SWIT BM-U Series 4K High Definition Monitor User Manual

SWIT BM-U Series 4K High Definition Monitor

PRODUCT INFORMATION

All internal technologies of this product are protected, including device, software, and trademark. Reproduction in whole or in part without written permission is prohibited. All brands and trademarks of SWIT Electronics Co., Ltd. are protected, and other relative trademarks in this user manual are the property of their respective owners. Due to constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice. The warranty period of this product is 2 years and does not cover the following:

• Physical damage to the surface of the products, including scratches, cracks or other damage to the LCD screen or other externally exposed parts.
• The LCD dot defects are not over three.
• Any damage caused by using third-party power adapters.
• Any damage or breakdown caused by use, maintenance, or storage not according to the user manual.
• The product is disassembled by anyone other than an authorized service center.
• Any damage or breakdown not caused by the product design, workmanship, or manufacturing quality, etc.
• Any sales personnel have no rights to provide additional warranty.
  For any suggestions and requirements on this product, please contact us through phone, fax, Email, etc. This manual is applicable to all models of BM-U (5 generation), and the schematic diagram is taken as the appearance diagram of BM-U245. Any specification, appearance, this manual will be additional text description.

Maintenance

Warning:

1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places.
2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio signals.

The power:

1. Please use the power adapter provided or recommended by the manufacturer in order to avoid damage.
2. For a third-party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit.
3. Please disconnect the power cable under the following situations:
   • If you do not operate this monitor for a period of time.
   • If the power cable or power adaptor is damaged.
   • If the monitor housing is broken.

The monitor:

1. Please don’t touch the screen with your fingers, which would probably deface the screen.
2. Please don’t press the screen; the LCD is extremely exquisite and flimsy.
3. Please don’t lay this product on an unstable place.

Cleaning:

1. Please clean the screen with a dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the LCD.

Preface

• All internal technologies of this product are protected, including device, software and trademark. Reproduction in whole or in part without written permission is prohibited.

• All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative trademarks in this user manual are the property of their respective owners.

• Due to constant effort of product development, SWIT reserves the right to make changes and improvements to the product described in this manual without prior notice.

• The warranty period of this product is 2 years, and does not cover the following:

  1. Physical damage to the surface of the products, including scratches, cracks or other damage to the LCD screen or other externally exposed parts;
  2. The LCD dot defects are not over three;
  3. Any damage caused by using third-party power adaptors;
  4. Any damage or breakdown caused by use, maintenance or storage not according to the user manual.
  5. The product is disassembled by anyone other than an authorized service center.
  6. Any damage or breakdown not caused by the product design, workmanship, or manufacturing
     quality, etc.

• Any sales personnel have no rights to provide additional warranty.

• For any suggestions and requirements on this product, please contact us through phone, fax, Email, etc.

• This manual is applicable to all models of BM-U (5 generation), and the schematic diagram is taken as the appearance diagram of BM-U245. Any specification, appearance, this manual will be additional text description.

Maintenance

Warning

1. In order to reduce the risk of fire and electrical shock, do not lay this product in rain or damp places.
2. Please keep away from the strong magnetic field; it may cause the noise of the video and audio signals.

The power

1. Please use the power adapter provided or recommended by the manufacturer in order to avoid damage.
2. For a third party power adapter, please make sure the voltage range, supplied power, and polarity of power lead are fit.
3. Please disconnect the power cable under the following situations:
   • If you do not operate this monitor for a period of time;
   • If the power cable or power adaptor is damaged;
   • If the monitor housing is broken.

The monitor

1. Please don’t touch the screen with your fingers, which would probably deface the screen.
2. Please don’t press the screen; the LCD is extremely exquisite and flimsy.
3. Please don’t lay this product on unstable place.

Cleaning

1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the LCD.

Packing list

1. Monitor X 1
2. Warrantee card X 1
3. Battery plate（V-mount or Gold-mount) X 1
4. Tabletop stand X 2
5. Power cord X 1

Introduction

This series of monitors adopt TFT-LCD panel, the resolution is up to 3840×2160, H178° / V178° ultra-wide viewing angle, supports 4 x 12G/6G/3G/HD /SD-SDI, 1 x HDMI® 2.0 4K@60 with 4 x 12G/6G/3G/HD/SD-SDI loop outs with headphone and speaker outputs.

