Orbit 62061Z 1 Outlet Hose Faucet Timer User Guide
- May 15, 2024
- Orbit
Table of Contents
1 OUTLET HOSE
FAUCET TIMER
62061Z 1 Outlet Hose Faucet Timer
Important, please read the following!
| Do not allow the timer to freeze. Freezing
temperatures can permanently damage your timer.
---|---
| Do not use tools on the timer. Hand tighten only. Use of tools may damage
the timer.
| Keep the filter washer clean and in place when using the timer. Replace the
filter if damaged. Debris entering the timer may prevent it from closing.
| For cold water outdoor irrigation use only.
TIMER FEATURES
DIAL—Rotate the dial to customize your watering schedule +/- BUTTONS—Use these
buttons to adjust time and system setup
MANUAL—Press to water manually or to clear programming
RESET—Press to clear all programmingAUTO—Timer waters according to your
customized schedule
SET CLOCK—Set the time of day
START TIME—Select what time you would like to start watering
HOW LONG—Determine how long to water
HOW OFTEN—Choose how often you will water
OFF—Turn off all watering
INSTALLING THE BATTERIES
- Remove the tray on the back of the timer by sliding or pulling it out.
- Insert two AA (1.5V) alkaline batteries (not included) and replace the tray.
NOTE: Firmly replace the battery tray to ensure water resistance and
increase battery life. You will know the battery tray is fully inserted if it
locks in place and does not pull out easily. Used up or dead batteries must be
removed from the timer and disposed of properly. Batteries should be removed
from the timer at the end of the watering season and replaced with new ones at
the beginning of the next watering season. Replace batteries when low battery
icon appears on display. Do not dispose of batteries in fire.
Batteries may explode or leak.
PROGRAMMING THE TIMER
SET CLOCK
- Turn dial to SET CLOCK.
- Using the +/- buttons, set the time of day, including AM and PM. Timer advances faster if button is held down.
- Turn dial to save changes.
START TIME
- Turn dial to START TIME.
- Using the +/- buttons, set your start time, including AM and PM. Timer advances faster if button is held down.
- Turn dial to save changes.
HOW LONG
- Turn dial to HOW LONG.
- Using the +/- buttons, select watering duration from 1 to 240 minutes. Timer advances faster if button is held down.
- Press CLEAR button to reset run time.
- Turn dial to save changes.
HOW OFTEN
-
Turn dial to HOW OFTEN.
-
Using the +/- buttons, set your watering frequency.
You may choose to water every 6 hours, 12 hours, or from 1 to 7 days.
NOTE: 1 is every day, 2 is every other day, etc. -
Turn dial to save changes.
NOTE: For watering programs set up to run more frequently than once every
24 hours, your timer will use the watering interval to determine its first
start time, rather than the start time you have entered for that program.
CONGRATULATIONS!
Your timer is now programmed. Turn your dial to AUTO to allow your timer to
water according to programmed time, station, duration, and frequency.
ADDITIONAL FEATURES
RAIN DELAY
Rain delay allows you to postpone watering for a set period of time. To access the rain delay, follow the steps below.
- With the dial on AUTO, press the + button to select a delay of 24 hrs, 48 hrs, or 72 hrs.
- Screen will flash between clock and hours remaining before programmed cycle resumes.
NOTE: To remove rain delay, turn dial to OFF and then back to AUTO.
MANUAL/HAND WATERING This feature allows you to water without
interrupting your set schedule. To access this feature, follow the steps
below.
- With the dial on AUTO, press the MANUAL button.
- Use the + and – buttons to select watering time, from 1 to 240 minutes. (There will be a slight delay between the time the + button is pressed and when watering begins.)
NOTE: To stop manual watering, turn the dial to OFF and then back to
AUTO.
OFF MODE
Turning the dial to the OFF position at any time during the day will reset the
timer’s internal timing and will clear a RAIN DELAY or MANUAL watering. This
will also cancel all scheduled watering times for the day until the next
programmed START TIME. This means if you turn the dial back to AUTO the timer
will not water until the next day; beginning at your desired programmed START
TIME.
EXAMPLE: You have a 6:00 AM START TIME with HOW OFTEN 6 hour intervals. If you
turn the dial to OFF at 10:00 AM today the timer will not water until tomorrow
at 6:00 AM .
The 12:00 PM, 6:00 PM, and 12:00 AM watering times have been cancelled for the
day.
TROUBLESHOOTING
Water does not come on at desired time.
Check if:
- Clock is set to correct time, including AM and PM.
- Dial is set to “Auto”
- Start time is set to desired time, including AM and PM.
- Rain Delay is on. Clear if necessary.
Timer does not water or has low flow.
Check if:
- Timer is set to AUTO.
- Hose faucet is on.
- Batteries are low.
- Clock is set to correct time, including AM and PM.
- Rain Delay is on. Clear if necessary.
- Filter washer screen is clean.
- Water pressure is above 25 psi.
Water won’t turn off.
Check if:
- HOW LONG is set to desired time.
- HOW OFTEN is set to desired interval hour or day.
Timer is leaking.
Check if:
- Filter washer is in place.
- Filter washer is clean and undamaged.
- Faucet connection is hand tight.
Working water pressure:
- Minimum: 25 psi
- Maximum: 100 psi
Working temperature:
- Maximum: Do not exceed 120°F (48°C)
- Minimum: Keep from freezing
Need Help?
If you encounter a problem, please use the following resources before
returning your Orbit product to the store.
call us
1-800-488-6156 text us
801-797-2319https://www.orbitonline.com/help-center/
or visit us at:
community.orbitonline.com
©2020 Orbit | Utah, USA
orbitonline.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>