BMOSTE 950 Wireless HDMI Transmitter and Receiver User Manual
- June 14, 2024
- BMOSTE
Table of Contents
BMOSTE 950 Wireless HDMI Transmitter and Receiver
Copyright All rights reserved by the product manufacturer.
Dear Customer
Thank you for choosing our product! To ensure optimal usage of this product,
please read this manual carefully before use. This product is intended for
home use only. Before each use, please make sure to check if the equipment is
functioning properly. If any faults occur, please arrange for timely repairs.
NOTES
Please, set 2160p to the (4K output UHD)signal of Interlaced your Scan audio-
video formats devices such as 720i, Progressive 10801 are Scannot: 720p,
supported.
Place the product in an open area without obstruction and avoid covering ii.
Keep away from wireless routers to prevent interference with wireless signal
transmission.
The surface temperature will be high when the product is transmitting 4K UHD
videos. If you need to work continuously for 24 hours, please place the
product in a well-ventilated location.
When the product is used to transmit audio-video signals from laptops or
desktop computers, some computer operating systems may require setting the
HDMI audio-video signal source output.
The Hue, Saturation, and Brightness of the image output by the receiver may
vary across different devices such as televisions and projectors. You can
adjust the HSB parameters according to your preferences.
The product only supports power adapters with a rating of 5V-1500mA or above.
Please note that using a higher-rated power adapter such as 9V or 12V will
damage the product.
Within the same transmission channel, one transmitter can be connected to 2-3
receivers. It supports 2-4 transmitters operating simultaneously in the same
environment using different transmission channels
The transmission distance between the transmitter and receiver is
approximately 250-300 meters without any obstacles.
Transmission distance may be affected when there are obstacles in the path. we
provide a 1-YEAR REPLACEMENT GUARANTEE. Please provide the purchase proof and
product photos when you contact us. If the product you received is defective,
missing accessories or you need technical support,
PLEASE DON’T RETURN IT TO THE STORE.
Contact our after-sales email, and we will be happy to assist you. Global
after-sales service mailbox: SUPPORT@PAKITE.COM
PANEL DESCRIPTION
Transmitter (TX) Panel Description
**Transmitter (TX) Installation
**
Receiver(RX) Panel Description
Receiver (RX) Installation
STARTING UP GUIDELINE
- Press the power switch button of the Transmitter (TX) and Receiver (RX) to turn on.
**Waiting to Connect Successfully
**
- Default transmission channel at the factory: CHN36. After power-on, wait for 22-28 for the Transmitter(TX) and Receiver(RX) to automatically connect and transmit audio and video.
- When there are no obstacles between the Transmitter(TX) and Receiver(RX), the transmission distance is approximately 250-300 meters. The actual transmission distance may vary depending on the environment.
- When using one Transmitter(TX) with multiple Receivers(RX), the transmission distance will be reduced. Please adjust the number of Receivers(RX) according to the actual transmission situation.
WIRELESS IR REMOTE CONTROL
Matching IR Extension Cable
Short press the IR. button to switch the infrared remote control frequency
and match ii with the appropriate device remote control.
Use the IR Forwarding Function
CHANNEL SWITCHING GUIDE
- Channel Switching
Short press the RESET button to switch the transmission channels. (press and hold for 5 seconds to restore to factory defaults) It takes about 5 seconds for the product to re-match after channel switching, so the product restricts the RESET button to take effect every 5 seconds. Please be patient.
Transmission Channel Cycle Sequence
MULTI-TX & MULTI-RX MODE
One Transmitter and Multiple Receivers Mode
One Transmitter(TX) supports connecting with 2-3 Receivers (RX) simultaneously (within the effective transmission distance}. After a successful connection, press the RESET button of the transmitter separately to control the Receiver’s channel switching.
Multiple Transmitters and Multiple Receivers Mode
It supports 9 different transmission channels, allowing the use of 4 sets of
Transmitters(TX) and Receivers(RX) in the same environment without
interference between transmission signals. By short-pressing the RESET button
on the Receiver(RX), you can freely match different Transmitters(TX).
COMPUTER CONNECTION GUIDE
Computer Project Setting
After entering the computer system, press the Windows key CJ and the letter P
key on the keyboard at the same time. The projection menu bar will appear on
the right side of the screen, click “Duplicate”.
Computer Audio Setting
STB CONNECTION GUIDE
Use with STB
sTB Audio Setting
Turn on the setting function of STB and switch HDMI Audio output to LPCM 2
Channel through the Audio setting
Please Support Environment Protection Waste electrical products should not be disposed of by household wants. Please put them to the recyle facilities. Check with your local authority or retailer for recycling advice!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>