MicroTouch OF-120-PA1 Screen Monitors User Manual

MicroTouch OF-120-PA1 Screen Monitors

About This Document
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of MicroTouchTM a TES Company.

Compliance Information

For FCC (USA)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

For IC (Canada)
CAN ICES-3(B)/NMB-3(B)
For CE (EU)
The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU

Disposal Information
Waste Electrical and Electronic Equipment

• This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
• For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.

Important Safety Instructions

Before using this monitor, please read the user manual thoroughly to help protect against property damage and to ensure your personal safety and the safety of others.
Be sure to observe the following instructions.
For installation or adjustment, please follow the instructions in this manual and refer all servicing to qualified service personnel.

Usage Notice

• Warning
  To prevent the risk of fire or shock hazards, do not expose the product to moisture.

• Warning
  Please do not open or disassemble the product, as this may cause electric shock.

• Warning
  The AC power cord must be connected to an outlet with ground connection.

Precautions
Please follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.

• Do：
  Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.

• Don’t：
  Do not operate the product under the following conditions:
  Extremely hot, cold or humid environment.
  Areas susceptible to excessive dust and dirt.
  Near any appliance generating a strong magnetic field.

Warnings

• To turn off monitor power, press “Power” on the OSD wired remote.

• When turning off the monitor by pressing the POWER button on the remote keypad, the main power of the monitor is not turned off completely.

• To disconnect power completely, remove the power plug from the outlet.

• If any of the following occur, remove the power plug from the outlet immediately:
  the monitor is dropped; the housing is damaged; water is spilled onto or objects dropped inside the monitor.

• Failure to immediately remove the power plug may result in fire or electrical shock. Contact qualified service personnel for inspection.

• If the power cord or plug is damaged or becomes hot, turn the monitor off, make sure the power plug has cooled down and remove the power plug from the outlet.
  If the monitor is still used in this condition, it may cause fire or electrical shock.

• Contact your dealer for replacement.

Warning This product can expose the user to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Installation Tips

No Touch Screen Drivers Required
MicroTouch Touch Monitors are plug and play when connected to Windows 7 or later Windows devices; Kernel 3.2 for most builds of Linux; Android 1.0 and most other modern Operating Systems. If you have a non-Plug and Play operating system, please refer to the Technical Support Section of www.microtouch.com or contact MicroTouch Technical Support to inquire about driver support for your particular operating system.

Things to avoid

• Don’t install in a high-temperature environment. Operating temperature: 0˚C to 40˚C (0˚F to 104˚F), storage temperature -20C – 60C (-4˚F to 140˚F). If the monitor is used in a high temperature environment or near any heat sources, the case and other parts may become distorted or damaged, resulting in overheating or electrical shock.
• Don’t install in a high-humidity environment.
• Operating humidity: 20-90%
• Don’t insert the power plug into anything other than a grounded 100-240V AC outlet.
• Don’t use a damaged power plug or worn outlet.
• The use of extension cords is not recommended.
• The use of the power supply that comes with the MicroTouch product is strongly recommended.
• Don’t place the monitor on an unstable shelf or surface.
• Don’t place objects on the monitor.
• If the monitor is covered or the vents are blocked, the monitor could overheat and cause a fire. Please keep a 10 cm minimum distance between the monitor and the surrounding structures to allow sufficient ventilation.
• Don’t move the monitor when it is connected to the power cord and AV cables.
• When moving the monitor, make sure to remove the power plug and cables from the outlet or source.
• If you encounter a problem during installation, please contact your dealer for assistance. Do not attempt to repair or open the monitor.

Product Overview

This product is a commercial grade standard format open frame touch monitor solution that is particularly well suited for point-of-sales, point-of- information, point-of-service and interactive signage applications. Designed for kiosk installations, it incorporates a rugged, tapered, high-density closed-cell foam gasket surround that compresses on installation, resulting in an attractive sealed finish

Key Features

• Size: 12.1″ TFT LCD
• Resolution: 1024 x 768
• Contrast Ratio: 1000:1
• Aspect Ratio: 4:3
• Brightness: 425 cd/m2
• View Angle: H:178˚, V:178˚
• Video Port: 1 VGA (DB15), 1 HDMI, 1 DP 100 mm x 100 mm VESA mount
• Front is sealed to IP65 standard
• P-cap touch with up to 10 simultaneous touches
• Through-glass touch option allows touch to work through up to 6 mm of cover glass
• Plug and Play: no touch driver installation required for most modern operating systems
• Warranty: 3 years