Features:

• 3840X2160 Ultra HD，（※ BM-U315/BM-U316 Ultra 4096X2160）
• 4K/UHD interface（4x12G-SDI input，4x12G-SDI output,1x HDMI® 2.0 4K@60 input）
• 16ch audio bar display, with any selected 2ch output
• Support waveform selection display Y/Cb/Cr/R/G/B /RGB and single line selection mode
• Vector scope, R/G/B/Y histogram, bi-color focus assist
• 3DLUT（17 x 17 x 17） accurate color correction
• Dynamic UMD and TALLY(TSL3.1, 4.0) display
• Composition ratio auxiliary line:4:3/13:9/14:9/15:9/16:9/1.85:1/2.35:1/2:1/1.39:1/Custom1/ Custom2
• Support USB firmware upgrade and import Log file.(USB file system supports FAT 32 format only)
• Eco mode

Product instructions

Front panel

1. Speaker: For SDI/HDMI® embedded audio. (Will not work if earphone is plugged in)
2. Desktop Stand Feet
3. User1~User4: User shortcut key, which can be used to quickly enter the set user mode. Long press to save user settings. Please see details in“ 9. System”
4. Info/Quit: Display setting item. Press ” Info/Quit ” button to display or turn off relevant status information and audio and video analysis function graph. When opening the menu, press ” Info/Quit ” to exit the menu with one click
5. F1~F5 function keys: Customize shortcut function keys. Users can set the shortcut keys to different functions according to their own requirements.
6. 
   • Brightness: Adjust the brightness. -100~100 adjustable, default value is 0.
   • Contrast: Adjust contrast. -100~100 adjustable, default value is 0.
   • Saturation: Adjust saturation. -100~100 adjustable, default value is 0.
   • Backlight: Adjust the backlight. 0~100 adjustable, default value is 16. (The default backlight value of BM-U245 is 35.) Press Brightness, Contrast, Saturation, Backlight, Volume five shortcut keys confirm to select this option, and rotate Menu to adjust the corresponding item value directly. Press the button and automatically cancel the selection without operation within five seconds, and the button light will be off, long press to restore default values.
   • Volume: Adjust the volume.0~100 adjustable, the default value is 36.Long press the volume button to mute.
   • Source: Select the input source signal format. As shown in the figure above, when Multi-screen is selected, the screen is divided into 4 frames, and 4 channels of SDI signals can be displayed simultaneously. When Four-screen is opened, some menu functions are turned off or displayed in gray.
7. Menu/Enter： When no Menu is displayed, press the button directly to open the Main Menu; Rotate the knob to select different settings or adjust parameter values, press the knob to set.
8. LUT/Firmware: Update firmware or import LUT files，Auto Calibration.
9. PHONE: 3.5mm headphone jack is used to monitor the embedded audio signals of SDI and HDMI.
10. Power: Power switch.
11. Tally lamp: You can select the color of the tally lamp from“ Green”“, Red”, or“ Yellow”

Rear panel

1. SFP IN: Optical fiber interface
   12G/6G/3G/HD/SD-SDI video signal fiber input interface
   Fiber optic module is optional

2. SDI IN1~4： 12G-SDI

3. SDI OUT1~4： 12G-SDI

4. ETHERNET: Network interface 1000M high-speed RJ45 Ethernet port, for web server IP external control.

5. HDMI® 2.0 4K@60 IN ：
   Will not display HDCP protected content.

6. RS485: TSL UMD control port

7. GPI: GPI control port

8. Fan

9. VESA bracket mounting area

10. DC IN: 12V~17V

11. AC IN: 100V~240V

12. AC switch: Used to directly turn on or off AC power supply
    BM-U175/BM-U245/BM-U245HDR supported DC, AC and battery powered three types of power supply. BM-U275HDR/BM-U315/BM-U325/BM-U325HDR/BM-U316HDR AC power supply only.

OSD

1. Time code（SDI）
   Under SDI input, the monitor can display Time code information (LTC, VITC1&2). If no Time code info is detected, it will display“ TC UNLOCKED”. User can set function keys F1～F5 or GPI pins as “Time Code” to turn on or off this function.

2. On screen TALLY
   Display TALLY signal from GPI port.

3. Source ID/UMD
   Display TSL 3.1/4.0 UMD or User input Source ID.

4. Colour gamut chart
   Displays the current video colour gamut, which can be set by the user in the “Main Menu” – “Colour Management” – “Colour Gamut

5. Lissajous
   Lissajous diagram showing audio signal. Users can set the shortcut keys (F1～F5) or GPI pins on the front panel to“ Lissajous” function and turn it on/off.

6. Waveform
   The display waveform can be selected from Y/Cb/Cr/R/G/B/RGB types, and single line display mode selectable. The waveform display positions, colors, background are adjustable. User can set function keys F1～F5 or GPI pins as“ Waveform” to turn on or off this function.

7. Vector
   Display vector scope with 100% and 75% markers for SDI and HDMI® video. The vector scope pattern display positions, colors, background are adjustable. User can set function keys F1～F5 or GPI pins as“ Vector” to turn on or off this function

8. eye pattern
   Tests the quality of the SDI signal, the larger the eye pattern, the stronger the quality.

9. ColorChecker
   After auto calibration, the color gamut and chromatic aberration (△E“) Automatic colour correction”“- Start colour proofing” and “Auto Calibration” – “Measure” pops up the gamut value and color difference value (△E) of the previous calibration and this measurement.

10. Histogram
    Parallel display R/G/B/Y histogram for SDI and HDMI® video. User can set function keys F1～F5 or GPI pins as“ Histogram” to turn on or off this function.

11. Audio VU/PPM meters
    Display meters of SDI/ HDMI®embedded audio or analog audio. The audio meter display channels, on screen positions, markers and background colors are adjustable. User can set function keys F1～F5 or GPI pins as“ Audio Bar” to turn on or off this function.

Status display

Press“ Menu/Enter” button, the main menu will pop up from the left top of the screen.
The main menu displays the current working status of the monitor.

1. Format
   A format for displaying the current input signal, if there is no currently identifiable signal input, display “no Signal”. When Four-screen is selected for the current channel, the input signal standard of SDI 1/2/3/4 orSDI 1/2/3/HDMI® channel is displayed in standard.

2. Source
   Displays the currently selected channel

3. Color Temp
   Displays the currently set color temperature mode

4. F1~F5
   Displays the function value set by the current function key

5. Profile Type
   Displays the currently set scan mode

6. Version
   Displays the current software version number

Key configuration.

Steps

1. Press“ Menu/ Enter” button, the main menu will pop up from the left top of the screen. The selected main menu highlights in yellow .

2. Revolve“ Menu/ Enter” to select submenu, the selected submenu highlights in yellow, press“ Menu/ Enter” to apply and enter into the selected submenu’s items.

3. Revolve“ Menu/ Enter” to select the item which needed to adjust, press“ Menu/ Enter”, the selected item and its parameters will be highlighted in yellow

4. Revolve“ Menu/ Enter” to change the selected item’s parameter, press“ Menu/ Enter” to apply and save the settings.

5. Revolve“ Menu/ Enter” to select“ Exit”, press“ Menu/ Enter” to quit submenu. Select“ Exit & Status” under the Main Menu and press to quit Main Menu
   Notice

   • The items in gray cannot be set up
   • If there is no operation under the set time, the menu will automatically save settings and quit.
   • If the key inhabit function is turned on, except System menu, all other items are in gray. Please turn off the key inhibit function to adjust the items.

Menu Configuration

Menu configuration introduces the main menu and each sub-menu. Menu items marked * will give more detailed menu description or operation explanation after the list

Input ‒ Set the color of input video

1. Input range
   Set the video input range to fit the input video signal. The default video input range is 64-940 for broadcast applications. The quantization range of each SDI or HDMI® channel can be individually adjusted for display when multi- screen, multi-colour gamut is selected.

*Image 1—Setting for the picture preference**

1. Image
   Contrast, brightness, saturation and backlight can be quickly adjusted by the front panel shortcut keys

Color management—Settings about video colors

1. Color Gamut
   Set the gamut to match the input audio. When Multi-screen，Multi-colour gamut, the color gamut value of the 4-channels SDI or HDMI® signal can be adjusted separately for display.

2. .Gamma
   When Four-screen is selected; the gamma of 4 channels SDI or HDMI®signal can be adjusted separately for display.

3. HLG System Gamma
   Display tunable only when Gamma is set to HLG1000

4. D-Log to 709
   Display tunable only when color gamut is set to Rec.709 mode and Gamma is set to a value.

5. Partition HDR/SDR
   Individual colour gamut for Partition HDR/SDR, gamma can be adjusted individually, Partition HDR/SDR default colour gamut Rec.2020, gamma 2.2.

