Rebluum RB-3PT1-2PACK Solar Security Cameras Wireless Outdoor User Guide

Rebluum RB-3PT1-2PACK Solar Security Cameras Wireless Outdoor

What’s Included

Product Overview

CAUTION: Please insert the Micro SD Card according to the direction shown in the diagram. Micro SD Card might JAM if inserted incorrectly and the device could be damaged.

• SD Card Port: Support micro SD card for local storage (Max 128GB).
• Reset button: Used to restore the camera to factory settings (Press and hold on 5-Bs).
• Card capacity requirements: 8-128GB.
• Read and write speed requirements: class1 O level.
• File format: FAT32.

Cloud Edge App Installation and Setup

Search” Cloud Edge” on the apple store or google play to download the app.

• from Google Play
• from Apple Store
• or Sean the following QR code

Download App( 10S & android)

Mounting the camera

Select Height and location

• Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes the detection range of the motion sensor of the camera. Avoid placing the camera under direct sunlight.

Installation

1. Drilling according to position sticker, drill bit: 15/64″(6 mm).
2. Insert the plugs.
3. Tighten the screw.

What is required

Installation instructions for solar panels

1. keep the installation angle of solar panels about 30-45° with the horizontal plane, as shown in the picture below.
2. The installation between the solar panel and the camera is shown in the following figure(open up the silicone cover at the bottom of the camera, remove the small central part of the cover, insert the power cord through the opening, and plug it into the Type C port and then close the cover taking up any slack in the power cord from the solar panel).

Tips for the installation of solar panel

1. When installing in the northern hemisphere, face the panel to the south, and when installing in the southern hemisphere, face the panel to the north.
2. Take care to install the solar panel so that the sun is not blocked by any items such as eaves, tree branches, etc.

Test the Wifi signal at the installation position
Use a cell phone to test the Wifi signal quality at the installation position before installing the camera, make sure the Wifi router can provide a good Wifi signal.

Register an account

The Cloud Edge app is necessary to operate the camera. Signing up for storage in the cloud is totally optional and is really not necessary when using an onboard Micro SD card.

1. Open the APP to sign up for an account. Go to the login interface, and click “Sign Up”.
2. Sign up with your email address, and click “Next”.
3. Set up a “Nickname” and “Password” for your APP, and click “Done” to complete.

Set up WiFi for the camera

1. Bring both your mobile phone and your camera close to your router (max distance of 5 meters/16 feet).
   Note: The camera can only connect to a 2.4 GHz WiFi signal. It does not support using a 5 GHz signal. Therefore, please ensure you connect to a 2.4 GHz signal on your network as shown in the below illustration.

2. Log in to “Cloud Edge”, then tap the”+” icon in the center. Tap “Battery Camera” to add a device.

3. Reset the device and wait for a flashing RED indicator light, then tap •Next”.

4. Selecting the Wi-Fi the device needs to connect with (your home Wi-Fi), input the password, and click “Next”.

5. Use the camera to scan the QR code on your mobile phone as noted below. When the scan is complete you will hear a prompt tone then push Next.

6. After the network configuration is successful, set the name and password for the device to add successfully, then you can view the camera screen in real-time.

Humanoid Detection

Turn on humanoid detection, the alert will be triggered only when human motion is detected. Click the Settings button. and select nAlarmManagement• then enable nMotion Detection” click “Alarm Working Mode”, select “Custom Mode” and click the Settings button to set the humanoid alarm. Recording Time: The duration of each alarm video; Alarm Interval: Interval of each alarm push.

Tips: If you want to detect other moving objects such as vehicles, please turn off the humanoid detection switch. don’t turn on “Day Detection” and “Night Detection”.

Audio warning and strobe light

Audio warning and strobe light are only valid at night.

Device Share

The camera can only be added by one APP account. If other family members want to view the camera, you can share the camera with your family through the sharing function of the APP. Click the Settings button and select “Device Share”➔”Add11➔11 Enter account• and input the other party’s APP account, then your family will receive a shared message on the APP, click Agree to view the camera you shared.

FAQ

• Q: Is the device prompted offline?
• A:   Check whether the equipment is in the power-on state.
• Check whether the Wi-Fi network is in good condition and restart the router.
• If the device is located far away from the router, which results in the inability to obtain a good Wi-Fi signal, it is recommended to move the router to a closer place or add a Wi-Fi amplifier to improve the Wi-Fi performance of the home.
• Delete the camera from your Cloudedge APP account and add it again after resetting the device.
• Check whether the device firmware and application program are the latest version.
• Q: Why is it still on the list of devices after resetting?
• A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App.
• Q: Why is it still on the list of devices after resetting?
• A: The reset device only resets the network configuration of the camera, but cannot change the configuration on the App, remove the camera, and must be deleted by the App. Q: How to cut the camera network to another router?
• A: First remove and reset the device on the App and then configure the device again by the App.
• Q: Why doesn’t the device identify the SD card?
• A: It is recommended to plug in an SD card after the power cut. Confirm whether the SD card is normally available and whether the format is FAT32. And the TF card can’t be identified when the internet environment is not good.
• Q: Why I can’t get the notifications with my cell phone App?
• A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been opened.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC Radio Frequency Exposure Statement

• The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The min separation distance is 20cm.
• Notice: Shielded cables
• All connections to other computing devices must be made using shielded cables to
  maintain compliance with FCC regulations.

Warranty Tips

• Please fill in the following information or scan the QR code to activate the free 12-month warranty from the order date on.
• After finish filling or scanning, please take a picture and send it to the email(support@szrebluum.com).
• Then your free warranty will take effect! During the warranty period, if any parts of a product are damaged, please contact us immediately and we will provide satisfactory resolution.
• Order Date: —————-
• Order Number/ID: ————-
• Buyer E-mail: —————
• Buyer Te 1:—————–

Contact us

support@szrebluum.com 1844 4971656 0 Youtube: Rebluum Security

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>