Unpacking

When unpacking please ensure that all the items in the following Accessories section are included. If any are missing or damaged, please contact the place of purchase for a replacement

Package Contents

Product Setup and Use

• Audio Output
  AUDIO: A standard PC audio jack supplies audio output if a digital video/audio input cable (HDMI or DP) is in use. This audio output is intended to supply a speaker that has amplification and volume control. There is no audio output when a VGA video cable is in use.

• Power Connector
  DC JACK: Power connector (Center pin: + 12 volts DC; Barrel: ground). The outer diameter of the barrel is threaded and the supplied AC to DC converter connector has a threaded nut to secure the cable connection.

• Video Signal Input Connectors
  DP (Display Port): Digital video input.
  HDMI: Digital video input.
  VGA: Analog video input.

• Touch Output Connector
  USB: A type-B port supplies the touch function output.

• OSD Remote Connector
  RJ45: Connnector for the on-screen display (OSD) remote controller, which is used to access the on-screen display menu to select the various options and to turn the monitor on/off.

Configuration and Cable Options
A cable management bracket, outlined in red below, is attached to the back of the monitor:

• It has five cable slots and a central opening below, centered. The bracket, attached by a single screw, can be removed if desired to facilitate cable connections, then reattached. The slots can hold smaller diameter cables; larger diameter cables can be nested within the confinement area.
• Power is supplied by the included AC-to-DC power supply’s fixed 12 volt DC cable connector. The included 1.8 m long power cord is used to connect the monitor’s AC to DC converter to an AC wall outlet. Plug the DC barrel connector into the DC jack on the monitor and tighten the nut to secure the cable. Plug the AC power cable female connector into the receptacle on the power converter, then plug the male connector of the AC cable into a wall outlet.
• Connect the included USB cable from the monitor’s touch output to the computer’s USB Type-A port.
• Connect the OSD wired remote cable to the RJ45 connector.
• DP, HDMI and VGA video cables are included, and any of the three may be used to connect the video signal. Either DP or HDMI is preferred, as they are digital video signals. VGA may, in some cases, require some video setting adjustments. Also, the audio output is not active when VGA is in use.

Turning Monitor On and Off

Connect the monitor to DC power. The monitor should come on within 10 seconds.
If the monitor does not come on within 10 seconds, press the power button on the OSD wired remote. The monitor should power on within 5 seconds.
When the monitor is on, pressing the Power button will open a pop-up that asks, “Do you want to turn off?” If yes, press the Power button again. Another popup says, “Please press the power button again.” Press the Power button again to turn the monitor off.
Note: If there is no video input signal for a preset period, the monitor will automatically go into standby mode. Allow up to 10 seconds for the video to reappear after the signal is reapplied.

On-Screen Display (OSD)
The open frame monitor series requires that the wired remote be connected to make changes to the video or touch settings and to turn the monitor on and off. Controls and options are detailed below.

Locking the OSD and Power button functions

Lock OSD: prevents all the monitor settings from being changed. When this function is activated, all OSD controls and hotkey operations will be disabled except for the Power button.
Lock Power button: Prevents monitor from being turned off by the Power button. The monitor can be powered off by disconnecting from power; it will power on within 10 seconds when power is re-applied. Either or both functions may be locked.

To Lock/Unlock the OSD:

1. Press Menu and Down arrow buttons simultaneously, then release: the Lock menu appears:
2. “OSD key” is highlighted.
3. Press Select.
4. Use Up/Down buttons to select Yes (to lock) or No.
5. Press Select.
6. The menu will go away and the setting will take effect immediately.
7. If the OSD is locked, pressing any OSD button except power will pop up the Lock menu again with OSD highlighted – press select and proceed as above to unlock it.

