V I V O STAND-V002O Dual Arm Monitor Desk Mount Instruction Manual

: June 14, 2024
: V I V O

Table of Contents

STAND-V002O Dual Arm Monitor Desk Mount
Product Information
Product Usage Instructions
Step 1: Clamp Installation
Step 2: Grommet Installation
Step 3: Arm Assembly
Step 4: VESA Plate Installation
Step 5: Monitor Installation
Step 6: Secure Monitor
Step 7: Cable Management

STAND-V002O Dual Arm Monitor Desk Mount

Product Information

The Mechanical Arm Dual Monitor Desk Mount is a versatile and
adjustable mounting solution for two monitors. It allows you to
free up desk space and create a comfortable and ergonomic viewing
experience. With a weight capacity of 4.4-19.8lbs (2-9kg) per arm,
it can accommodate most standard-sized monitors.

The package includes the following components:

(x2) Lower Arm
(x2) Upper Arm
(x1) Base
(x2) VESA Plate
(x1) Upper Clamp
(x1) Lower Clamp
(x1) Grommet Plate
(x1) Knob
(x2) M6x8mm Screw (S-A)
(x2) M6x10mm Screw (S-B)
(x2) M8x30mm Screw (S-C)
(x8) M4x12mm Screw (M-A)
(x8) M5x12mm Screw (M-B)
(x8) M5 Washer (M-C)
(x1) 4mm Allen Wrench (T-A)
(x1) 5mm Allen Wrench (T-B)

Please note that some of the included hardware may not be
used.

Product Usage Instructions

Step 1: Clamp Installation

Remove the plastic shroud from the Base (C).
Adjust the knob completely down on the Lower Clamp (F).
For desktops with a thickness of 0.4-1.90″ (10-50mm), install
the Upper Clamp (E) to the Base (C) using the M6x8mm Screws (S-A)
and the 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto
the Base (C).
Attach the Lower Clamp (F) to the top two holes on the Upper
Clamp (E) using the M6x10mm Screws (S-B) and the 4mm Allen Wrench
(T-A). Secure the clamp assembly to the desktop.
For desktops with a thickness of 1.8-3.1″ (45-80mm), follow the
same steps as above, but attach the Lower Clamp (F) to the bottom
two holes on the Upper Clamp (E).

Step 2: Grommet Installation

Mark two drilling locations 2″ (51mm) apart in the desired
location.
Drill grommet holes using a 3/8″ (10mm) drill bit, drilling
completely through the desktop.
Disassemble the Lower Clamp (F) using the Phillips end on the
5mm Allen Wrench (T-B).
Place the Grommet Plate (G) on Knobs (F1, H) and secure the
assembly to the desktop.

Step 3: Arm Assembly

Place the Lower Arms (A) onto the Base (C) and the Upper Arms
(B) onto the Lower Arms (A).
Tighten the set screws using the flathead end on the 4mm Allen
Wrench (T-A).

Step 4: VESA Plate Installation

Attach the VESA Plates (D) to the Upper Arms (B) using the
M8x30mm Screws (S-C) and the 5mm Allen Wrench (T-B).

Step 5: Monitor Installation

Install two Screws (M-A or M-B) and M5 Washers (M-C) to the top
VESA holes on the monitor using the Phillips end on the 5mm Allen
Wrench (T-B). Leave at least 3mm of clearance between the screw and
the monitor.
Slide the monitor onto the VESA Plate (D), making sure the
screws sit within the slots.

Step 6: Secure Monitor

Tighten the top two screws and install the remaining Screws
(M-A or M-B) and 5mm Washers (M-C) using the Phillips end on the
5mm Allen Wrench (T-B).

Step 7: Cable Management

Remove the bottom plastic covers from the Lower Arm (A) using
the Phillips end of the 5mm Allen Wrench (T-B).
Slide plastic covers off of the Upper Arms (B).
Run cables from the monitors through the bottom of the Upper
Arms (A) and Lower Arms (B).
Reattach the plastic covers.

