Idaikos A04976W2 Blanche 2 Light Vanity Light Instruction Manual

June 14, 2024
Idaikos

Idaikos A04976W2 Blanche 2 Light Vanity Light

Idaikos-A04976W2-Blanche-2-Light-Vanity-Light-PRODUCT

Instructions Mounting

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instructions carefully and save them as you may need them at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.
  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

FINISHED PRODUCT

IMAGE FOR FINISHED PRODUCT:

Idaikos-A04976W2-Blanche-2-Light-Vanity-Light-FIG-1
\(1\)

TOOLS REQUIRED

TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture

Idaikos-A04976W2-Blanche-2-Light-Vanity-Light-FIG-1
\(2\)

PARTS INCLUDING

  • (C) Green ground screw (1)
  • (D) Mounting plate (1)
  • (E) Backplate (1)
  • (F) Knob nut (2)
  • (G) Socket (2)
  • (H) Iron shade (2)
  • (I) Socket ring (2)Idaikos-A04976W2-Blanche-2-Light-Vanity-Light-FIG-1 \(3\)

ACCESSORIES ENCLOSED

  • (A) Mounting screw (2)
  • (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION

ASSEMBLY & INSTALLATION INSTRUCTIONS:

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
    • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    • Place the wall switch in the “OFF” position.
  3. Make assemblyIdaikos-A04976W2-Blanche-2-Light-Vanity-Light-FIG-1 \(4\)
    • Step A1 » Unscrew knob nuts (F) from mounting plate (D) and back plate (E), then set them aside for later installation.
    • Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
    • Step A3 » Make wire connections Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect Ground

Connect ground wires according to the below chart

Connect wires according to the below chart

Idaikos-A04976W2-Blanche-2-Light-Vanity-Light-FIG-1
\(7\)

Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

  • Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove the back plate (E), and adjust the threaded length of pre- assembled mounting screws on the mounting plate assembly (D):

  • Unscrew the pre-assembled hex nuts.
  • Screw the pre-assembled mounting screws in or out of the mounting plate (D).
  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

Step A5 »

  1. Remove socket rings (I) from sockets (G).
  2. Fix iron shades (H) to sockets (G) with socket rings (I).
  3. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you can turn on the light. Enjoy!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.CLEANING

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

CONTACT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals