boifun J1 Wi-Fi Smart Wireless Video Doorbell Camera User Manual

boifun J1 Wi-Fi Smart Wireless Video Doorbell Camera

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If it not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
(FCC ID: 2AUSP-BELL)

After-sale support

Thank you for purchasing our BOIFUN smart video doorbell. We provided 24 months warranty. If you have any problems or suggestions, please feel free to contact us by Amazon message or send e-mails to our official mailbox ([email protected]). The best service will be offered to you.
Note:

• The smart video doorbell only supports 2.4GHz Wi-Fi, it doesn’t support 5GHz Wi-Fi.
• Pay attention to the positive and negative poles of the battery when installing and removing the battery to prevent explosion.
• The battery is model 18650.
• Please ensure that the Wi-Fi signal strength is to be over than 75%; if the smart video doorbell is far away from the signal source, it won’t be connected successfully for the first time.
• If your router is connected with too many devices, the smart video doorbell will fail to connect Wi-Fi because of the IP address conflict.
• This smart video doorbell does not support PC Browser and Software.
• This smart video doorbell supports events recording when Wi-Fi disconnected.
• Video playback works in BoifunCam APP only. It does not support the 3rd party player.
• Manually snapshot and recording files are saved in mobile. Events snapshot files are saved in Cloud. Events recording files are saved in Micro SD card.
• It will consume the batteries power if you watch live footage or the recorded videos in APP from the SD card.

What’s in the box

Please consult below checklist for all the components.

Meet the doorbell

1. 3MP camera
2. PIR
3. Speakers
4. Doorbell button
5. LED indicator
6. Base switch
7. Built-in 18650 battery
8. Micro-SD card slot
9. Reset button
10. Micro-USB port

Meet the chime

1. indicator LED
2. Reset
3. Volume
4. Ringtone
5. Speaker

Battery charging

• The batteries inside the doorbell are not fully charged in accordance with transportation safety regulations.
• Please charge the batteries with a USB-compatible wall charger (not included) and the provided
• USB cable for about 8-10 hours prior to installation. Battery management:
• The battery life depends on the activated frequency. Here are some simple settings to avoid

Battery management:

• The battery life depends on the activated frequency. Here are some simple settings to avoid unnecessary power loss:

1. Set the recording time to normally 20-30s which is enough for daily needs.
2. It is recommended to lower the “Motion Detection” sensitivity or open the “Human Motion Detection” function.
3. When the doorbell is facing the main road, it is recommended to adjust the angle of the doorbell to avoid unnecessary activation.
4. Make sure the Wi-Fi signal strength is over 75%, if it’s lower than 75%, the doorbell will be continuously activated. Install the camera close to the router or add a Wi-Fi extender to improve the Wi-Fi performance of the house. If you tried and still can’t solve the issue, please feel free to send email to [email protected]

Download the app

• Download and install the “BoifunCam” App from Google PlayTM or the App StoreTM.The App is also available by scanning the QR codes, using your QR code scanner on your smartphone.

Note:

• Google PlayTM is a trademark of Google Inc.
• App StoreTM is a service mark of Apple Inc.

Note:

• A very small number of mobile phone models may not be compatible with BoifunCam.We apologize for any inconvenience this may cause. If you encounter this situation, could you please send us your phone model by email? Our email address is [email protected].We will optimize the software in time, and we have prepared a backup software “CloudEdge” for you, which you can download and use from the Google Store or Apple Store. We would greatly appreciate your understanding and kindness!

Wi-Fi set up

Tips for setting up:

1. Make sure the device is within 10 meters or 30 feet range of your router.
2. Check if your router is up and functioning, and perform the configuration near your Wi-Fi router.
3. Check that your device is away from any devices that cause interference (such as microwaves, baby monitors, or other electronic devices).
4. If you have separate network names for the 2.4 GHz and 5 GHz bands, please make sure you are connected to a 2.4 GHz network.
5. Avoid using special characters or symbols like)(@-!#$%”& …, either in your Wi-Fi name or password. If your issues haven’t been solved, please feel free to send an email to [email protected].

Guiding steps:

1. Tap to add the device
2. Select Doorbell
3. Check power status
4. Activate the doorbell
5. Reset device
6. Input Wi-Fi password
7. Prepare Code Scanning
8. Generate QR Code
9. Wait for connection
10. Adding device complete

Run a test

After setup, tap on the live view window in the App for a test. Then take your doorbell outside to the installation spot and run a test there. Make sure the installation spot is covered by a strong 2.4 GHz Wi-Fi signal.
Note:
If the video quality from the doorbell outside is not as good as it was indoors, you may need to move your router closer to your installation spot or invest in a Wi-Fi extender.

Live viewing

1. Quit live viewing
2. Setting menu
3. Volume on/off
4. HD/SD switch
5. Full-screen display
6. Stream bit rate
7. Wi-Fi signal status
8. Battery status
9. Photo Album
10. Video Playback
11. Screenshot button
12. Speak to the visitor
13. Voice Changer (Original, Clown, Uncle)
14. Cloud storage service
15. Record on the phone
16. Motion Detection on/off
17. Siren

Note: Live viewing will not trigger video recording.

Playback
If the Micro-SD card is properly installed, JOU can play back the video clips taken after detected motions or visitor calls. (Live viewing will not trigger device recording) You can also back up video clips to the cloud, but only if YOU have activated the cloud storage service (7-day free Trial available).

Leave voice messages

• Maximum 3 voice messages (Max. 10 seconds each) can be pre-recorded into the doorbell, which enables you to quickly respond to your visitors when you are not convenient to answer the doorbell call.
• Steps: Setting – > Voice Message -> Press and hold this icon to record voice messages –> Push the doorbell button –> Play the selected voice message in reply to the doorbell call.