Mechanical Arm Dual Monitor Desk Mount
Instruction Manual

SKU: STAND-V002O
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products /stand-v002o
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

help@vivo-us.com

www.vivo-us.com Chat live with an agent!

309-278-5303

WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER: · NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND. · USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS

A (x2) Lower Arm

B (x2) Upper Arm

C (x1) Base

D (x2) VESA Plate

E (x1) Upper Clamp

F (x1) Lower Clamp

G (x1) Grommet Plate

H (x1) Knob

S-A (x2) M6x8mm Screw

S-B (x2) M6x10mm Screw

S-C (x2) M8x30mm Screw

M-A (x8)

M-B (x8)

M4x12mm Screw M5x12mm Screw

M-C (x8) M5 Washer

T-A (x1) 4mm Allen Wrench

T-B (x1) 5mm Allen Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY.

4.4-19.8lbs

Failure to do so may result in serious injury.

(2-9kg)

PER ARM 2

ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation Remove plastic shroud from Base (C). Adjust the knob completely down on Lower Clamp (F).
F

C

For 0.4″-1.90″ (10-50mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the top two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure clamp assembly to the desktop.
C

T-B

S-A

E

S-B

T-A

F

OR For 1.8″-3.1″ (45-80mm) desktops install Upper Clamp (E) to Base (C) using M6x8mm Screws (S-A) and 5mm Allen Wrench (T-B). Reinstall the plastic shroud onto Base (C). Attach Lower Clamp (F) to the bottom two holes on Upper Clamp (E) using M6x10mm Screws (S-B) and 4mm Allen Wrench (T-A). Secure clamp assembly to the desktop.
C

T-B

S-A

E

S-B

T-A

F

3

STEP 1 (Option B)
Grommet Installation Mark two drilling locations 2″ (51mm) apart in desired location. Drill grommet holes using a ” (10mm) drill bit drilling completely through the desktop. Disassemble Lower Clamp (F) using the Phillips end on 5mm Allen Wrench (T-B). Place Grommet Plate (G) on Knobs (F1,H) and secure assembly to the desktop.
T-B
F F1
G
H F1
STEP 2
Place Lower Arms (A) onto Base (C) and Upper Arms (B) onto Lower Arms (A). Tighten set screws using the flathead end on 4mm Allen Wrench (T-A).
B

T-A

A

C 4

STEP 3
Attach VESA Plates (D) to Upper Arms (B) using M8x30mm Screws (S-C) and 5mm Allen Wrench (T-B). T-B
D S-C
B
STEP 4
Install two Screws (M-A or M-B) and M5 Washers (M-C) using the Phillips end on 5mm Allen Wrench (T-B) to the top VESA holes on the monitor leaving at least 3mm of clearance between the screw and monitor. Slide the monitor onto VESA Plate (D) making sure the screws sit within the slots.
D
T-B
5

STEP 5
Tighten the top two screws and install the remaining Screws (M-A or M-B) and 5mm Washers (M-C) using the Phillips end on 5mm Allen Wrench (T-B).
T-B
STEP 6
6

STEP 7
Remove bottom plastic covers from Lower Arm (A) using the Phillips end of 5mm Allen Wrench (T-B). Slide plasic covers off of Upper Arms (B). Run cables from monitors through bottom of Upper Arms (A) and Lower Arms (B), then reattach plastic covers.
B A
T-B
STEP 5
Adjust monitor tilt support using 5mm Allen Wrench (T-B) as shown. Adjust monitor position as desired.
T-B
7

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 09/15/2023 REV3

Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

www.vivo-us.com
Chat live with an agent!

AVG. RESOLUTION TIME (within office hrs): < 15 M

309-278-5303

AVG. RESOLUTION TIME (within office hrs): 5M 4S

help@vivo-us.com

AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com