Ustellar UT88868 Exterior RGB 100W LED Flood Light User Guide

Ustellar UT88868 Exterior RGB 100W LED Flood Light

Product Information

Specifications

• Model: UT88868
• Wattage: 100W
• Color Temperature: 5000K
• Max Luminous Flux: 10000lm
• Input Voltage: AC120V
• Frequency: 50/60Hz
• Waterproof Rating: IPX1
• Beam Angle: 1 degree
• Controlled By: D2D Sensor & IR Receiver
• Battery for Controller: Yes
• Life Expectancy: Not specified
• Working Temperature: Not specified

Product Usage Instructions

Warning

• Please check if the light and the parts are intact before installation.
• Make sure to cut off power before installation.
• Please do not place this light in corrosive conditions.
• If there is any damage to the cord, please cut off the power and stop using it immediately.
• Please do not retrofit the light within the warranty period.
• To ensure the light works properly, please use the voltage indicated on the packing.

Remote Controller Instructions

• Manual Mode
  • ‘ON’ button: Turns the flood light constantly ON.
  • ‘OFF’ button: Turns the flood light constantly OFF.
  • ‘D2D’ button: Enters the Dusk to Dawn mode. The light will turn on at night and automatically turn off in the morning.
  • ‘TIMER’ button: Sets the timer for 2/4/6/8 hours in D2D mode. The light will turn on for the specified time and then turn off. This cycle repeats daily.
  • ‘BRIGHTNESS’ button: Adjusts the brightness level to 10%/50%/80%/100%.
• D2D Mode
  • ‘ON’ button: Exits the D2D mode.
  • ‘OFF’ button: Exits the D2D mode.
  • ‘D2D’ button: Enters the D2D mode.
  • ‘TIMER’ button: Exits the timer.
  • ‘BRIGHTNESS’ button: Exits the brightness adjustment mode.

Note:

1. The remote controller has a memory function, which means it will start at your last chosen mode and settings.
2. The flood light is controlled by the IR remote controller. To ensure optimal performance, please point the remote controller towards the light and make sure there are no obstacles between them for better signal response.
3. After a period of usage, the remote controller might run out of battery and become insensitive or the control distance may be shortened. If the remote controller is not working, please try to replace its battery following the instructions shown below. If the remote controller still fails to work after replacing the new battery, please contact the seller for help.

FAQ

How do I replace the battery in the remote controller?
To replace the battery, follow these steps:

1. Remove the plastic sheet from the bottom of the remote controller to activate it.
2. Open the battery compartment on the back of the remote controller.
3. Take out the old battery and dispose of it properly.
4. Insert a new battery into the battery compartment, making sure to align the positive (+) and negative (-) terminals correctly.
5. Close the battery compartment securely.

Contact Us

If you have any issues or questions, please reach us via the following channels:

• Website: www.ustellar.com

• Email: support@ustellar.com

• Manufacturer: Shenzhen Ustellar Technology Ltd.
  Address: 308A, 3/F, Building A, Youth Entrepreneur Hub, Jianshe East Road, Qinghua Community, Longhua Street, Longhua District, Shenzhen, CHINA 518000

• Manual Version: UT88125W-DW-US / V1.0

• Step 1: Scan the QR code

• Step 2 : Click E-manual PDF file

• Step 3: Read file online or download

Thank you for ordering from Ustellar. Set-up is easy and takes only a few minutes by following the instructions.

Warning

1. Please check if the light and the parts are intact before installation.
2. Make sure to cut oË› power before installation.
3. ° Please do not place this light in corrosive conditions.
4. If there is any damage to the cord, please cut oË› the power and stop using it immediately.
5. Please do not retrofit the light within the warranty period.
6. To ensure the light works properly, please use the voltage indicated on the packing.

Parameters

• Model: UT88868
• Wattage: 100W
• Color Temperature: 5000K
• Max Luminous Flux: 10000lm
• Input Voltage: AC120V
• Frequency: 50/60Hz
• Waterproof Rating: IPX1
• Beam Angle: 1 degree
• Controlled By: D2D Sensor & IR Receiver
• Battery for Controller: Yes
• Life Expectancy: Not specified
• Working Temperature: Not specified

Components

Note: Cord – type Y attachment.
For type Y attachment: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

Dimension

Installation

• Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.

• Step B: Aim the bracket at the holes and fix it with two bolts.

• Step C: Adjust the lighting direction up or down as per your need and plug in to power the light on.

• Step D: Remove the plastic sheet from the bo˝om of the remote controller so as to activate the controller.

Note: Limitation of Indoor and Outdoor Use

1. This light is waterproof and damp proof. It is protected against the rain, but it cannot be immersed in water.
2. The mounting position of this light should be able to bear at least 10 times as heavy as the light.
3. This light should be used in condition that is good for heat dissipation. Its working temperature should be less than 40°C Too high the working temperature will cause serious lumen depression and affect lifespan of the light.
   The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire shall be replaced.

Remote Controller

• Manual Mode:
  Control the flood light constantly ON or OFF.

• D2D Mode:

  • Dusk to Dawn mode, the light will turn on at night, and automatically turn o˛ in the morning.
  • Press ‘D2D’ bu˝on will enter the D2D mode.
  • Press ‘ON’ or ‘OFF’ bu˝on will exit the D2D mode.

• TIMER°

  • In D2D mode, turn on for 2/4/6/8 hours, then turn o˛, cycle daily.
  • Press ‘2H’, ‘4H’, ‘6H’ or ‘8H’ bu˝on will enter the timer.
  • Press ‘ON’, ‘OFF’ or ‘D2D’ bu˝on will exit the timer.

• BRIGHTNESS°
  Set the brightness level to 10%/50%/80%/100%.

Note:

1. The remote controller has memory function, which means that it can start at your last choice on mode and se˝ings.
2. The flood light is controlled by the IR remote controller. To make it work perfectly, please point the remote controller to the light and make sure there is no obstacle between the light and the remote controller for be˝er signal response.
3. After a period of usage, the remote controller might run out of ba˝ery and become insensitive or the control distance may be shortened. If the remote controller is not working, please try to replace its ba˝ery as per instructions shown below. If the remote controller still fails to work after replacing new ba˝ery, please contact the seller for help.

The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire shall be replaced.
SUITABLE FOR WET LOCATIONS；
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40°C；

Contact Us

Have some issue? No worries! Please reach us via these channels. Our customer services team is more than happy to help.

• www.ustellar.com
• support@ustellar.com

ABOUT COMPANY

• Manufacturer: Shenzhen Ustellar Technology Ltd. (shen zhen shi you shi tuo ke ji you xian gong si )
• Address: 308A, 3/F, Building A, Youth Entrepreneur Hub, Jianshe East Road, Qinghua Community, Longhua Street, Longhua District, Shenzhen, CHINA 518000

References

• Ustellar | Smart Decor Lighting Innovator

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>