SUPERATV IN-ROOF-CA-X3XRSMAX Maverick X3 MAX Aluminum Roof Instruction Manual
- June 14, 2024
- SUPERATV
Table of Contents
INSTALLATION INSTRUCTIONS
Metal Roof: for Can-Am Maverick X3 MAX
IN-ROOF-CA-X3XRSMAX Maverick X3 MAX Aluminum Roof
– Do not discard packaging until product has been successfully
installed.
Need help with your installation?
| sales@superatv.com| |
www.superatv.com
---|---|---|---
| 1-855-743-3427| | 8:00am – 8:00pm EST
M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
Read instructions and view illustrations before beginning.
Thank You For Choosing
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware
that installing lift kits, long travel, or suspension kits, tires, etc. will
change the ride of machine and may increase maintenance and part wear.
Operating any off-road machine while, or after, consuming alcohol and/or drugs
increases risk of bodily harm or death. No warranty or representation is made
as to this product’s ability to protect user from severe injury or death.
SuperATV® urges operators and occupants to wear a helmet and appropriate
riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should
damages occur, SuperATV® will not be held responsible for loss of time, use,
labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd
party, will not be held responsible for any direct, indirect, incidental,
special, or consequential damages that result from any product purchased from
SuperATV®. The total liability of seller to user for all damages, losses, and
causes of action, if any, shall not exceed the total purchase price paid for
the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or
problems with OEM housings, bearings, seals, or other manufacturers’ products
will not be covered by SuperATV®. SuperATV® parts and products are not
warrantied if item was not installed properly, misused, or modified.
Installing, adding, modifying, or fabricating any factory or aftermarket
product to your ATV/UTV may violate certain local, state, and federal laws. Be
advised that laws vary depending on town, city, county, state, etc. Use of
certain products on public streets, roads, or highways may be in violation
law. The Buyer is solely and exclusively legally and personally responsible
for any violation of the law by the installation or use of the product. You
must abide by all local, state, and federal laws, including but not limited to
vehicle safety, traffic laws, and ordinances. It is your responsibility to
know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of
his/her vehicle according to manufacturer specifications, warnings and
instructions and agrees to hold SuperATV® harmless from any damage resulting
from failure to adhere to such specifications, warnings and/ or instructions.
The Buyer is also responsible to obey all applicable federal, state, and local
laws and ordinances when operating his/her vehicle while using this product,
and the Buyer agrees to hold SuperATV® harmless from any violation thereof.
– Remove stock Brace.
– Install Mounts.
do not tighten any hardware completely unless noted
– Install new Braces.
– Install Sides to Front with hardware shown; keep loose.
– Install Seals along inside of Roof in areas shown.
– Install Small Clamps and Brackets with hardware shown; keep loose.
SuperATV highly recommends an extra set of hands for this step
– Place Roof assembly onto Cage.
– Align Roof to machine.
– Secure Rear to Frame with hardware shown; keep loose.
– Secure Front to Mounts with hardware shown.
tighten Front and Rear hardware completely
– Secure Small Clamps to Cage.
– Secure Roof to Brackets with hardware shown.
– Repeat for passenger side.
– Recheck Roof alignment to machine.
– Tighten all hardware.
IN-ROOF-CA-X3XRSMAX
2753 Michigan Road • Madison, Indiana 47250 •
855-743-3427
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>