reolink RLC-81PA 4K 180 Degree Pan Rotation PoE Camera Instruction Manual

reolink RLC-81PA 4K 180 Degree Pan Rotation PoE Camera

Product Information

What’s in the Box

Specifications

• Size: 70 x 134 x 140mm
• Weight: 603g
• Operating Temperature:  -10°C~+55°C (14°F~131°F)
• Operating Humidity: 10%~90%
• Waterproof Rating: IP66

For more specifications, visit the Reolink official website.

Connection Diagram

Before using the camera, please connect your camera as instructed below to finish initial setup.

1. Connect the camera to a Reolink NVR (not included) with an Ethernet cable.
2. Connect the NVR to your router, and then power on the NVR.

NOTE: The camera should be powered with a 12V DC adapter or a PoE powering device such as PoE injector, PoE switch or Reolink NVR (not included in the package). * You may also connect the camera to a PoE switch or PoE injector.

Set up the Camera

Set up the Camera Using a Smartphone

1. Scan to download the Reolink App from the App Store or Google Play store.
2. If you are connecting the camera to a Reolink PoE NVR, please set up the camera via the NVR interface.

Mount the Camera

Installation Tips

• Do not face the camera towards any light sources.
• Do not point the camera towards a glass window. Or, it may result in poor image quality because of the window glare by infrared LEDs, ambient lights or status lights.
• Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may result in poor image quality. To ensure best image quality, the lighting condition for both the camera and the capture object shall be the same.
• To ensure better image quality, it’s recommended to clean the lens with a soft cloth from time to time.
• Make sure the power ports are not directly exposed to water or moisture and not blocked by dirt or other elements.
• With IP waterproof ratings, the camera can work properly under conditions like rain and snow. However, it doesn’t mean the camera can work underwater.
• Do not install the camera at places where rain and snow can hit the lens directly.
• The camera may work in extreme cold conditions as low as -25°C. Because when it is powered on, the camera will produce heat. You may power on the camera indoors for a few minutes before installing it outdoors.

Install the Camera

1. Find a desired location and drill holes in accordance with the mounting hole template. Install the mount base with the mounting screws included in the package.
   NOTE : Use drywall anchors included in the package if needed.

2. Loosen the adjustment knob on the mount base and rotate the camera until the desired view is set. Tighten the adjustment knob to secure the camera in position.
   NOTE
   After the installation, you can remotely control your camera from Reolink App to spin left and right for the best field of view.

Note : After the installation, you can remotely control your camera from the Reolink App to spin left and right for the best field of view.

Troubleshooting

Camera is Not Powering On
If your camera is not powering on, please try the following solutions:

• Make sure your camera is powered properly. The PoE camera should be powered by a PoE switch/injector, the Reolink NVR or a 12V power adapter.
• If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see if the camera will power on.
• Try again with another Ethernet cable.

If these won’t work, contact Reolink Support

Picture is not Clear
If the picture from the camera is not clear, please try the following solutions:

• Check the camera lens for dirt, dust or spiderwebs, please clean the lens with a soft, clean cloth.
• Point the camera to a well-lit area, the lighting condition will affect the picture quality a lot.
• Upgrade the firmware of your camera to the latest version.
• Restore the camera to factory settings and check out again.

Spotlight is not On
If the spotlight on your camera is not on, please try the following solutions:

• Ensure the spotlight is enabled under Device Settings page via Reolink App/Client.
• Upgrade the firmware of your camera to the latest version.
• Restore the camera to factory settings and check out the spotlight light settings again.

If these won’t work, contact Reolink Support
Spotlight is not On
If the spotlight on your camera is not on, please try the following
solutions:

FAQ

Q: Where can I find more specifications?
A: For more specifications, please visit the Reolink official website.
Q: Is this product compliant with regulations?
A: Yes, this product is compliant with EMC Directive 2014/30/EU, LVD 2014/35/EU, Electromagnetic Compatibility Regulations 2016, and Electrical Equipment Safety Regulations 2016.
Q: Does this device comply with FCC rules?
A: Yes, this device complies with Part 15 of the FCC Rules.
Q: What should I do if the suggested solutions don’t work?
A: If the suggested solutions don’t work, please contact Reolink Support for further assistance.

Camera Introduction

1. Spotlight
2. Lens
3. IR LEDs
4. Daylight Sensor
5. Micro SD Card Slot
6. Speaker
7. Adjustment Knob
8. Waterproof Lid
9. Network Cable
10. Reset Button

• Press for about 10 seconds to restore the device to factory settings. 11. Power Port(Optional)

Notification of Compliance

CE Declaration of Conformity
Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of EMC Directive 2014/30/EU and LVD 2014/35/EU.
UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Electromagnetic Compatibility Regulations 2016 and Electrical Equipment Safety Regulations 2016.
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.
ISED Compliance Statements
This Class B digital apparatus complies with Canadian ICES-003.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other household wastes.throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Limited Warranty

This product comes with a 2-year limited warranty that is valid only if purchased from Reolink Official Store or a Reolink authorized reseller.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and Privacy Policy at reolink. Keep out of reach of children.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>