eSSL TL200 Fingerprint Lock With Voice Guide Feature Instruction Manual
- June 5, 2024
- eSSL
Table of Contents
- eSSL TL200 Fingerprint Lock With Voice Guide Feature
- Before Installation
- Packing List
- Door Preparation
- Tips
- Cautions
- Installation
- Install outdoor unit(B) with gasket(C),and spindle(D)
- 24, Shambavi Building, 23rd Main, Marenahalli, JP Nagar 2nd Phase, Bengaluru
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eSSL TL200 Fingerprint Lock With Voice Guide Feature
Before Installation
Packing List
Door Preparation
- Check door thickness, prepare the proper screws and spindles.
Door Thickness| D Spindle| L Spindle| J Screw| K Screw
---|---|---|---|---
35-50 mm|
85 mm
|
60 mm
| 30 mm| 45 mm
50-60 mm|
45 mm
| 55 mm
55-65 mm| 60 mm
65-75 mm| 105 mm|
85 mm
| 55 mm| 70 mm
75-90 mm| 125mm| 70 mm| 85 mm
2. Check door open direction.
Note: 1. Please install the mortise and strike plate according to the
above pictures.
- Check door type.
Mortise without hooks is applied to wooden door, and mortise with hooks is applied to security door.
Tips
-
How to change the direction of latch bolt?
Step1: Push the switch to the end
Step2: Push the latch bolt into the mortise
Step3: Rotate the latch bolt at 180° inside mortise, then loose it. -
How to change the handle direction?
-
How to use mechanical key?
-
How to use emergency power?
-
How to change the location of stud bolts?
-
Step1: Twist down the ten M3 screws and M5 stud bolt to take down the mounting plate.
Note: For the door with the existed holes, you can adjust stud bolts location to make the lock suitable. -
Step2: Twist down the other stud bolt.
Note: There are four square holes to be used.
Note: There are two round holes to be used.
Cautions
-
New lock is configured to grant ANY fingerprint access to unlock.
-
Please register one administrator at least for the new installed lock, If there is no any administrator, registration for normal users and temporary users are not allowed.
-
The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the package and keep them in a safe place.
-
To power on the lock, eight alkaline AA batteries (not included) are required.
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED. -
Do not remove batteries when the lock is in working state.
-
Please replace the battery soon when the lock prompts the voice of low battery.
-
The operation of setting lock has a stand-by time limit of 7 seconds. Without any activity, lock will shut off automatically.
-
Keep your fingers clean when using this lock.
Installation
Drill holes on the door
Note1: Align the template along the vertical center line of the
mortise(E)at the desired handle height, and tape it to door.
Note2: Mark the holes first, then start drilling.
Install the mortise(E)
Install outdoor unit(B) with gasket(C),and spindle(D)
Note:
-
The small triangle must be placed toward the letter of R or L.
-
When the small triangle is towards to R, it is right open.
-
When the small triangle is towards to L, it is left open.
-
Install mounting plate (I) with gasket(C), and spindle(L)
-
Install indoor unit (M)
-
Install battery (O)
Note: Push cable into the hole. -
Step1: Place the battery cover in the position as above picture showed, then press down it gently.
-
Step2: Sliding down the battery cover.
-
Mark and drill holes for strike
-
Test the lock by mechanical key(A) or fingerprint
Mechanical Key Instruction: -
Key A is coated with brass color, which is used only for lock installer and upfitter.
-
Key B is packed in the sealed plastic wrap for safety, which is used for house owner.
-
Once Key B is used, Key A will be disabled to open the lock.
24, Shambavi Building, 23rd Main, Marenahalli, JP Nagar 2nd Phase, Bengaluru
– 560078 Phone : 91-8026090500 | Email :
sales@esslsecurity.com
www.esslsecurity.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>