To Lock/Unlock the Power button:

1. Press Menu and Down arrow buttons simultaneously, then release: the Lock menu appears:
2. Use the UP/Down buttons to highlight “Power key”.
3. Press Select.
4. Use Up/Down buttons to select Yes (to lock) or No.
5. Press Select.
6. The menu will go away and the setting will take effect immediately.
7. If the power button is pressed when it is locked, the Lock menu will pop up. Use the Up/Down buttons to select Power key, press select and proceed as above to unlock it.

Using the OSD Menus

• Navigating through the Menu System
• With the power on, press MENU and the on-screen menu will pop up.
• Within the menu, use and SELECT to navigate through the menus and adjust options.
• Press MENU to return to the previous menu or exit the OSD menu
• The OSD menu will automatically close if left idle for a pre-set time.

Picture Menu
This menu is used for making common image adjustments. Note that some of the adjustments may be grayed out, indicating that they are not selectable. This indicates the use of a digital video input signal (DP, HDMI or USB Type-C). These selections are fixed/not adjustable for digital video signals. The VGA video signal (because it is analog) may require all adjustments, so they are all selectable when VGA is being used.

• Contrast
  Increases or decreases the contrast of the picture. Press  or , select the desired level, and then press SELECT.
  Range: 0-100

• Brightness
  Increases or decreases the brightness of the picture. Press  or , select the desired level, and then press SELECT.

• Range: 0-100 H-Position
  Adjust the horizontal position of the picture. Press  or  to select the desired level, and then press SELECT. Selectable only when VGA input is in use.

• Range: 0-100 V-Position
  Adjust the vertical position of the picture. Press  or  to select the desired level, and then press SELECT. Selectable only when VGA input is in use.

• Range: 0-100 Phase
  Adjust the pixel phase of the picture. Press  or  to select the desired level, and then press SELECT. Selectable only when VGA input is in use.

• Range: 0-100 Clock
  Adjust the horizontal dot of the picture. Press  or  to select the desired level, and then press SELECT. Selectable only when VGA input is in use.

• Range: 0-100 Auto Adjust
  Adjust and fine-tune the image to full screen automatically. Selectable only when VGA input is in use.

Advanced Menu
This menu is used to adjust color temperature and image sharpness.

• Color Temp
  Select the color temperature
  Options: 5500K, 6500K, 7500K, 9300K, User

• Red
  Adjust the amount of red in color content
  Range: 0-100

• Green
  Adjust the amount of green in color content
  Range: 0-100

• Blue
  Adjust the amount of blue in color content
  Range: 0-100

• Sharpness
  Adjusts the definition of the picture. Press select the desired level, and then press SELECT. Selectable only when VGA input is in use.
  Range: 0-50

OSD Menu
This menu is used to make set-up adjustments to the OSD itself, as well as other on-screen messages

• OSD Timeout
  Adjusts the time in seconds before the OSD menu disappears after no usage.
  Range: 0-60 sec OSD Position

• Selects the OSD Position (center or corners). Press to select the rotation.
  Options: Top Left, Bottom Left, Top Right, Bottom Right, Center OSD H-Position

• Adjusts the horizontal position of the OSD menu. Press to select the desired horizontal position, then press SELECT.
  Range: 0-100 OSD V-Position

• Adjust the vertical position of the OSD menu. Press to select the desired vertical position, then press SELECT.
  Range: 0-100

• Touch Switch
  Adjusts the sensitivity of the touch function. Press to select any of the three sensitivities, then press SELECT.
  Normal: Standard touch sensitivity, up to 10 simultaneous touch points.

• Glove: Increases touch sensitivity for use with or without cotton or similar gloves; up to 10 simultaneous touch points.
  Through-Glass: Increased touch sensitivity to allow touch operation to project through up to 6 mm of standard window glass. This mode is restricted to no more than 2 simultaneous touch points.
  Range: N/A

Option Menu
This menu is used select or display various functions.

• Reset
  Restore the factory default settings.
  Options: Yes, No

• Language
  Select the OSD language
  Options: English, French, Deutsch, Italian, Spanish, Japanese, Traditional Chinese and Simplified Chinese

• Source Select
  Select the Video Input Source
  Options: Auto, VGA, HDMI, DP

• Display Mode
  Display the current video source and resolution information.

• Factory
  Enter factory mode
  This is only for maintenance service only. Do not use this function

OSD Default Settings
Note: N/A applies when a digital video input (DP or HDMI) is in use

Picture

| Contrast| 50
Brightness| 100
H-Positon| N/A
V-Positon| N/A
Phase| N/A
Clock| N/A
Auto Adjust| N/A
Advanced| Color Temp| User
Sharpness| 50

OSD

| OSD Timeout| 15
OSD Positon| User
OSD H-Positon| 50
OSD V-Positon| 50
Touch Switch| Normal

Option

| Reset| N/A
OSD Language| English
Source Select| Auto
Display Mode| N/A
Factory| N/A

Mounting options

The monitor is commonly mounted to a cross bar in an enclosure, the crossbar having a 100mm x 100mm standard VESA mount hole pattern. It may also be panel mounted using the included bracketry. A tapered foam surround gasket, thinner at the rear than at the front, compresses as the monitor is pushed into the front of the panel opening. The correct panel opening dimensions are 519 mm x 314 mm with corner radii of 9.5 mm (all dimensions plus or minus 0.2 mm).

VESA Mount
The monitor has an integral VESA standard mount pattern that conforms to the “VESA Flat Display Mounting Interface Standard” which defines a physical mounting interface and corresponds to the standards for monitor mounting devices.

Warning
Please use the correct screws! The distance between the back cover surface and the bottom of the screw hole is 8 mm. Please use four M4 diameter screws with 8 mm length to mount the monitor

Bracket Mounting

The included MicroTouch bracket kit OF-BRKT-22B can be used to flush-mount the monitor in a panel. The kit includes four smaller monitor brackets and four larger slotted panel-mount brackets. Two of the smaller brackets are mounted to the sides of the monitor and the other two of the smaller brackets are mounted to the top and bottom of the monitor using eight of the sixteen included screws. The pre-tapped M4 holes are on the back edges of the monitor.
The four larger slotted brackets are then mounted to the rear of the panel, at the sides and at the top and bottom of the opening. The monitor is then pushed into the opening from the front, compressing the tapered foam surrounding gasket, and each bracket pair is joined from the rear using the remaining eight screws included in the bracket kit. Slots in the panel-mounted brackets allow adjustment to slide the monitor into position flush with the front of the panel and the screws are then tightened to secure the monitor in place.
The monitor may be mounted into a panel in any of three ways: 1. incorporating pressed-in threaded studs (PEM® studs) in the back of the panel 2. if the panel is sufficiently thick, M4 threaded holes may be incorporated 3. clearance holes for M4 screws may be used The methods use different hole spacings, as detailed in the drawings on the following page. Note that, because of the bezel-less design, the screw locations are outside the panel opening. If the fasteners are to be invisible, either the pressed-in stud or threaded hole method should be used. Flat head (flush with panel) screws may be used to improve the appearance if thru-hole screws are to be used.

Press-in threaded M4 Stud Method
The studs should be pressed into the back of the panel using the spacing below. The brackets slip onto the studs using the through-holes in the brackets. Nuts (not included/customer supplied) secure the brackets to the back of the panel.

Threaded M4 holes in thick panel method
Holes are drilled into the back of the panel, stopping short of the panel front to preserve invisibility. The holes should be tapped for M4 screws. Customer-provided M4 screws of the proper length go through the through-holes in the bracket, then screw into the threaded holes in the panel. The spacing is the same as for pressed-in studs

M4 Through-hole method
Countersunk holes are drilled into the front of the panel at the spacing shown below. Customer-provided flat head M4 screws pass through the front of the panel and thread into the tapped holes in the panel bracket. The heads of the screws will be visible on the front of the panel, but the screw heads will be flush with the panel if the holes are properly drilled.

Specifications and Dimensions

Specifications

LCD Panel

| Size| 12.1” TFT LCD
Resolution| 1024 x 768
Brightness (typical)| 425 cd/m2
Contrast Ratio (typical)| 1000:1
Viewing Angle (typical)| Horizontal: 178 degrees; Vertical: 178 degrees
Touch Screen| Touch Type| P-CAP
Simultaneous touch points| Up to 10 with optional through-glass capability

