reolink Argus 3 Ultra Smart Home Automation Camera Instruction Manual
- June 14, 2024
- reolink
Table of Contents
Operational Instruction
Apply to: Argus 3 Ultra, Argus 3 Pro,
Argus 3 Plus, Argus 3 Plus 4K
What’s in the Box
Camera Introduction
1. USB-C Port
2. Speaker
3. Spotlight
4. Status LED
5. 6 IR Leds
6. Lens
7. Daylight Sensor| 8. Built-in Mic
9. PIR Motion Sensor
10. Reset Button
- Press for more than five seconds to reset the device to factory settings.
11. Power Switch
12. Micro SD Card Slot
13. Battery Status LED
---|---
Different states of the status LED:
Red Light: WiFi connection failed
Blue Light: WiFi connection succeeded
Blinking: Standby status
On: Working status
Set up the Camera
Set up the Camera Using a Smartphone
Step 1 Scan to download the Reolink App from the App Store or Google Play
store.
https://reolink.com/wp-json/reo-v2/app/download
Step 2 Turn on the power switch to power on the camera.
Step 3 Launch the Reolink App, click the “ ” button in the top right corner to
add the camera.
Scan the QR code on the device and follow the onscreen instructions to finish
initial setup.
NOTE: This device supports 2.4 GHz and 5 GHz Wi-Fi networks. It is
recommended to connect the device to 5 GHz Wi-Fi for a better network
experience.
Set up the Camera on PC (Optional)
Step 1 Download and install the Reolink Client: Go to
https://reolink.com > Support > App&Client.
Step 2 Launch the Reolink Client, click the “ ” button, input the UID
code of the camera to add it and follow the onscreen instructions to finish
initial setup.
Charge the Camera
It’s recommended to fully charge the battery before mounting the camera.
Charging Indicator:
Orange LED: Charing Charge the battery with a power adapter. (not included)
Green LED: Fully charged Charge the battery with the Reolink Solar Panel (Not included if you only purchase the camera).
For better weatherproof performance, please always cover the charging port with the rubber plug after charging the battery.
Install the Camera
Notes on Camera Installation Position
- Install the camera 2-3 meters (7-10 ft) above ground. This height maximizes the detection range of the PIR motion sensor.
- For effective detection, please install the camera angularly.
NOTE: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.
Mount the Camera
Drill holes in accordance with the mounting template and screw the base of the
bracket to the wall. Next, attach the other part of the bracket to the base.
NOTE: Use the drywall anchors included in the package if needed.
Screw the camera to the bracket.
Adjust the camera angle to get the best field of view.
Secure the camera by turning the part on the bracket identified in the chart
clockwise.
NOTE: To adjust the camera angle later, please loosen the bracket by
turning the upper part anticlockwise.
Install the Camera with Loop Strap
Thread the loop strap through the slots and fasten the strap. It is the most recommended installation method if you plan to mount the camera to the tree.
Safety Instructions of Battery Usage
The camera is not designed for running 24/7 at full capacity or around-the-
clock live streaming.
It’s designed to record motion events and to live view remotely only when you
need it. Learn useful tips on how to extend the battery life in this post:
https://support.reolink.com/hc/en-us/articles/360006991893
- Do not remove a built-in battery from the camera.
- Charge the battery with a standard and high-quality DC 5V battery charger or Reolink solar panel. It’s not compatible with solar panels from any other brands.
- Charge the battery only if in temperatures between 0°C and 45°C. The battery is intended for use only in temperatures between -10°C and 55°C.
- Keep the charging port dry, clean and free of any debris. Cover it with the rubber plug after the battery is fully charged.
- Do not charge, use or store the battery next to areas that may become hot. Examples include, but are not limited to, on or near a space heater, cooking surface, cooking appliance, iron, radiator, or fireplace.
- Do not use the battery if its case appears damaged, swollen, or compromised. Examples include, but are not limited to, leaking, odors, dents, corrosion, rust, cracks, swelling, melting, and scratches.
- Always follow the local waste and recycling laws to dispose of used batteries.
Troubleshooting
Camera is Not Powering On
If your camera is not powering on, please try the following solutions:
- Make sure the power switch is turned on.
- Charge the battery with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged
If these won’t work, contact Reolink Support.
