Idaikos A04976C3 3 Light Polished Gold and White Modern Contemporary Installation Guide
- August 25, 2024
- Idaikos
Table of Contents
- Idaikos A04976C3 3 Light Polished Gold and White Modern Contemporary
- IMAGE FOR FINISHED PRODUCT:
- TOOLS REQUIRED (NOT INCLUDED):
- PARTS TYPE & QTY INCLUDING:
- ACCESSORIES & QTY ENCLOSED:
- ASSEMBLY & INSTALLATION INSTRUCTIONS:
- ORDERING PARTS
- Product Specifications:
- Product Usage Instructions:
- Frequently Asked Questions (FAQ):
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Idaikos A04976C3 3 Light Polished Gold and White Modern Contemporary
INSTALLATION GUIDE
Item Number: A04976C3
WARNING (To reduce the risk of fire, electric shock, or personal injury):
1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a
later time.
3. Before you start, NEVER attempt any work without shutting off the
electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger
than the canopy on all sides. Any gaps between the mounting surface and canopy
exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before
installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type
B, Max 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging
the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must
wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover
all possible conditions that may occur. It must be understood that common
sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture
PARTS TYPE & QTY INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Canopy (1)
(F) Loop (4)
(G) Quick link (2)
(H) Knob nut (2)
(I) Stem
(J) Iron frame (1)
(K) Tube (3)
(L) Socket (3)
(M) Lampshade (3)
(N) Socket ring (3)
ACCESSORIES & QTY ENCLOSED:
(A) Mounting screw (2)
(B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and
accessories are included as shown in the above illustration.
2. Make pre-installation
Step A1 » Connect stems (I) and then screw stems (I) and tubes (K) into iron frame (J) as shown in the illustration.
- The connecting stems (I) are detachable. The length of the light can be decided according to your preference.
Step A2 » Attach quick links (G) to the loops (F) of canopy (E) and the loop(F) of stems (I) to connect them as shown in the illustration.
3. Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Make installation
Step B1 » Unscrew knob nuts (H) from mounting plate (D) and then remove mounting plate (D) from canopy (E).
Step B2 » Attach mounting plate (D) to the outlet box with mounting screws (A).
Step B3 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
---|---|
Black | White |
*Parallel cord (round & smooth) | *Parallel cord (square & ridged) |
Clear, Brown, Gold or Black without tracer | Clear, Brown, Gold or Black with |
tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other
than green) with silver conductor
-
Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step B4 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (H) onto pre-assembled screws on mounting plate (D).
NOTE: canopy (E) should be snug against the ceiling with knob nuts (H).
If not, remove canopy (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate assembly (D):
- First, unscrew the pre-assembled hex nuts.
- Then, screw the pre-assembled mounting screws in or out of mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B5.
Step B5 »
- Remove socket rings (N) from sockets (L).
- Place Lampshades (M) on sockets (L) and secure them with socket rings (N).
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
5. Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Product Specifications:
- Item Number: A04976C3
- Maximum Voltage: 120V
- Maximum Wattage: Type B, Max 60W per bulb
Product Usage Instructions:
Tools Required:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included:
-
* (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Canopy (1)
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Make pre-installation preparations as shown in the illustration.
- Turn off power before starting the installation.
- Connect wires according to the below chart.
Frequently Asked Questions (FAQ):
Q: Do I need a licensed electrician for installation?
A: It is suggested to have the installation done by a licensed electrician for safety reasons.
Q: What is the maximum wattage per bulb?
A: The maximum wattage is Type B, Max 60W per bulb.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>