Video

| ****

Type

| DisplayPort 1.2a

HDMI 1.3 (Compatible with HDMI 1.4) VGA

Power

| AC to DC Converter Input| AC 100V – 240V (50/60Hz), 60W max
AC to DC Converter Output| 12VDC, 3A max
Monitor On| 15W typical, 18W max (1.25A typ, 1.5A max)
Power Saving| Sleep mode: ≤ 1.5W; Off: ≤ 0.3W

Size and Weight

| Dimensions (W x H x D)| 308.3 mm x 247.8 mm x 47.3 mm
12.14 in x 9.76 in x 1.87 in
Net Weight| 4 kg

8.82 lb

VESA Mount| 100 mm x 100 mm

Environment

| Compliance| CE, FCC, LVD, RoHS
Front seal| IP65
Operating Temperature| 0°C – 40°C
Storage Temperature| -20°C – 60°C
Operating Humidity| 20% – 90% RH, non-condensing

Supported Timings

Mode

| ****

Resolution

| ****

H-Freq. (KHz)

| ****

Bandwidth (MHz)

| Polarity
---|---|---|---|---
H| V
1| 640 x 480 @ 60Hz| 31.47| 25.175| –| –
2| 800 x 600 @ 60Hz| 37.88| 40| +| +
3| 1024 x 768 @ 60Hz| 48.36| 65| –| –
4| 1280 x 1024 @ 60Hz| 49.702| 83.5| –| +

Dimensions

Front view

Side View

Rear View

Cleaning

Turn off the product and disconnect from AC power before cleaning. Turning the product off protects against accidental touch selections that could cause problems or hazardous results. Disconnecting power protects against hazardous interaction between accidental liquid entry and electricity. To clean the case, dampen a clean cloth lightly with water and a mild detergent and wipe gently. Use a soft, dry cloth to clean areas that have ventilation openings to avoid getting any liquid or moisture inside. If liquid does get inside, do not use the product until it has been inspected and tested by a qualified service technician. To clean the touch screen, apply a glass cleaning solution to a soft cloth and wipe the screen clean. To ensure that liquid does not enter the product, do not spray cleaning solution directly onto the touch screen or any other part. Do not use volatile solvents, waxes or any abrasive cleaners on any part of the product

Solutions to Common Problems

• No image on monitor
  Check that the video signal source device is turned on.
  Check that the selected video input signal matches the video connection.
  The monitor or computer may be in SLEEP mode. Press any key/move the mouse/touch the touchscreen and wait a few seconds to see if the image appears.
  Check that the DC power connector is fully seated.
  Check that the AC cable is securely connected to the wall outlet and to the AC to DC converter.
  Make sure the MicroTouch power converter is being used.
  Try another MicroTouch-approved power converter if possible.

• Monitor display is dim.
  Use the OSD controls to increase the brightness.
  Use the OSD controls to increase the contrast.

• Can only adjust Contrast and Brightness using OSD, cannot select Position, AutoAdjust, etc.
  Monitor is connected to a digital video signal source (HDMI or DP), which does not need such adjustments. Only analog (VGA) video signal needs these adjustments.

• Monitor displays the “Out of Range” message.
  This message will only occur when using the VGA video signal input; use either the HDMI or Display Port video signal input if your signal source equipment supports either of those.
  Reduce the resolution to a resolution the monitor supports – see the Supported Timings chart in the Specifications and Dimensions section of this manual.

• Monitor display image looks strange.
  Try the Auto Adjust function in the OSD (only available when using the VGA video signal input).
  Adjust your computer’s resolution/timing mode to be within the allowable timing ranges specified for your touch monitor (see section above).

• Touch functionality doesn’t work or works incorrectly.
  Make sure the USB cable is properly connected.
  Fully remove any protective sheets from the screen, then cycle power Off/On.
  Ensure that the monitor is in an upright position with nothing touching the screen, then cycle power Off/On.
  Legacy operating systems, prior to circa 2007, may require drivers to support Touch Devices. Please contact MicroTouch Technical Support.

• Neither the OSD nor power buttons respond when pressed.
  See the Lock/Unlock section to check if both functions are locked.
  If the wired OSD remote is in use, make sure it is securely connected

Warranty Information

Except as otherwise stated herein, or in an order acknowledgment delivered to Buyer, Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship. The warranty for the touchscreen display and their components is three years. Seller makes no warranty regarding the model life of components. Seller’s suppliers may at any time and from time to time make changes in the components delivered as Products or components. Buyer shall notify Seller in writing promptly (and in no case later than 30 days after discovery) of the failure of any Product to conform to the warranty set forth above; shall describe in commercially reasonable detail in such notice the symptoms associated with such failure; and shall provide to Seller the opportunity to inspect such Products as installed, if possible. The notice must be received by Seller during the Warranty Period for such product, unless otherwise directed in writing by the Seller. Within thirty days after submitting such notice, Buyer shall package the allegedly defective Product in its original shipping carton(s) or a functional equivalent and shall ship to Seller at Buyer’s expense and risk. Within a reasonable time after receipt of the allegedly defective Product and verification by Seller that the Product fails to meet the warranty set forth above, Seller shall correct such failure by, at Seller’s options, either (i)modifying or repairing the Product or (ii) replacing the Product. Such modification, repair, or replacement and the return shipment of the Product with minimum insurance to Buyer shall be at Seller’s expense. Buyer shall bear the risk of loss or damage in transit and may insure the Product. Buyer shall reimburse Seller for transportation cost incurred for Product returned but not found by Seller to be defective. Modification or repair, of Products may, at Seller’s option, take place either at Seller’s facilities or at Buyer’s premises. If Seller is unable to modify, repair, or replace a Product to conform to the warranty set forth above, then Seller shall, at Seller’s option, either refund to Buyer or credit to Buyer’s account the purchase price of the Product less depreciation calculated on a straight-line basis over Seller’s stated Warranty Period. These remedies shall be the buyer’s exclusive remedies for breach of warranty. Except for the express warranty set forth above, seller grants no other warranties, express or implied by statute or otherwise, regarding the products, their fitness for any purpose, their quality, their merchantability, their non-infringement, or otherwise. No employee of Seller or any other party is authorized to make any warranty for the goods other than the warranty set forth herein. Seller’s liability under the warranty shall be limited to a refund of the purchase price of the product. In no event shall Seller be liable for the cost of procurement or installation of substitute goods by Buyer or for any special, consequential, indirect, or incidental damages. Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless from all liability relating to (i) assessing the suitability for Buyer’s intended use of the Products and of any system design or drawing and (ii) determining the compliance of Buyer’s use of the Products with applicable laws, regulations, codes, and standards. Buyer retains and accepts full responsibility for all warranty and other claims relating to or arising from Buyer’s products, which include or incorporate Products or components manufactured or supplied by Seller. Buyer is solely responsible for any and all representations and warranties regarding the Products made or authorized by Buyer. Buyer will indemnify Seller and hold Seller harmless from any liability, claims, loss, cost, or expenses (including reasonable attorney’s fees) attributable to Buyer’s products or representations or warranties concerning same.

RoHS Declaration

Equipment name：Touch LCD Monitor     Type designation (Type) ： OF-120P-A1

Component

| ****

Restricted substances and their chemical symbols

Lead (Pb)

| ****

Mercury (Hg)

| ****

Cadmium (Cd)

| ****

Hexavalent chromium

(Cr+6)

| ****

Polybrominated biphenyls

(PBB)

| ****

Polybrominated diphenyl ethers (PBDE)

Plastic Parts| ○| ○| ○| ○| ○| ○
Metal Parts| －| ○| ○| ○| ○| ○
Cable components| －| ○| ○| ○| ○| ○
LCD Panel| －| ○| ○| ○| ○| ○
Touch Panel| －| ○| ○| ○| ○| ○
PCBA| －| ○| ○| ○| ○| ○
Software| ○| ○| ○| ○| ○| ○
Notes

〝○〞indicates that the percentage of the restricted substance does not exceed the permissible limit.

〝−〞indicates that the restricted substance is exempt.

www.MicroTouch.com www.usorders@microtouch.com
TES AMERICA LLC | 215 Central Avenue, Holland, MI 49423 | 616-786-5353
The information presented in this document is intended as general information about MicroTouch products and is subject to change. Product specifications and warranties will be governed by TES America, LLC. Standard terms and conditions of sale. Products are subject to availability. Copyright © 2022 TES America, LLC. All rights reserved. Android is a trademark of Google LLC. Windows is a trademark of Microsoft Corporation in the United States and other countries.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>