Rebluum V1 Solar Battery-Wireless Security Camera User Guide

Solar Battery
-Wireless Security Camera Quick Start Guide

Toll Free: +1844 4971656 (US ONLY)
Available after 5: 30 PM at Pacific Time
support@szrebluum.com
Youtube: Rebluum Security

What’s included

Scan and Enter the Activation Code to Get Video Tutorial

http://service.viziuuy.com/prize

Note: The power cable of the solar panel is 9.2feet.

Product overview

CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and device could be damaged.
D Card Port: Support micro SD card for local storage (Max 128GB).
Reset button: Used to restore the camera to factory settings (Press and hold on 5-85).
Card capacity requirements: 8-128GB.
Read and write
speed requirements: Class10 Level.
File format: FAT32. (Please format the SD card for the first use)Please refer to the FAQ 4.

Cloudedge App download Setup

1. Search ” CloudEdge” on apple store or google play to download the app.
2. Scan the following QR code.https://itunes.apple.com/app/id1294635090?mt=8 https://play.google.com/store/apps/details?id=com.cloudedge.smarteye 
   Scan and Enter the Activation Code to Get Video Tutorial. http://service.viziuuy.com/prize

TIPS: APP Permission Settings
When using the application for the first time, please turn on the following 2 permissions.

1. Allow”Cloudedge”to access mobile cellular dataand WLAN, otherwise you will not be able to add devices.
2. Allow “Cloudedge” to receive messages, otherwise the phone will not receive alert push notifications when motion detection oraudible alerts are triggered.

The followingis ascreenshot of iOS cellphone operation, Android cell phone permissions open method is basically the same as this method.

Mounting the camera

Select Height and location
Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor Avoid placing the camera under direct sunlight. Installation

1. Drilling according to position sticker, dril bit: 15/64(6 mm).
2. Insert the plastic anchors.
3. Tighten the screw.

What is required: Installation instruction of solar panel

1. Keepthe installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
2. The installation between the solar panel and the camera is shown in the following figure(open up the silicone cover at the bottom of the camera, remove the small center part of the cover, insert the power cord through the opening and plug it into the Type C port).

Tips for the installation of solar panel

1. : Please keep the solar panel at an angle that can be directly exposed to the sun.
2. : Please avoid shading on the solar panel.
3. : Check the power indicator,make sure it is red (except the camera at full charge) .

Test the Wifi signal at installation position
Make sure the wifi signal value is above 75 before installation.

Register an account

The Cloudedge APP is totally free for remote access.
As for storage.you can use a mirco SD card or pay for the cloud service..

1. Enter the app and tap the “sign up now”at the bottom side
2. Sign up with your email address, and click “Next”.
3. Setup an “Nickname” and “Password” for your APP, click “Done” to complete.

Set up WiFi for the camera

1. Set up the camera near by the router.
   Note: The camera can only connect to a 2.4 GHz WiFi signal. It does not support using a 5 GHz signal. You can confirm your home wifi is 2.4Ghz or not via the sticker on your home router.
   PS:Please contact us if your router is dual-band .

2. Login to “CloudEdge”, then tap the “+” icon in the center. Tap “Battery Camera to add device.

Reset the camera by holding the reset button for about 5 seconds the device is reset successfully i you hear a”BUGU” tone,then tap Next .

1. Selecting the 2.4Ghz wifi, input the password and click next .

2. Please double check the wifi name and password and tap OK .

3. You will get a QR code on the app after you tap next

4. Use the camera to scan the QR code on your mobile phone.

5. Tap next untill you hear a “BUGU” tone.

![Rebluum V1 Solar Battery Wireless Security Camera - QR Code 6](https://manuals.plus/wp-content/uploads/2023/08/Rebluum-V1-Solar-Battery-Wireless-Security-Camera-QR-Code-6.png)

1. Wait for the network configuration,the indicator turns to blue means camera added successfully.
2. Tap next, get ive view.

Alarm Management
Tap to the setting button select alarm management

1. 10 means top sensitivity, 1 means the lowest.
2. Tap Custom mode,tum on the humanoid detection to reduce the false alarm.
3. If you want to detect all the moving objects, please turn off the humanoid detection.
4. The default recording time is 10S,, you can select 208, 30S depend on your needs.

Audio warning and strobe light
Audio warning and strobe lightis only valid at night.
Tap setting icon,choose alarm managementtap audio warning and strobe lightturn on.

Device Share
If your family members want to view,you can share the camera by the following steps

1. Ask your family members to download the cloudedge app and sign up a new account with email
2. Operate on your own account,click the setting button and select device share-add-enter account and input your family members email account.
3. Your family member will get a invitation request,click agree to join.

FAQ

Q1: The device prompts offine?

A: o Check whether the Camera is in the power-on state. o Check whether the Wi-Fi network is in good condition and restart the router. Put the camera near by the routertry again. « Delete the camera from your Cloudedge APP account and add itagain after resetting the device. Check whether the device firmware and application programare the latest version. : o Check whether the Camera is in the power-on state. o Check whether the Wi-Fi network is in good condition and restart the router. Put the camera near by the routertry again. « Delete the camera from your Cloudedge APP account and add itagain after resetting the device. Check whether the device firmware and application programare the latest version.

Q2: Why the device is still in the list after reseting?

A: The device reseting is only for the parameter configurations of the camera, not for App configuration. If you want to remove the camera, Please just delete it from the APP end.

Q3 :How to change the camera network to another router?

A :First remove and reset the device on the App and then configure the device again by the App.

Q4 :Why the SD card can not be indentified?

A: 1. Please plug in SD card after power cut. 2. Confirm whether the SD card is normal and the format is FAT32. Please note: TF card may not be identified when the Internet environment is not good. 3. Please format the SD card for the first use,tap the setting icon, choose recording management,tap the format button.

Q5 : Why I can't get the notifications with my cell phone App?

Satety Statement

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer- ence received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica- tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
IC Caution:
Radio Standards Specification RSS-Gen, issue 5
– English:This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’ s licence- exempt RSS(s). Operation is subject to the following two conditions:This device may not cause interference.This device must accept any interference, including interference that may cause undesired operation of the device. RF exposure statement:The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
UK Caution:
The device is in compliance with the essential requirements and other relevant provisions of the UK Radio Equipment Regulations S| 2017:1206 (as amended).

1. The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
2. The device complies with RF specifications when the device used at 20cm form your body.

Declaration of Conformity:
Hereby, Shenzhen Anked Electronics Co., Ltd declares that the product V1 is in compliance with the following Regulations: Radio
Equipment Regulations 2017, Electrical
Equipment (Safety) Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electrical Equipment 2012. The Full test of the UK declaration of conformity is available at the following internet address:www.viziuuy.com
Manufacturer Name:Shenzhen Anked Electronics Co., Ltd
Manufacturer Address:Room 302, Infinova technology company factory building,No.
Guanbao Road, Luhu Community, Guanhu Street, Longhua District, Shenzhen
Transmitter power: 18.64dBm
TX/RX Frequency Range: 2412-2472MHz Cn Warranty Tips
Pleasefillin the followinginformation or scan QR code to activate the free 12-month warranty from the order dateon.
After finishfilling or scanning, please take a picture and senditto the email(support@szrebluum.com).
Then your free warranty will take effect!
During the warranty period, if any parts of product are damaged, please contact usimmediately and we will provide satisfactory resolution.
Order Date:…………………..
Order Number/ID:………………
Buyer E-mail:………………….
Buyer Tel:……………….
Contact us

support@szrebluum.com
+1844 497 1656
  Youtube: Rebiuum Security http://service.viziuuy.com/prize
support@szrebluum.com
+1 844 497 1656

Documents / Resources

| Rebluum V1 Solar Battery-Wireless Security Camera [pdf] User Guide
2BBVZ-V1, 2BBVZV1 v1, V1, Solar Battery-Wireless Security Camera, V1 Solar Battery-Wireless Security Camera, Battery-Wireless Security Camera, Wireless Security Camera, Security Camera, Camera
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>