Failed to Scan QR Code on the Phone
If you cannot scan the QR code on your phone, please try the following
solutions:
- Remove the protective film from the camera lens.
- Wipe the camera lens with a dry paper/ towel/tissue.
- Vary the distance between your camera and the mobile phone so that the camera can focus better.
- Try to scan the QR code under sufficient lighting.
If these won’t work, contact Reolink Support.
Failed to Connect to WiFi During Initial Setup Process
If the camera fails to connect to WiFi, please try the following solutions:
- Ensure that you have entered the correct WiFi password.
- Put the camera closer to your router to ensure a strong WiFi signal.
- Change the encryption method of the WiFi network to WPA2-PSK/WPA-PSK (safer encryption) on your router interface.
- Change your WiFi SSID or password and make sure that SSID is within 31 characters and password is within 64 characters.
If these won’t work, contact Reolink Support.
Specification
Operating Temperature: -10°C to 55°C (14°F to 131°F)
Size: 127 x 90 x 56 mm
Weight: 335g
For more specifications, visit https://reolink.com
Notification of Compliance
CE Declaration of Conformity
Reolink declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU and
Directive 2014/30/EU.
UKCA Declaration of Conformity
Reolink declares that this product is in compliance with Radio Equipment
Regulations 2017 and Electromagnetic Compatibility Regulations 2016.
FCC Compliance Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
ISED Compliance Statements
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
ISED Radiation Exposure statement
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator and your body.
NOTE: Operation of 5150-5250 MHz is restricted to indoor use only in
Canada.
Correct Disposal of This Product
This marking indicates that this product should not be disposed with other
household wastes.throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmentally safe recycling.
Limited Warranty
This product comes with a 2-year limited warranty that is valid only if
purchased from Reolink Official Store or a Reolink authorized reseller. Learn
more: https://reolink.com/warranty-and-return/.
Terms and Privacy
Use of the product is subject to your agreement to the Terms of Service and
Privacy Policy at reolink.com. Keep out of reach of children.
WiFi Operating Frequency
OPERATING FREQUENCY:
(the maximum transmitted power)
2.4GHz: (For 2.4GHz camera only):
2412MHz — 2472MHz (EIRP < 20 dBm)
5GHz: 5150MHz — 5250MHz (EIRP < 23 dBm)
5745MHz — 5825MHz (EIRP < 14 dBm)
The functions of Wireless Access Systems including Radio Local
Area Networks(WAS/RLANs) within the band 5150-5350 MHz for this device are
restricted to indoor use only within all European Union countries
(BE/BG/CZ/DK/ DE/EE/IE/EL/ES/FR/HR/ IT/CY/LV/LT/
LU/HU/MT/NL/AT/PL/PT/RO/SI/SK/FI/ SE/TR/N O/CH/IS/LI/UK(NI)
Technical Support
If you need any technical help, please visit our official support site and
contact our support team before returning the products,
https://support.reolink.com.
REOLINK INNOVATION LIMITED
FLAT/RM 705 7/F FA YUEN COMMERCIAL BUILDING 75-77 FA YUEN
STREET MONG KOK KL HONG KONG
Product Ident GmbH
Hoferstasse 9B, 71636 Ludwigsburg, Germany
Email: prodsg@libelleconsulting.com
APEX CE SPECIALISTS LIMITED
Addr.: 89 Princess Street, Manchester, M14HT, UK
Email: info@apex-ce.com
May 2023
QSG1_A
58.03.005.0108
@ReolinkTech
https://reolink.com
References
- ce.com
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Official: Security Cameras and Systems for Home & Business
- Reolink Offizielle Website: Überwachungskameras/-systeme für Zuhause & Geschäft
- Sitio web oficial de Reolink: cámaras y sistemas de seguridad domésticos y empresariales
- Sitio web oficial de Reolink: cámaras y sistemas de seguridad domésticos y empresariales
- Reolink officiel : caméras de sécurité pour la maison et l’entreprise
- Reolink Official: telecamere e sistemi di sicurezza per la casa e l’azienda
- Reolink Official: telecamere e sistemi di sicurezza per la casa e l’azienda
- Warranty & Return – Reolink
- Reolink Support - Official Reolink Help Center
- How to Extend the Battery Life of Reolink Battery Powered Cameras
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>