boifun VB805 Video Baby Monitor Camera User Manual
- June 14, 2024
- BOIFUN
Table of Contents
VB805
Product Manual
VB805 Video Baby Monitor Camera
Sales Email : [email protected]
AFTER-SALE SUPPORT
Dear friends,
Thank you very much for supporting Boifun!
If you have any issues, please email your order number and the problem to
[email protected] . Receiving your message, we will
provide a fast solution in 24 hours.
Please do not worry. Actually, many problems can be easily solved by setting.
If you have any questions or ambiguities during using, please feel free to
contact us. We will try to find a good solution with our professional product
engineers.
Warm Regards.
Boifun Service Team
http://qr.hotlnk.cn/url/79829027072
DESCRIPTION
| 1. Light Sensor | 6. Infrared Lights |
|---|---|
| 2. Camera Lens | 7. Speaker |
| 3. Power LED Indicator | 8. DC Jack IN |
| 4. Microphone | 9. Temperature Sensor |
| 5. ON / OFF Switch | 10. PAIR Button |
| 1. Antenna | 8. Return Button | 15. Volume Level LED |
|---|---|---|
| 2. Brightness Buttons | 9. PTT Button | 16. Speaker |
| 3. Volume Buttons | 10. Signal LED Indicator | 17. Battery Compartment |
| 4. Power ON / OFF / Sleep Button | 11. Charging LED Indicator | 18. Kickstand |
| 5. Lullaby Control Button | 12. Navigation Buttons | 19. DC Jack IN |
| 6. Zoom Button | 13. Microphone | |
| 7. Menu / OK Button | 14. LCD Screen |
| 1. Signal Strength Indicator | 8. Lullaby Playback Active |
|---|---|
| 2. Channel Selected | 9. Current Time |
| 3. Temperature Of The Baby’s Room | 10. Battery Power |
| 4. Zoom Level | 11. PTT Function Active |
| 5. VOX Function Active | 12. Pan & Tilt Function Active |
| 6. Alarm Timer Active | 13. Backlight Brightness Bar |
| 7. Volume | 14. Volume Level Bar |
Specificatioms
General:
RF Frequency:| 2400 MHz – 2483 MHz
Spread Spectrum:| FHSS
Operating Temperature:| -10 to +45° C
Transmission Range:| Up to 1000 feet in open field
Monitor:
LCD Display:| 5′ LCD
Resolution:| 1280X720 pixel
Battery:| 3050mAh Li-ion 3.8V rechargeable
Time To Full Charge:| 5 Hours
Power Adapter| Input: 100-240VAC,50-60Hz; Output: 5V/1.2A ,Type C
Camera:
Sensor:| CMOS 1280X720 pixel
Vertical Turning Angle:| 90° up, 45° down
Horizontal Turning Angle:| 165° left, 165° right
Night Vison:| 8 IR LEDs
Power Adapter:| Input: 100-240VAC,50-60Hz; Output: 5V/1.2A,Type C
CONNECT THE CAMERA TO THE MONITOR
NOTE: Use only the power adapters included in the package. If the display
screen and the red power button are not on, you need to connect the monitor to
the power cord for charging.
Step 2: Connect the camera to the power cord;
Step 2: Turn on
the camera, and the btue LED lights up;
Step 3: Long
press the display switch for 3 seconds, the red power light is on;
NOTE: If you have problems with connection,please feel free
to contact [email protected] for one-on-one customer
service guidance.
Pairing
NOTE: The Baby Unit is pre-registered and connected to your Parent
Unit.If you need to pair Baby Unit and Parent Unit again, do the following:
Step 1: Select MENU > Camera > Add Camera > OK; 
Step 2: Please short
press PAIR button on Baby Unit. 
NOTE: If you have problems with
connection,please feel free to contact adminic buifun.net for one-on-one
customer service guidance
FAQ
Q: The monitor cannot be previewed properly?
A: Check whether the monitor has connected to the camera. If not, pair the camera and the monitor firstly.
Q: Display and camera cannot be paired?
A: Please refer to “CONNECT THE CAMERA TO THE MONITOR” on page 5 and “Paring” on page 6 of the Product Manual for pairing. NOTE: 1. Please connect the camera and display to the power cord for charging to avoid failure caused by power exhaustion; 2. Please confirm that you have turned on the switch of the camera, and the blue power light is on; the red power light on the display is on.
Q: Why does the monitor or camera sometimes make a slight noise?
A: Please do not place the camera and the monitor too close (less than 30 cm), too short transmission distance will cause the signal to be transmitted in a loop, resulting in noise.
Q: Why does the monitor screen not light up when the camera detects sound?
A: 1. Please confirm that you have turned on the VOX function; 2.Please select the sensitivity of VOX mode according to your needs: low/ medium/high.
If you encounter any other problems,please send your order number and problem to [email protected]. Receiving your message,we will provide a fast solution via email within 24 hours.