eSSL AIFACE-PLUTO 4-Inch Visible Light System User Guide

June 4, 2024
eSSL

eSSL AIFACE-PLUTO 4-Inch Visible Light System

eSSL AIFACE-PLUTO 4-Inch Visible Light System PRODUCT-
IMG

Overview

eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(1\)

Installation Environment

Please refer to the following recommendations for installationeSSL AIFACE-
PLUTO 4-Inch Visible Light System FIG \(2\) eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(3\)

Recommended Palm Gestures

eSSL AIFACE-PLUTO 4-Inch Visible Light System
FIG \(4\)

Note:

  1. Place your palm within 30-50 cm of the device.
  2. Place your palm in the palm collection area, such that the palm is placed parallel to the device.
  3. Make sure to keep space between your fingers.

Recommended Standing Position

Device Installation

eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(7\)

  1. Attach the mounting template sticker to the wall, and drill holes according to the mounting paper. Fix the back plate on the wall using wall mounting screws.
  2. Attach the device to the back plate.
  3. Fasten the device to the back plate with a security screw

Standalone Installation

eSSL AIFACE-PLUTO 4-Inch Visible Light System
FIG \(8\)

Power Connection

eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(9\)

Ethernet Connection

eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(10\)

Click [COMM.] > [Ethernet] > [IP Address] , input the IP address and click [OK].
Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment when connecting to BioAccess IVS software

Lock Relay Connection

The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (normally opened when powered) is connected with ‘NO1’ and ‘COM’ terminals, and the NC Lock (normally closed when powered) is connected with ‘NC1’ and ‘COM’ terminals. The power can be shared with the lock or can be used separately for the lock, as shown in the example with NC Lock below:

  1. Device not sharing power with the lockeSSL AIFACE-PLUTO 4-Inch Visible Light System FIG \(11\)
  2. Device sharing power with the lockeSSL AIFACE-PLUTO 4-Inch Visible Light System FIG \(12\)

Door Sensor, Exit Button & Alarm ConnectioneSSL AIFACE-PLUTO 4-Inch
Visible Light System FIG \(13\)

Wiegand Reader Connection

Wiegand card reader connects to the top 4 pins of the wiegand terminal and the last two pins are used by the Access Controller, as shown in the following figure. It sends the credentials to the device via wiegand communicationeSSL
AIFACE-PLUTO 4-Inch Visible Light System FIG \(14\)

RS485 Connection

The RS485 lets user connect to multiple readers to the device. RS485 can be connected to the terminal, as shown in the figure beloweSSL AIFACE-PLUTO
4-Inch Visible Light System FIG \(15\)

User Registration

When there s no super administrator set in the device, click on to enter the menu. Add a new user and set User Role to Super Admin, then the system will request for the administrator’s verification before entering the menu. It is recommended to register a super administrator initially for security purposes

Method 1: Register on the device

Click on > [User Mgt.] > [New User] to register a new user. The options include entering the user ID and Name, setting User Role, registering Palm, Face, Card Number, Password and adding User PhotoeSSL AIFACE-PLUTO 4-Inch
Visible Light System FIG \(16\) eSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(17\)

Ethernet and Cloud Server Settings

Click on > [COMM.] > [Ethernet] to set the network parameters. If the TCP/IP communication of the device is successful, the icon will be displayed in the upper right corner of the standby interface
Click on > [COMM.] > [Cloud Server Setting] to set the server address and server port, that is, the IP address and port number of the server after the software is installed. If the device communicates with the server successfully, the icon will be displayed in the upper right corner of the standby interfaceeSSL AIFACE-PLUTO 4-Inch Visible Light System FIG
\(18\)

Note:

While pairing the device with ZKBioAccess IVS software. Make sure that the option

Enable Domain Name is disabled and the correct server address and port are entered.
Server Address : Set as the IP address of the ZKBioAccess IVS server.
Server Port : Set as the service port of ZKBioAccess IVS(the default is 8088

Access Control Setting

Click on > [Access Control] to enter the access control management interface and set relevant parameters of access controleSSL AIFACE-PLUTO 4-Inch
Visible Light System FIG \(19\)

Attendance Record

Click on  > [Attendance Search] > [Event Logs] to enter the logs query interface, input the user ID and select the time range, the corresponding event logs will be displayed.eSSL AIFACE-PLUTO 4-Inch Visible Light System
FIG \(20\)

24, Shambavi Building, 23rd Main, Marenahalli,JP Nagar 2nd Phase, Bengaluru –

560078
Phone : 91-8026090500
Email : sales@esslsecurity.com
www.esslsecurity.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals