Orbit HT25G2ASR Hose Faucet Timer User Guide

: June 2, 2024
: Orbit

Table of Contents

Orbit HT25G2ASR Hose Faucet Timer
Contents
Timer
FCC Statement:
Specifications:
FAQ:
- Q: How do I reset the timer?
- Q: When should I replace the batteries?
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Orbit HT25G2ASR Hose Faucet Timer

USER GUIDE

Model: HT25G2ASR

Insert two new AA Batteries*, the timer is now in pairing mode and will flash a blue light every 5 seconds.
You will also hear two clicks about 6 seconds apart, this is normal and ensures the valve is closed before you turn on the water.
Write down the MAC address: 12 digit alphanumeric code on the bottom of the timer.

Timer MAC Address:–:–:–:–:–:–:

If at any time you need to re-pair or do a factory reset, press the on/off button quickly 5 times

*Batteries are sold separately. Replace batteries when timer flashes a red light every 5 seconds, or when the app notifies you that batteries need replacing.

If you remove or change the batteries you will need to reconnect to Bluetooth® to set the correct time and date.

3). Install the Timer

Your timer is now ready to be used with any product that can be attached to a standard hose faucet.

Do not place the timer in an underground valve box.

4). Turn on Your Water

The water must remain on for the timer to work properly.

Manual Watering

Simply press and hold the on/off button for 5 seconds to activate manual watering.
Need to stop watering, even during a programmed time? Press the on/off button once to stop watering.

Manual Watering

Timer

Range: 150 ft without interference
Pressure Operating Range: 10-100 PSI
Temperature Operating Range: 32°F-158°F (0-70°C)
For Outdoor Use With Cold Water Only
Not For Use With Appliances
Do Not Mix Alkaline, Standard (Carbon-Zinc), or Rechargeable (Nickel Cadmium) Batteries.
Used up or dead batteries must be removed from the timer and disposed of properly.
Do not dispose of batteries in fire.
Batteries may explode or leak.

FCC Statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Warning: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device meets the FCC and IC requirements for RF exposure in public or controlled environments. The end user is advised to maintain a distance 20 cm from the timer and any personnel to ensure compliance with RF exposure regulations.

IC Statement:

This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.