MicroTouch SK-170P-A1 Slimline Kiosk Touch Monitor User Manual

MicroTouch SK-170P-A1 Slimline Kiosk Touch Monitor

Important Safety Instructions

• Before using this monitor, please read the user manual thoroughly to help protect against property damage and to ensure your personal safety and the safety of others.
• Be sure to observe the following instructions.
• For installation or adjustment, please follow the instructions in this manual and refer all servicing to qualified service personnel.

Usage Notice

Warning
To prevent the risk of fire or shock hazards, do not expose the product to moisture.

Warning
Please do not open or disassemble the product, as this may cause an electric shock.

Warning
The AC power cord must be connected to an outlet with a ground connection.

Precautions
Please follow all warnings, precautions, and maintenance as recommended in this user’s manual to maximize the life of your unit.

Do：
Disconnect the power plug from the AC outlet if the product is not going to be used for an extended period.

Don’t：

• Do not operate the product under the following conditions:
• Extremely hot, cold or humid environment.
• Areas are susceptible to excessive dust and dirt.
• Near any appliance generates a strong magnetic field.

Warnings

• To turn off monitor power, press “Power” on the OSD (On-Screen Display) wired remote.
• When turning off the monitor by pressing the POWER button on the remote keypad, the main power of the monitor is not turned off completely.
• To disconnect the power completely, remove the power plug from the outlet.
• If any of the following occur, remove the power plug from the outlet immediately: the monitor is dropped; the housing is damaged; water is spilled onto or objects dropped inside the monitor.
• Failure to immediately remove the power plug may result in fire or electrical shock. Contact qualified service personnel for inspection.
• If the power cord or plug is damaged or becomes hot, turn the monitor off, make sure the power plug has cooled down and remove the power plug from the outlet.
• If the monitor is still used in this condition, it may cause fire or electrical shock.
• Contact your dealer for replacement.

Warning This product can expose the user to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Installation Tips

No Touch Screen Drivers Required
MicroTouch Touch Monitors are plug-and-play when connected to Windows 7 or later Windows devices; Kernel 3.2 for most builds of Linux; Android 1.0 and most other modern Operating Systems. If you have a non-Plug and Play operating system, please refer to the Technical Support Section of www.microtouch.com or contact MicroTouch Technical Support to inquire about driver support for your particular operating system.

Things to avoid
Don’t install in a high-temperature environment. Operating temperature: 0˚C to 40˚C (0˚F to 104˚F), storage temperature -20C – 60C (-4˚F to 140˚F). If the monitor is used in a high-temperature environment or near any heat sources, the case and other parts may become distorted or damaged, resulting in overheating or electrical shock.

• Don’t install in a high-humidity environment.
• Operating humidity: 20-90%
• Don’t insert the power plug into anything other than a grounded 100-240V AC outlet.
• Don’t use a damaged power plug or worn outlet.
• The use of extension cords is not recommended.
• The use of the power supply that comes with the MicroTouch product is strongly recommended.
• Don’t place the monitor on an unstable shelf or surface.
• Don’t place objects on the monitor.
• If the monitor is covered or the vents are blocked, the monitor could overheat and cause a fire. Please keep a 10 cm minimum distance between the monitor and the surrounding structures to allow sufficient ventilation.
• Don’t move the monitor when it is connected to the power cord and AV cables.
• When moving the monitor, make sure to remove the power plug and cables from the outlet or source.
• If you encounter a problem during installation, please contact your dealer for assistance. Do not attempt to repair or open the monitor.

Product Overview

This Slimline Kiosk monitor is a commercial-grade standard format touchscreen solution that is ideal for a wide range of public information and interaction applications that require high quality and reliability in high use environments.

Key Features

• Size: 17″ TFT LCD
• Resolution: 1280 x 1024
• Contrast Ratio: 1000:1
• Aspect Ratio: 5:4
• Brightness: 225 nits
• View Angle: H:170˚,
• V:160˚ Video Port: 1
• VGA (DB15), 1 HDMI, 1 DP
• 100 mm x 100 mm VESA mount
• The front is sealed to IP65 standard
• P-cap touch with up to 10 simultaneous touches
• Plug and Play: no touch driver installation is required for most modern operating systems
• Warranty: 3 years

Unpacking
When unpacking please ensure that all the items in the following Accessories section are included. If any are missing or damaged, please contact the place of purchase for a replacement.

