boifun C12C1vjJK8L Wifi Video Baby Monitor Camera Instruction Manual
- June 14, 2024
- BOIFUN
Table of Contents
boifun C12C1vjJK8L Wifi Video Baby Monitor Camera Instruction Manual
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Responsible for compliance could void the user’s authority to operate this
equipment.
(Example- use only shielded interface cables when connecting to computer or
peripheral devices).
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and;
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
FCCID: 2AG7C-BABY1M (Monitor)
FCCID: 2AG7C-BABY2T (Camera)
After-sale Support Dear friends,
Thank you very much far supporting BOIFUN !
If you have any issues, please email your order number and the problem to
[email protected]. Receiving your message, we will provide a fast solution in
24 hours. Please do not worry. Actually, many problems can be easily solved by
setting, such as Battery Management, Networking Connection Fails, VOX mode,
Alarm sound too loud, etc.
If you have any questions or ambiguities during using, please feel free to
contact us. We will try to find a good solution with our professional
engineers, and reply you in 24 hours.
Warm Regards
BOIFUN Service Team
http://qr.hotlnk.cn/url/79829115556
What’s in the box
Please consult this checklist for all parts.
Description
Installation
- Install the camera on a flat surface.
- Or use the included mounting bracket to fix the camera to a clean surface.
Connection
1. Connect the camera to the display
Power on the camera and the display and then the camera will connect to the
display automatically.
Note: If the connection to each other is not successful the first time, press
and hold the reset button on the back of the camera and reconnect the monitor
after the second beep of the camera. The connection is distance limited, so
make the distance between the camera and the display is no more than 1000ft.
Disconnect the camera to the display:
1. Press Menu button on the display screen, and select > Camera Management.
2. Long press the OK button on the display screen to release the binding.
Reconnect the camera to the display:
- Press the Menu button on the display screen, and select > Camera Management.
- Long press the camera pairing button until you hear the prompt tone.
- Press the OK button on the display screen to start pairing.
NOTE: If you have problems with connection, please feel free to contact [email protected] for one-on-one customer service guidance.
2. Connect the camera to the App
The camera can be connected both to the display and the App. Generally, it is
connected to the display by default.
Follow the steps below to connect the camera to the App:
- Make sure the Wi-Fi network is a 2.4 GHz network, as the camera doesn’t support 5 GHz Wi-Fi.
- Download the Boifun Cam App on your phone. Register a new account to log in or log in directly.
- Press the Reset button far five seconds until you hear the “BOOGU” beep, which means the camera has been reset, after 10-20 seconds, you will hear another beep and the red light of the camera blinks slowly.
- Follow the step instructions on your smartphone to add the cam, and scan the QR code with your camera.
General Setting
Set up volume:
- Press Menu button on the display screen, and select ? and press OK to enter the interface.
- Press UP and DOWN direction buttons to adjust volume.
2. (Optional) You can format the SD card as you needed, but make sure that
the important data is backed up.
NOTE: This product does not support hot-swapping. Please insert the SD card
before power on or unplug it after power off Please format the sd card into
FAT32 format before using it
-
Upgrade:
Make sure your camera is connected to a 2.4 GHz Wi-Fi.
You can upgrade your camera when the upgraded alarm appears. Or Press Menu button on the display screen, and select > Device information to check whether there is an upgrade. -
Low battery alarm:
When the camera is low on battery, the low battery alarm will appear on the display screen. Please charge the display as soon as possible.
Usage
- Download
BoifunCam is available for both iOS and Android OS. Search the name “BoifunCam” in App Store or Google Play or scan the QR-Code to download the App.http://qr.hotlnk.cn/79847667793
Note:
A very small number of mobile phone models may not be compatible with
BoifunCam.
We apologize for any inconvenience this may cause. If you encounter this
situation, could you please send us your phone model by email? Our email
address is [email protected]. We will optimize the
software in time, and we have prepared a backup software “CloudEdge” for you,
which you can download and use from the Google Store or Apple Store. We would
greatly appreciate your understanding and kindness!
-
Add device
Log in the BoifunCam, select “Add Device”. then select baby monitor and add the smart camera to the App according to the screen tips (Make the smart camera close to the router when configuring).
NOTE: -
If you have problems with BoifunCam. please feel free to contact [email protected] for one-on-one customer service guidance
-
If you need to re-select the WiFi network. please press and hold the “RESET” button for 5 seconds. the device will restart. and the indicator will be flashing red.
-
Rotate the camera
You can adjust the monitoring angle for better vision.
The direction buttons on the display screen are available when the camera is powered on.
Press direction buttons to rotate the camera horizontally and vertically for a better vision. -
Photo & video
-
Play music
You can play music to soothe your baby when the baby is crying or sleeping. A variety of soft music is available.
-
Feeding reminder
Remind yourself to feed your baby, when you are too busy, or when you want to give your baby a regular diet -
Press the Menu button on the display screen. and select > Feeding reminder.
-
Press UP and DOWN direction buttons to select between 4 time options and press OK to start time setting.
