Sportneer B089KFXCLY ‎Bike Wall Mounts22 Instruction Manual

June 14, 2024
Sportneer

Sportneer B089KFXCLY ‎Bike Wall Mounts22 Instruction Manual
Sportneer B089KFXCLY ‎Bike Wall Mounts22

COMPONENT DIAGRAM

COMPONENT DIAGRAM

Hook combination

  • 2-3
  • 1-1 Hook (2PCS)
  • 1-2 Hook locking nut (2PCS)
  • 1-3 Balance adjustment group
  • 1-4 Allen bolt (4 pcs)

Extension arm set

  • 2-1 Extension arm
  • 2-2 Screw cap
  • 2-3 Screw and metal drywall anchor
  • (3 pcs plastic plug, 3 pcs metal plug

Tools Required

  • Drill
  • 8 mm drill bit
  • Phillips screwdriver
  • Hammer (for masonry or concrete walls)
  • Allen Key (Included

WARNING

  1. Do not mount hanger on the drywall(plasterboard), wooden walls or unsupported walls unless there is a wooden stud behind it. (If you lack the DIY skills to install hanger, seek professional help.)
  2. Avoid electrical circuits, water pipes, or plumbing hidden in walls.
  3. Weight limit for hanger is 25kg/55 lbs.
  4. Make sure the hanger is mounted correctly and sturdily before hanging your bike.
  5. Mount the hanger in a safe, appropriate place where your bike is unlikely to cause obstruction.
  6. Check all the parts of bicycle wall hanger. You must screw tight the loose screws and replace any defective part before operation to avoid damages.
  7. Do not use the bicycle wall hanger for bike repairing or maintenance.
  8. Do not allow kids to climb or play near the bicycle wall hanger to avoid potential dangers.
  9. Do not use the bicycle wall hanger in humid places or places with high salinity to avoid rusting and shortening its lifespan.

MOUNT HANGER

For masonry or concrete walls
Mark 3 driling holes with a pencil and drill these holes with an 8mm (0.31″) driller. Then insert the screw into the drywall anchor, nail them together into the marked position with a hammer and ensure they are stably fixed, and finally tighten them with the provided screw cap
MOUNT HANGER

For a wood pile or wooden walls with a certain thickness
Choose your desired mounting positions and add a solid plank between the wall and the bicycle wall hanger. Nail the plank into the wood pile or wooden wall with a hammer to ensure the bicycle wall hanger can be stably fixed onto. If the wooden wall or wood pile is less than 7cm thick, be sure to add a plank between it and the bicycle wall hanger
MOUNT HANGER

For Drywall(plasterboard) (The thickness is over 7cm)
Use a stud finder to locate wall studs behind wall, and mount a wooden board on wall studs .Place the bracket on wooden board, and then fasten bracket on board with screws. (It is recommended not to mount the bicycle wall hanger on a plaster wall, and not allowed to mount it on a hollow wall.)
MOUNT HANGER

ASSEMBLE HANGER

  1. Adjust length according to bike handlebar width

  2. Install the hook and balance kit to the hanger beam

  3. Test hanger’s stability before hanging bicycle.

HANG BICYCLE

  1. Adjust hanger beam length with Allen key according to bike handlebar width.
    HANG BICYCLE

  2. Adjust the distance between 2 hooks with allen key according to length of bike’s top tube.
    HANG BICYCLE

  3. Adjust the hooks’ angel
    HANG BICYCLE

  4. Place the top tube on the hooks to hang up the bike.
    HANG BICYCLE

  5. Tie the wheel strap.
    HANG BICYCLE

Sportneer logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals