eSSL Security D270-1-IP54 Walk Through Metal Detector Single Zone Door Side Controller Instruction Manual
- June 2, 2024
- eSSL Security
Table of Contents
- eSSL Security D270-1-IP54 Walk Through Metal Detector Single Zone Door
- Control Panel Settings
- Input password
- Revising password
- Function Setting
- Product Introduction
- Technology advantages
- Specification
- Application occasions
- Common Fault Handling
- Kind Attention
- Multiple devices work side by side
- Before working, device setting
- Installation 1nstruct1ons
- Detection Zones Diagram of Walkthrough Metal Detector
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eSSL Security D270-1-IP54 Walk Through Metal Detector Single Zone Door
Side Controller
INSTRUCTION MANUAL
Control Panel Settings
Input password
Boot and press key to change the program bottom, display P 00000, enter the password, the initial password is P 0000, press 6 corresponding selection number (from 0 to 9 cycle), press 5 key to change selection (can cyclic shift, choose corresponding bit twinkle), if password fault (CERR), can’t enter the system, press 6 key to re-enter the password ,until the correct password, then press 7 key(setting botton) access the interface of setting specification.
Revising password
To change the password, press the 7 key (setting key) to switch to the screen
display P 00000, press the 7 key (setting key) for 5s, and then the
corresponding selection position will start flashing.
Press the 6 key to change the value of the corresponding selection bit (0-9
cycles), and press the 5 key to change the selection bit (cyclic shift, and
the corresponding selection bit will flash). At this time, you can enter a new
password, and press the 7 key to save and enter.
Please read the manual carefully and thoroughly before operating the
equipment.
Users keep this manual for reference at any time
Function Setting
- Before revising device specification.please read this section carefully.
- Note: when enter into next interface, spec value of last interface equal to the last operation value
Product Introduction
Muti-zone intelligent walkthrough metal detector with high performane,in the meantime ,it have higher sensitivity, light weight, best resistance of interference and perfect stability. This model adopts high strength material, more lighter and convenient transportation and installation. With Fully modular product, assembly on flow line production,so can keep the stability of production. It is easy to operate with Intuitive interface. So can operate without any trainning.
Muti-zone intelligent walkthrough metal detector is widely used in athletic
meeting,conference,school etc.
This item is gotten shape patent,and achieve right of software registration.
Its detection theory is to use electromagnetic field to detect metal
object,and even detect Metal quantity by acousto-optic alarm mode. It consists
of the main unit, HF signal generator, infrared sensor. It is most advanced
metal detector gate with elegant shape, superior detection ability, muti-zone
detection, unique operation network system, portable features.
Technology advantages
- Adaptive system: when system enters into adaptive mode, it can adapt the testing standard
- Start-stop technology: The infrared device is equipped with automatic start-stop technology, which prolongs the service life by 100 times
- The sensitivity of Each detection zone can be adjusted randomly ( with adaptive technology )
- Can Change the detection zones (customer oneself can convert detection zones easily)
- For Sound, Light alarm, alarm tone, alarm time length, can be change randomly.
- Query function: the system with real-time information query function.
- Detection ability: at least detect 100 persons within one minute.
Specification
- Detect object: contraband including mobile phone and metal
- Working humidity: 99%,non-condensing
- Working temperature: -40″C-60″C
- Power supply: can equip with backup battery. Can choose different supply time from 8/16/24/48
- hours(optional)
- Input: AC 110 V-240 V/50HZ-60HZ
- Output: DC 12 V/4.2A 12W
Application occasions
Walkthrough metal detector is used to detect metal object in the body.
Typical application occasions as following:
- Airport,port: travelling check point
- Court,prison: visiting check point
- Conference,public building,stadium: entering control
- Power plant: staff,visiting check point
- Factory: anti-theft
- Hotel,restaurant,entertainment,KTV:visiting check point By research and practice of long terms, we published this style device. And it also is use advanced technology and 100% security. According to the manual operating,will not exist any damage for the person passing through device.
Common Fault Handling
Kind Attention
Installation environment
Shaking Ground
Ground should be flat, with a solid support, to prevent vibration. Especially
when there is presence of vibration of the metal structure under the surface,
people walk through the detector may cause unnecessary alarms.
Fixed the metal objects
The distance between fixed or a large metal object should be at least 10cm
{4in) away from the WTMD to detect large metals. It has little effect on the
sensitivity. but it may make WTMD more susceptible to vibration.
The distance of this section is recommend distance.
the actual distance should be decided upon the installation site conditions.
The moving metal objects
The moving metal objects outside the WTMD should keep a distance of 0.5-2m
(20-79inl away from the door, thus to avoid false alarms.
According to the size of metal objects, the distance between metal objects and
the WTMD may be different.
Radiated electrical interference
The distance between electronic interference source and the receiving coil is
the largest. The recommended minimum distance should be 0.5-4m (20-157in).
However, the actual distance should be depended on the real conditions. For
example, you can move the WTMD and the interference source to find the best
position.
Interference may be provided by electronic control panel. radios and computers, image display, high-power motors and transformers. AC cord. thyristor control circuits. flash welding equipment fluorescent tubes and other equipment.
Conductivity electronic interference
Connect the power cord to which is not connected to other large load (such as
high-power motors, etc). They may result in a large power line or voltage
shocks.
Multiple devices work side by side
The recommended minimum distance between the interference source.
0.5m-4m(20in-157in)
0.5m-2m(20in-79in)
0.1 m(4in) NOTICE
Please first read this section before installing device.
A: The distance between the fixed metal objects
B: There must be no movable metal objects
C: There must be no electrical interference sources
Work side by side means mutiple devices work close to each other. When it works side by side,walk through metal detector will interfere each other in a certain extent. Interference level is decided the distance between the devices, working frequency, sensitivity.
There is many different working frequencys choosen for walk through metal detector,so can reduce the interference between device in order to work side by side.Please note,when it works side by side ,all device should set different working frequency.
Before working, device setting
Operator passes through walk through metal detector with need to be detected metal. In the meantime adjust sensitivity and security level,so that achieve customer’ s demands
Installation 1nstruct1ons
Crossbeam series Installation instrucHons CD
If need our technology supporting when installing and operating or setting
specification,please call our service hotline. (refer to cover service card )
If have any doubt and advice regarding our product,please send email to our
email adress. When we received your email,will reply you immediately.
Appreciate your supporting and understanding.
Crossbeam series Installation instructions@
If need our technology supporting when installing and operating or setting specification,please call our service hotline. (refer to cover service card )
If have any doubt and advice regarding our product,please send email to our email adress. When we received your email,will reply you immediately. Appreciate your supporting and understanding.
Detection Zones Diagram of Walkthrough Metal Detector
Single Zone
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>