Package Contents

Product Setup and Use

Power Connector
12 VDC: Power connector (Center pin: + 12 volts DC; Barrel: ground).

Video Signal Input Connectors

• DP (Display Port): Digital video input.
• HDMI: Digital video input.
• VGA: Analog video input.

Optional OSD Remote Connector
RJ11: Connector for the on-screen display (OSD) remote controller, which is used to access the on-screen display menu to select the various options, and to turn the monitor on/off.

Touch Output Connector
USB 2.0 is the touch function output.

Configuration and Cable Options
Power is supplied by the included AC-to-DC power supply’s fixed 12-volt DC cable connector. The included 1.8 m long power cord is used to connect the monitor’s AC to DC converter to an AC wall outlet. Plug the DC barrel connector into the DC jack on the monitor. Plug the AC power cable connector into the receptacle on the power converter, then plug the male connector of the AC cable into a wall outlet.

Connect the included USB cable from the monitor’s touch output to the computer.

DP, HDMI, and VGA video cables are included, and any of the three may be used to connect the video signal. Either DP or HDMI is preferred, as they are digital video signals. VGA may, in some cases, require some video setting adjustments.

Turning the Monitor On and Off

• Turning the monitor On
• Connect the monitor to DC power.
• If the monitor does not come on within a few seconds, press the power button on the OSD keypad, outlined in red below, or the optional OSD wired remote.

When the monitor is on, pressing the Power button will open a pop-up that asks if the monitor is to be turned off. If yes, press the Power button again. Press the Power button one more time in response to the final popup to turn the monitor off.
Note: If there is no video input signal for a preset period, the monitor will automatically go into standby mode.

On-Screen Display (OSD)
The Slimline Kiosk monitor series provides OSD controls on the right rear side of the monitor, as viewed from the front, as outlined in red below. An optional wired OSD remote is also available.

Locking the OSD and Power button functions

• Lock OSD : prevents all the monitor settings from being changed. When this function is activated, all OSD controls and hotkey operations will be disabled except for the Power button.
• Lock Power button: Prevents monitor from being turned off by the Power button. The monitor will power on automatically when power is applied.
  Either or both functions may be locked.

To Lock/Unlock the OSD/Power buttons:

1. Press and hold Select for 5 seconds until the Lock menu appears, showing OSD “Active” (not locked) or “Inactive” (locked) and Power Active or Inactive.
2. Use the UP/Down buttons to highlight OSD or Power.
3. Press Select.
4. Use Up/Down buttons to select Yes or No (to change the setting).
5. Press Select.
6. The menu will go away after a few seconds and the selected item will lock if unlocked or unlock if locked, or Menu can be pressed to exit and take effect immediately.

Using the OSD Menus

• Navigating through the Menu System
• With the power on, press MENU, and the on-screen menu will pop up.
• Within the menu, use and SELECT to navigate through the menus and adjust options. Press MENU to return to the previous menu or exit the OSD menu
• The OSD menu will automatically close if left idle for a pre-set time.

Picture Menu
This menu is used for making common image adjustments. Note that some of the adjustments may be grayed out, indicating that they are not selectable. This indicates the use of a digital video input signal (DP, HDMI or USB Type-C). These selections are fixed/not adjustable for digital video signals. The VGA video signal (because it is analog) may require all adjustments, so they are all selectable when VGA is being used.

Contrast: Increases or decreases the contrast of the picture. Press , select the desired level, and then press SELECT.
Range: 0-100

Brightness: Increases or decreases the brightness of the picture. Press , select the desired level, and then press SELECT.
Range: 0-100

H-Position: Adjust the horizontal position of the picture. Press to select the desired level, and then press SELECT. Selectable only when VGA input is in use.
Range: 0-100

V-Position: Adjust the vertical position of the picture. Press to select the desired level, and then press SELECT. Selectable only when VGA input is in use.
Range: 0-100

Phase: Adjust the pixel phase of the picture. Press to select the desired level, and then press SELECT. Selectable only when VGA input is in use.
Range: 0-100

Clock: Adjust the horizontal dot of the picture. Press to select the desired level, and then press SELECT. Selectable only when VGA input is in use.
Range: 0-100

Auto Adjust: Adjust and fine-tune the image to the full screen automatically. Selectable only when VGA input is in use.