Share your device

Sharing my account searching

• Steps: Settings>>Device Share»>Tap on “Add” »›Tap on “Account” »>Type in account ID>> Confirm Sharing.

Sharing by QR code scanning

• The new users can show their QR codes to the administrator, and share devices by QR Code scanning.
• Find your OR code: Run the BoifunCam App » Tap on » “User Name” » “My OR Code” »> Let the administrator scan your QR Code.

Note:

1. Guide your family members to download and install the BoifunCam App, and register an account prior to device-sharing.
2. There is no limitation on the number of users sharing one device.
3. Only the administrator got access to the settings menu. Other users can only live view & playback.
4. All users will receive doorbell calls and alarm notifications.
5. Many users can access the doorbell simultaneously, to live view or playback.

Connect the chime

1. Power the chime
   • The chime is powered by 3 units of AAA 15V battery.
2. Click reset button
   • Click the RESET button on the wireless chime only once, and you will see the LED indicator flashing blue, indicating the chime is in pairing mode.
3. Press the doorbell button
   • Press the doorbell button, and the Chime will sound to react.
   • Pairing succeeds, and the indicator on the chime will be in solid blue.
4. Chime settings
   • You can enter the chime setting page following the below setting steps, so as to mute the Chime Reminder, select ringtones, adjust the chime volume, or unbind the connection with the doorbell.

Note:

1. Your doorbell communicates with the chime via Radio Frequency, but not Wi-Fi. You can even do the pairing prior to the doorbell configuration.
2. You can add many chimes to one doorbell, and vice versa.
3. Press and hold the RESET button on the chime for 5 seconds till the indicator flashes blue 3 times, and you can also release the connection between the chime and its connected doorbell.

Installation

Select location

• Your doorbell has a 166-degree view angle and a 120-degree human detection range.
• It is suggested to mount your doorbell at least 5 feet (160 cm) above the ground for the best angle of view and motion detection performance.

Go wireless installation

1. The doorbell can be removed by poking the base switch at the bottom.
2. Bracket installation: mount the bracket on the wall with screws & anchors or double-sided adhesive tape.
3. Mount your doorbell to the fixed bracket. Make sure it reaches the bottom where you can hear a click.
4. All set, congratulations! Now you can press the doorbell button to try it out.

• Please fully charge (about 8 hours) before the first use.
• Lab-tested battery life: 12-month standby, 6 months regular using activate 20 times per day.
• (The actual battery life may be different due to different activation frequencies).

Specification

Video Doorbell

Indoor Chime

FAQS

Q1: Why did I fail to set up Wi-Fi for the doorbell?

1. A: The device works with 2.4GHz Wi-Fi only, but does not support 5GHz Wi-Fi.
2. The Wi-Fi network is not good, try to keep the camera near the Wi-Fi router when setting up.
3. The Wi-Fi password is wrong. Please check if there are special characters in the password, or if the network is specially encrypted.

How to improve the battery life performance?

A2:

1. Set the recording time to normally 20-30s which is enough for daily needs.
2. It is recommended to lower the “Motion Detection” sensitivity or open the “Human Motion Detection” function.
3. When the doorbell is facing the main road, it is recommended to adjust the angle of the doorbell to avoid unnecessary activation.
4. Make sure the Wi-Fi signal strength is over 75%, if it’s lower than 75%, the doorbell will be continuously activated. Install the camera close to the router or add a Wi-Fi extender to improve the Wi-Fi performance of the house.

Q3: How do I know if I have 2.4G or 5G Wi-Fi?

• A3: Please check the user manual of your router or call the network operator for help.

Q24: It have to be on the same Wi-Fi to see the camera, or is it over the internet from anywhere?

• A4: You can view the camera from anywhere if your camera is well connected to the internet.
• Q5: Do any of the recordings get saved to the cloud? Or is it mainly saved in the built-in SD card?
• A5: It supports SD card recording as well as cloud storage. You can activate the cloud storage service in the App.

Q6: What happens when the SD is full?

• A6: When the memory card is full, the camera automatically erases the oldest footage.

Q7: Does it work with Google Home or Alexa?

• A7: Sorry, this model does not support Google Home or Alexa.

Q8: Why does it lose connection to Wi-Fi?

• A8: Please check the network connection of your phone and the Wi-Fi router. If the network signal strength is lower than 75%, the doorbell will be continuously activated.
• Install the camera close to the router or add a Wi-Fi extender to improve the Wi-Fi performance of the house.

Q9: Can motion detection be disabled?

• A9: Yes, sure. The recording is triggered by detected motions. You can set up the sensitivity or disable motion detection in the settings menu.

Q10: Do we get a charger for the batteries?

• A10 : Battery charger is not included. Please charge the batteries with a USB-compatible charger(DC5V 1A-2A) for about 8-10 hours.

Q11: Can we have 2 or more doorbells at the same residence?

• A11 : Yes, you can add more than one device at the same residence.

Q12: If I have other questions, what can I do?

• A12: If you encounter any other problems, please send your order and problem to [email protected].
• www.boifun.net
• Social Media

Documents / Resources

| boifun J1 Wi-Fi Smart Wireless Video Doorbell Camera [pdf] User Manual
J1 Wi-Fi Smart Wireless Video Doorbell Camera, J1, Wi-Fi Smart Wireless Video Doorbell Camera, Smart Wireless Video Doorbell Camera, Wireless Video Doorbell Camera, Video Doorbell Camera, Doorbell Camera, Camera
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>