-
When start to set up one feeding time. press LEFT and RIGHT direction buttons to change options between hour. minute. second and on/off; and press UP and DOWN direction buttons to change values and select on or off.
-
Press OK to save settings.
-
Select on or off to open or close feeding reminders.
You can set up to 4 feeding times one day. And when the set time is up, a feeding alarm will appear on the display screen.
-
Humiture detection
You can real-time monitor the temperature and humidity of your baby room.
When the temperature and humidity are out of range, you can get the alarms immediately, and then take measures. -
Press the Menu button on the display screen. and select > Humiture detection.
-
Press UP and DOWN direction buttons to select options between temperature range, humidity range and out of range reminder. and press OK to start setting.
-
When starting to set up one option. press LEFT and RIGHT direction buttons to change options. and press UP and DOWN direction buttons to change values and units.
-
Press OK to save settings.
-
In Out of range reminder option. select to turn on or off the alarm when the temperature and humidity are out of range.
-
Optional Access Channels
You can turn on or turn off the Wi-Fi network channel so that others cannot live view the videos by App if the function is off. And you can also view the visited records as all visits through the App will be recorded.
-
Smart care
You can turn on functions of motion detection. noise detection and cry detection. so that you can know the baby status immediately, no matter you are sleeping, working, cooking and so on. -
Press the Menu button on the display screen and select > Smart care.
-
Press UP and DOWN direction buttons to select options between motion detection. noise detection, cry detection and alarm volume, and press OK to start setting.
-
When starting to set up one detection mode. press LEFT and RIGHT direction buttons to change options. and press UP and DOWN direction buttons to adjust the sensitivity.
“‘You can select different sensitivity according to needs. Low is low sensitivity, and high is high sensitivity. -
When setting up the alarm volume. press LEFT and RIGHT direction buttons to adjust.
-
Press OK to save settings.
-
There will be an alarm when the set detection is triggered. press OK to stop alarm.
NOTE: If you have questions with any function. please feel free to contact [email protected] for one-on-one customer service guidance
Functions
-
Pan/Tilt
Rotate your camera by sliding on your smartphone. providing you with a good vision. -
Video flip
Flip your video stream up or down for maximum flexibility. -
Motion detection
The camera can detect movement. and then the camera will send you push notifications and app alerts. -
Crying detection
The camera can detect the crying of your baby and the camera will send you push notifications and app alerts. -
Temperature & humidity detection
The camera can detect the temperature and humidity of the environment. and the camera will send you push notifications and app alerts. -
Record
Support 24H continuous recording with high capacity SD storage or Cloud storage. -
Day & Night
Never miss a moment. even in complete darkness. with powerful night-vision technology.
FAQ
Q: The display cannot be previewed properly?
A: Check whether the display has connected to the camera. If not. pair the camera and the display firstly.
Q: Cannot find the pairing button?
A: The pairing button is the call button of the camera. Long press the button for 3 seconds. and follow the step instructions of the display. (To enter the pairing interface of the display, press the Menu button on the display screen. and select > Camera Management.)
Q: What if the display screen is stuck and it doesn't work while pressing any buttons?
A: Press the reset button of your display with the pin, and then long press the power button of your display to restart it.
Q: Why the camera or the display cannot identify the SD card?
A: Confirm whether the SD card is normally available and the format is FAT32.
Q: Why I can't get the notifications with my cell phone App when I connect the camera to the display?
A: Please confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system has been opened.
Q: How can I add devices or configure my network?
A: The camera can be connected to both the monitor and the application. Generally, it connects to the monitor by default. Please fallow the steps below to connect the camera to the application. 1. Make sure the Wi-Fi network is a 2.4GHz network, as the camera does not support 5GHz Wi-Fi. 2. Download the appropriate application on your phone. Register a new account to sign in or sign in indirectly. 3. Reboot the camera with the pin until the red status light flashes slowly (you must connect the camera to the opp within 2 minutes or you must reboot the camera again). 4. Follow the step-by-step instructions on your smartphone to add the screen and scan the QR code with the camera.
Q: The device prompts offline?
A: 1. Check whether the equipment is in the power on state, and observe whether the working light of the equipment is on normally. 2. Check whether the Wi-Fi network is in good condition and restart the router. 3. If the device is located far away from the router, which results in the inability to obtain a good Wi-Fi signal. it is recommended to move the router to a closer place or add a WiFi amplifier to improve the WiFi performance of the home. 4. Delete the camera from your BoifunCam account and add it again after resetting the device. Check whether the device firmware and application program are the latest version.
Q: Update router or Wi-Fi password?
A: Delete the camera from your BoifunC □ m account After resetting the device, use the new Wi-Fi and password to add it again.
Q: Can't play historical video?
A: 1. Check the status of the SD card in Settings' to ensure that the SD card has been successfully recognized. 2. Reinsert the SD card. 3. In the application. format the SD card. 4. Try another new SD card.
Q: The phone cannot receive the alarm push?
Q: The sound and cry detection function does not work.
If you encounter any other problems. please send your order and problem to [email protected]