Advanced Menu
This menu is used to adjust color temperature and image sharpness.

Color Temp
Select the color temperature
Options: 5500K, 6500K, 7500K, 9300K, User

Red
Adjust the amount of red in color content
Range: 0-100

Green
Adjust the amount of green in color content
Range : 0-100

Blue
Adjust the amount of blue in color content
Range: 0-100

Sharpness
Adjusts the definition of the picture. Press , select the desired level, and then press SELECT. Selectable only when VGA input is in use.
Range: 0-50

OSD Menu
This menu is used to make set-up adjustments to the OSD itself, as well as other on-screen messages.

OSD Timeout
Adjusts the time in seconds before the OSD menu disappears after no usage.
Range: 0-60 sec OSD

Position
Select the OSD Position (center or corners). Press to selects the rotation.
Options : Top Left, Bottom Left, Top Right, Bottom Right, Center

OSD H-Position
Adjust the horizontal position of the OSD menu. Press to select the desired horizontal position, then press SELECT.
Range: 0-100

OSD V-Position
Adjust the vertical position of the OSD menu. Press to select the desired vertical position, then press SELECT.
Range: 0-100

Option Menu
This menu is used select or display various functions.

Reset: Restore the factory default settings.
Options: Yes, No

Language
Select the OSD language
Options: English, French, Deutsch, Italian, Spanish, Japanese, Traditional Chinese and Simplified Chinese

Source Select
Select the Video Input Source
Options: Auto, VGA, HDMI, DP

Display Mode
Display the current video source and resolution information.

Factory
Enter factory mode
This is only for maintenance service. Do not use this function.

OSD Default Settings
Note: N/A applies when a digital video input (DP or HDMI) is in use

Picture

| Contrast| 50
Brightness| 100
H-Positon| N/A
V-Positon| N/A
Phase| N/A
Clock| N/A
Auto Adjust| N/A
Advanced| Color Temp| User
Sharpness| 50

OSD

| OSD Timeout| 15
OSD Positon| User
OSD H-Positon| 50
OSD V-Positon| 50

Option

| Reset| N/A
OSD Language| English
Source Select| Auto
Display Mode| N/A
Factory| N/A

Mounting options
The monitor may be mounted to a stand or other device that has a 100mm x 100mm standard VESA mount hole pattern. It may also be panel mounted.

VESA Mount
The monitor has an integral VESA standard mount pattern that conforms to the “VESA Flat Display Mounting Interface Standard” which defines a physical mounting interface and corresponds to the standards for monitor mounting devices.

Warning
Please use the correct screws! The distance between the back cover surface and the bottom of the screw hole is 8 mm. Please use four M4 diameter screws with 8 mm length to mount the monitor.

Mise en garde
Veuillez utilizer les vis correcte! La distance entre la surface du capot arrière et le fond du trou de vis est de 8 mm. Veuillez uti lizer quatre vis de diamètre M4 d’une longueur de 8 mm pour mounter le moniteur.

Stand Mount
This monitor may be mounted to a stand using the VESA mount pattern. A MicroTouch optional stand is recommended – see the Accessories section of the MicroTouch web site.

Panel Mount
The optional MicroTouch bracket kit BRKT-KIT-A2 can be used to flush-mount the monitor in a panel. Two brackets are mounted to the rear of the panel and two brackets are mounted to the sides or top and bottom of the monitor using the pre-tapped M4 holes. The monitor is then slid into the opening and the bracket pairs are joined using the screws included in the bracket kit. Slots in the panel brackets allow adjustment to slide the monitor into position flush with the front of the panel and the screws are then tightened to secure the monitor in place.

Bracket Detail
Top or Bottom View

3D View 1

3D View 2

Side Hole Detail

Top/Bottom Hole Detail

Specifications and Dimensions

Specifications

LCD Panel

| Size| 17” TFT LCD
Resolution| 1280 x 1024
Brightness (typical)| 225 cd/m2
Contrast Ratio (typical)| 1000
Number of Colors| 16.7 million
Viewing Angle (typical)| Horizontal: 170 degrees; Vertical: 160 degrees
Touch Screen| Touch Type| P-CAP
Simultaneous touch points| Up to 10

Video

| ****

Type

| DisplayPort 1.2a

HDMI 1.3 (Compatible with HDMI 1.4) VGA

Power

| AC Adapter Input| AC 100V – 240V (50/60Hz), 60W max
AC Adapter Output| 12VDC, 5A max
Monitor On| 15W typical, 20W max (1.25A typ, 1.66A max)
Power Saving| Sleep mode: ≤ 1W; Off: ≤ 0.5W

Size and Weight

| Dimensions (W x H x D)

Without Stand

| 369 mm x 307 mm x 47.3 mm
14.53 in x 12.09 in x 1.87 in
Dimensions (W x H x D)

With IS-000-A1 Stand

| 369 mm x 384.4 mm x 219 mm
14.53 in x 15.14 in x 8.63 in
Net Weight| 3.6 kg without stand, 5.9 kg with IS-000-A1 stand

7.94 lb without stand, 13.01 lb with IS-000-A1 stand

VESA Mount| 100 mm x 100 mm

Environment

| Compliance| CE, FCC, LVD, RoHS
Front seal| IP65
Operating Temperature| 0°C – 40°C
Storage Temperature| -20°C – 60°C
Operating Humidity| 20% – 90% RH, non-condensing

Supported Timings

Mode

| ****

Resolution

| ****

H-Freq. (KHz)

| Bandwidth (MHz)| Polarity
---|---|---|---|---
H| V
1| 720 x 400  @ 70Hz| 31.47| 28.322| –| +
2| 640 x 480  @ 60Hz| 31.47| 25.175| –| –
3| 640 x 480  @ 66Hz| 35| 32.24| –| –
4| 640 x 480  @ 72Hz| 37.86| 31.5| –| –
5| 640 x 480  @ 75Hz| 37.5| 31.5| –| –
6| 800 x 600  @ 56Hz| 35.16| 36| +| +
7| 800 x 600  @ 60Hz| 37.88| 40| +| +
8| 800 x 600  @ 75Hz| 46.88| 49.5| +| +
9| 800 x 600  @ 72Hz| 48.08| 50| +| +
10| 832 x 624  @ 75Hz| 49.72| 57.283| –| –
11| 1024 x 768  @ 60Hz| 48.36| 65| –| –
12| 1024 x 768  @ 70Hz| 56.48| 75| –| –
13| 1024 x 768  @ 75Hz| 60.02| 78.75| +| +
14| 1280 x 1024 @ 60Hz| 64| 108| +| +
15| 1280 x 1024 @ 75Hz| 80| 135| +| +
16| 1152 x 864  @ 75Hz| 67.5| 108| +| +
17| 1280 x 960  @ 60Hz| 60| 108| +| +

Dimensions (without stand)

Front view

Side View

Rear View

Side View

Appendix

Cleaning
Turn off the product and disconnect from AC power before cleaning. Turning the product off protects against accidental touch selections that could cause problems or hazardous results. Disconnecting power protects against hazardous interaction between accidental liquid entry and electricity.

To clean the case, dampen a clean cloth lightly with water and a mild detergent and wipe gently. Use a soft, dry cloth to clean areas that have ventilation openings to avoid getting any liquid or moisture inside. If liquid does get inside, do not use the product until it has been inspected and tested by a qualified service technician.

• To clean the touch screen, apply a glass cleaning solution to a soft cloth and wipe the screen clean.
• To ensure that liquid does not enter the product, do not spray the cleaning solution directly onto the touch screen or any other part.
• Do not use volatile solvents, waxes, or any abrasive cleaners on any part of the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>