6. LUT Upload
   Place the cube file that needs to import the monitor in the root directory of the u-disk, insert the u-disk into the USB interface on the front shell of the monitor, and choose to import the corresponding file.

Scanning—Setting for picture scan, zoom, etc.

1. Scanning Mode
   Panel Fit: Turn on this feature to adapt the video to the entire screen. Original scan：Original scans can be displayed at 4096, NTSC, PAL resolutions.

2. .Zoom -in: Shown below, the image is divided into 9 regions and adjusted to display in sequence.

When the zoom mode is turned on, a rectangle box pops up at the bottom left of the screen, showing the currently selected zoom image area, Zoom mode on, image still frame hidden, Freeze Frame, Zoom mode function is turned off.

3. .Odd/Even Frame
   Odd/Even Frame is only displayed in I mode. Open Low Latency Mode and Zoom Mode , Freeze Frame ,Odd/Even Frame function is turned off.

Control—Setting for TALLY, UMD, IP control to the monitor

1. GPI control

   • Connect the GPI remote control terminal through the GPI interface on the real panel of the monitor, turn on“ GPI control” and set the function of GPI 1-6 buttons

   • The GPI control allows you to control both the Tally light and the on screen TALLY light on at the same time:

2. UMD
   Select the display type as“ “TSL3.1 or 4.0”, which can be controlled with TSL UMD. When selecting multiple images,each SDI or HDMI®can be displayed separately.

3. **Cascade:

**

Assist— Setting for Vector scope and Histogram patterns.

1. WFM Single Line
   Open waveform single-line mode, the monitor shows only one line of audio waveform. Rotate the Menu/Enter knob to select the number of lines of audio signal to display the waveform. (The selection range of the number of lines in a waveform depends on the current signal standard)

2. Horizontal / Vertical
   When marker select is USER 1, Users can adjust the X position and Y position of the marking line according to their own needs，Coordinate value is adjustable from 50% to 99%；when marker select is USER2，the value of X-axis is adjustable between 0~3840，the value of Y-axis is adjustable between 0~2160.

3. Eye Pattern
   HDMI® channels do not display eye diagrams.

De-embed— Setting for video/audio analysis functions.

1. Audio Meter Marker
   • Audio table display, display 16 channel audio table
   • Marking line off: Only the audio table is displayed
   • Marking line on: Display audio decibels, audio alarm signal and left and right channel options.

2. Left and right channel
   When opening four-screen, the audio bar only displays four channels of sound channel is used to select the sound channel shown in the audio bar.

3. Timecode
   Time code is not displayed on HDMI® signals

4. H/V Delay
   H/V Delay is not displayed with HDMI® signals

*Auto Calibration1**

1. Auto Calibration
   The monitor has 3D LUT calibration software built-in, and supports the following color sensor probe to directly plug into front USB port. When start calibration, the monitor will generate standard colors and the color sensor will read the colors one by one and upload result to the monitor by USB connection. The monitor will comparing the generated colors and sensor read colors, to work out 3D LUT cube and calibrate itself automatically.

2. .Probe Select
   This monitor supports the following probes models:

3. Start Calibration
   Steps:

4. Put the monitor into a dark room. Switch on the monitor.

5. Connect the calibration instrument (compatible with x-rite and JETI color measuring instru ments) and monitor via USB. Before calibration, ensure that the monitor and the color cali bration instrument are in good condition and the monitor aging time reaches 30 minutes.

6. Enter the“ Probe Select” and select the currently used calibration probe.

7. Enter the“ Start Calibration” and select“ YES” to start calibration. The monitor will display the prompt message and the color position prompt box. Put the sensitive part of the device in the color position prompt box correctly. Note that when placing the calibration instrument; do not squeeze the monitor’s LCD screen

5. Select ” YES ” to begin auto calibration. The color calibration instrument will automatically mea sure the color of the screen and correct the color of the screen. During this process, it is necessary to observe the color calibration progress bar in the color correction prompt box.

6. Press “Info/Quit” to terminate the color correction process at any time. When the prompt color calibration progress reaches 100%, the whole automatic color calibration is completed. After automatic color correction, press the ” Info/Quit ” button to exit the menu and let the monitor enter the normal display mode.
7. After the automatic color correction, the display screen pops up“ Before Calibration” and“ After Calibration”

4. Measure
   • The monitor has been calibrated in factory. And may need to be re-calibrated after a period of time.
   • Before re-calibrated, the measure function can check the current color to compare with the last time calibrated color, to decide if the monitor needs to be re-calibrated.
   • Connect with the sensor probe and place the sensor probe onto the right position like calibration step. Enter“ Auto Calibration” ‒“ Measure”.
   • The monitor will generate several colors and finish measure within 30 seconds. And display the result as：

System— User profile saving, firmware update.

