BORMANN BBC1250 Automatic Battery Charger Instruction Manual
- June 4, 2024
- BORMANN
Table of Contents
BORMANN BBC1250 Automatic Battery Charger Instruction Manual
Battery smart digital display charger
- LCD display charging current, battery voltage, at any time to understand the status of charging.
- Automatic detection of battery failure, short circuit, negative and positive connected to the reverse lead to failure.
- No need for personnel management, automatic charging, full stop, will not cause overcharging.
- Intelligent charging: PWM microcomputer chip automatically judges the battery status, automatically selects the charging mode, and the charging time is short.
- The energy conversion efficiency is more than 80%, saving more than 30% compared with the traditional charger.
- Wide voltage design 180~260V can be used normally, to meet the voltage instability in some areas can still be used normally.
- Strong adaptability to the battery, battery zero voltage can be charged.
Use of chargers
- When directly charging the lead-acid battery in the car, charge the 12V battery, and the battery voltage will be automatically set to 12V.
- Similarly, when charged with 24V, the voltage is automatically selected on 24V.
- Please remove the original battery cable before connecting the charger for charging.
- The red charging clip is connected to the positive pole of the battery pack +, and the black charging clip is connected to the
- negative pole of the battery pack –
- Connect the charger to the power supply.
- Judge the charging process and result according to the indicator light.
- Rated input: 180-260v AC 50/60 Hz
- Applicable battery specification: 12V/24V lead-acid battery pack
Matters needing attention
This charger aims at the particularity of automobile battery and adds the function of repair and charging:
- This product shall not be used in inflammable and explosive situations.
- The charger is only for indoor use, and it is not allowed to be soaked in water or rain!
- There are high voltage, do not open the shell, children are prohibited to contact!
Performance comparison between traditional battery charger and intelligent battery charger
| Traditional battery chargers | Intelligent charger |
|---|---|
| The first stage | Constant current |
| Charge the battery to 80% capacity | The charger first automatically detects |
the battery and automatically identifies 12V or 24V. If the battery is normal,
it will enter the normal charging mode after 2 minutes and charge the battery
to 80% capacity.
The second stage| Constant current
A large amount of current ACTS on the electrolyte, causing a large number of
bubbles. The voltage shows that it has reached the standard value (Has been
full of), but the actual capacity is still 80%, and since it is still charged
with a large current, polarization phenomenon (overcharging phenomenon) starts
to appear.| CPU microcomputer chip control, automatic from constant current to
constant voltage, small current continue to charge to 95% capacity, avoid
signification phenomenon in the protection plate.
The third stage| Need to cut off the power supply artificially, or it will
appear overcharge phenomenon, shorten the service life of the battery, serious
will lead to battery scrap.| CPU microcomputer chip control, automatically
from constant voltage to constant current, continue to charge to 100% capacity
with small current, complete the whole charging process, automatically stop
charging, there will be no overcharge phenomenon.
Low battery| Such as the battery serious loss of power (over discharge),
direct use of large current charge will damage the plate, even if the voltage
disp has been full,In fact, the virtual power, used for a while on the power,
serously or ten the battery life.| Automatically determine battery status
If the battery is found to be out of power, it will be charged automatically
with a small current until the battery returns to normal, and then charged in
normal charging mode.
This function can protect and repair
the battery, prolong the service life.
Battery failure or improper use| There is no response Damage to battery and
charger.| Sound and light alarm
The charger can automatically detect battery failure, positive and negative
polarity reverse connection, short circuit, battery lack of case and other
phenomena, and sound and light flashing alarm.
Technical Data
| Input: | 220-240VAC 50-60Hz,variable power , 1.5A, , 250W Max |
|---|---|
| Output: | 6VDC, 2A/5A; 12VDC, 2A/5A/10A; 12VDC, 15A, 300s (Boost); Temperature |
Controlled.
Charger Type:| 6 steps, Full-automatic Charging Cycle.
Battery Type:| All type of 12V lead-acid batteries (WET/MF/EFB/GEL/AGM…)
Housing Protection:| IP20
Accessories Included:| Cable Clamps.
Dispose of packing Responsibly.
Do not Dispose of Electrical Goods in Household Waste.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>