-hyve™ timer is plugged into the power source, it will automatically look to pair with your smart device. The will begin to blink blue. This indicates that your timer is ready to pair with your smart device. Ensure that your smart device has Bluetooth® turned on.

• Connect to your Orbit® B-hyve™ timer
  Open your B-hyve™ app, create an account or login, and follow the step-by-step process to add and set up your device. The B-hyveTt-1 app will connect to your device and you will, then, be guided to connect to your home Wi-Fi network.

• Connect to your Wi-~i network
  Select your network from the list and enter the password for the network to connect your timer to your Wi-Fi signal. When connected, the will illuminate solid white indicating a successful pairing.
  Note: If you do not see your network name in the list, tap the refresh button in the app. If your network name still does not appear, tap “Advanced” in the app and enter your network name and password. This device will only connect through 2.4 GHz Wi-Fi networks. 5.0 GHz networks are not supported and will not appear in your app.
  

FOR OPTMUM TIMER PERFORMANCE CONNECT TO WIFI TO RECEIVE THE LATEST TIMER UPDATES

Programming And Operation

Programming the timer
The app has help screens and video to assist you with Wi-Fi connections, programming, smart watering and other general questions you may have.

Note: Your programmed schedules are stored both in the app and on the timer.
Watering will continue, if WI-Fi connection is lost.

Manual Operation
All programming and full functionality of the timer are available in the B-hyver1-1 app.
If you have the need, there are some basic operations you can perform directly at your timer.

Quickly press again until desired station appears.
Default watering is 70 min. per station.
CANCEL STATION| Press once to cancel current station.
RAIN DELAV| Set in app; blinks yellow and d appears.
ON/OFF| Hold for 10 sec. until turns white.
HARD RESET| Quickly press 5 times.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>