1. Key Lock
   The“ Menu/Enter” button can be operated when the button is locked“. Key Locked” will be displayed on the screen when you press the Locked button or knob.

2. Recall Profile/ Save Profile
   User Settings provide 4 menu Settings, that is, users can save the current monitor menu Settings as one user Settings (USER1~USER4) according to usage habits. Then, when switching menu Settings, just select the corresponding “USER1~USER4” through the“ Recall Profile” item to display the corresponding menu Settings.
   Example：By adjusting the parameters of the color temperature of 2200K, open the necessary auxiliary functions (such as: histogram), set the function key to the desired menu (such as F1 is set to “Blue Only”), and so on, the monitor Menu Settings can be “USER Settings” save as “USER” 1, rotating the“ Menu/Enter” choose to load the USER Settings “set to the current” USER 1 “mode, the monitor Menu item value will show” USER 1 “mode to save Menu.

3. Low Latency Mode

   • Low Latency Mode is a special image processing mode for lip-sync monitoring.
   • For progressive (p) formats, the monitor is low latency itself, whether low latency mode is on or off. For interlace (I) or progressive segmented Frame (psd) formats, turn on Low Latency Mode will get lower latency.

4. IP control
   • Connect the monitor to the LAN through an ETHERNET interface, and the Monitor can be controlled by web page.

  * Enter Menu- System ‒ IP/Net Mask/Gateway/Port to set the monitor address. Set the computer
  * Ethernet IP addresses at the same LAN environment as the Monitor.
  * Launch any of a web browser on the computer, and enter URL: Monitor IP+ Port (Example: 192.168.1.99.8080). The web server control page will be displayed.

  * Used crossed wired cable for computer-monitor directly connection.
  * Use straight-through wired cable for Router connections.
  * Please seek help from your webmaster for any network connections.

5. .Update
   System software can update by USB interface, and steps are as follows:

6. Download the latest software package into the U-disk root direction.

7. Open the monitor and plug U-disk into USB into port.

8. Follow the step“ Menu-System“, the monitor will update automatically.

9. When update finishes, press“ Power” button, close and reboot the monitor.

Remark

  1. Only copy one model and software version into the U-disk root direction.
  2. Never shutdown the power during the update progress.  

**Webserver page control interface

**

*Multi-screen settings 1**

1. Multi-screen settings
   • Selecting the button Source in Multi-screen for the Multi-screen settings to be adjustable; some menus are hidden in Multi-screen;
   • When Multi-screen is selected for the channel, the quantization range, colour gamut, gamma, UMD and
   • Payload ID of each screen can be adjusted separately.
2. Multi-screen type
   If there is no signal on the 4th SDI channel input, an HDMI® signal appears on the 4th channel.

Size

Monitor（unit：mm）

• BM-U175, BM-U245 ,BM-U245HDRhas battery plate in the back, support battery powering.
• BM-U175, BM-U245 ,BM-U245HDRcan install 100*100 pitch-row VISA bracket.
• BM-U275HDR, BM-U315, BM-U325,BM-U325HDR,BM-U316HDR can install 100100 or100200 pitch-row VISA bracket.

Specification

Supported Format： Signals below can display on the monitor

Trouble-shooting

ABOUT COMPANY

• SWIT Electronics Co., Ltd.
  • Add: 10 Hengtong Road, Xin’gang, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.China
  • Tel: +86-25-85805753
  • Email: contact@swit.cc
• SWIT Electronics Europe GmbH
  • Add: Hochstr. 17, 47228 Duisburg, Germany
  • Tel: +49(0)20659799339
  • Email: info@swit-europe.com
• SWIT Electronics America, Inc
  • Add: 3350 Scott Boulevard 61-02, Santa Clara, CA 95054, USA
  • Tel: (408)260-8258, 1-866-986-SWIT(7948)
  • Email: info@swit.us
• SWIT Electronics Co., Ltd.
  • Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.China
  • Phone: +86-25-85805753
  • Fax: +86-25-85805296
  • Email: contact@swit.cc
  • http://www.swit.cc

References

• SWIT Global Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>