DI-M204 Microwave Radar Sensor Instruction Manual
- June 15, 2024
- DIGITALas
Table of Contents
DI-M204 Microwave Radar Sensor
Product Information
Specifications:
- Technology: Microwave & microwave disposer
- Frequency: 24.125GHz
- Installation Height: 4M (MAX)
- Installation Angle: 0-90 degree (lengthways), -30 to +30 (lateral)
- Detection Mode: Motion
- Min detection speed: 5cm/s
- Power: 2W (VA)
- Detection range: 8m x 4m (Installation Height 2.2M)
- Maximum voltage: 42AC-60V DC
- Maximum Current: 1A
- Maximum switching power: 30W (DC) / 60VA (AC)
- Retention time: 0.5S
- Protection class: IP54
- Sheating material: ABS plastic
- Color: Black/silvery
Product Usage Instructions
Safety Instruction
Related parts should be operated under low voltage conditions. All installation processes and maintenance should be carried out by the supplier.
Name of Related Parts
- JST connection Red: 24V power cable
- Yellow: Relay COM/NO
Installation
- The indicator will shine for a few seconds when starting. When an object is detected by the sensor, the indicator lights up.
- Sensitivity potentiometer:
- Fluctuation up and down
- Rotation left and right
- NOTE: Initial setting is 45 degrees by factory. All the parameters above are only for reference, detection height is 2.2M. Detection range will be different because of the making material of door and ground, please adjust the sensitivity by the knob mentioned above. When it is adjusted to 60 degrees, the detection range is the widest, and the door will keep on closed and open all the time.
- Please do the installation in the proper position, installation height within 3.5m. Please arrange hole (mm) on the installation module. And hole (12m) for insetting guide line.
- Please connect the signal cable with the terminal of the automatic door.
- Brown and Yellow cable: AC/DC12V-24V
- Green and White cable: Signal output COM/NO
- Special Note:
- Take the outer cover off and fix the screws.
- Finish the cable connection and get power.
- Please set the detection range and disjunctor accordingly.
- Cover With The Lid
Adjustment (Get on power)
Detection range as below shown:
MIN | 1m | MAX | 2m |
---|---|---|---|
2 | 1 | 0 | 1 |
Sensitivity Adjustment:
Select different detection range by adjusting the sensitivity knob. Position should be fixed tightly to avoid vibrating. Do not place into moving object or other material. Fluorescent should be avoided. Do not touch directly, ESD Protection is necessary.
Failure Cause
Symptom | Cause | Method |
---|---|---|
Door & Indicator lose failure | Did not get on power | Check cable connection & |
power supply
Door keeps on closed and open| Sensor detected the movement of autodoor;
vibration of
movement| 1. Adjust angle
2. Check the position
3. Adjust sensitivity
Red indicator lose failure| 1. Switch of autodoor controller lose failure
2. Incorrect position
3. Incorrect output of sensor| Check the switch of autodoor controller &
setting of
output
Door keeps on moving when it rains| Sensor detected the actions of rain| Adopt
waterproof accessories
FAQ:
Q: What is the maximum installation height?
A: The maximum installation height is 4 meters.
Q: Can the installation angle be adjusted?
A: Yes, the installation angle can be adjusted from 0 to 90 degrees lengthways and -30 to +30 degrees laterally.
Q: What is the detection range?
A: The detection range is 8 meters by 4 meters at an installation height of 2.2 meters.
Q: What is the maximum switching power?
A: The maximum switching power is 30W (DC) or 60VA (AC).
Safety Instruction
Related part should be operated under low voltage condition. All installation process and maintainance should be carried out by the supplier
Name of related parts
Installation
- Please do the installation in the proper position,Installation height within 3.5m. Please arrange hole)mm٣٫٢φ(on the installation module. And hole (φ12m) for insetting guide line
- Please connect the signal cable with the terminal of automatic door.
- Brown and Yellow cable: AC/DC12V-24V
- Green and White cable: Signal output COM/NO
- Take the outer cover off , and fix the screws.
- Finish the cable connection and get on power.
- Please set the detection range and disjunctor accordingly
- Cover With The Lid
Adjustment
Adjustment( Get on power)
-
.Detection range as below shown
NOTE: Please stand out of the detection range around 5S to ensure the sensor has enough time to finish the self-adjustment. -
.Sensitivity Adjustment
- Detection Range
- MIN:0.5*0.4M
- MAX:4*2M
- Select different detection range by adjusting sensitivity knob
-
Adjustment of detection direction ( Adjust Direction of front and back/Left and Right flexibly) Adjusting angle of Plain aerial to get different detection distance and range 30 15×2range
NOTE:
- Initial setting is 45degree by factory.
- All the parameters above are only for reference, detection height is 2.2M.
- Detection range will be different because of the making material of door and ground , please adjust the sensitivity by the knob mentioned above.
- When it is adjusted to 60 degree, the detection range is the widest ,door will keep on closed and open all the time.
Special Note
Failure cause
Symptom | Cause | Method |
---|
Door&Indicator lose failure
|
Did not get on power
| Check cable connection & power supply
Door keep on closed and open
|
The sensor detected the movement
of autodoor; vibration of movement
| 1. adjust angle 2.check the position 3.adjust sensitivity
Door do not close
Red indicator lose failure
| 1. Switch of autodoor controller lose failure
2. incorrect position 3.Incorrect output of sensor
|
Check the switch of auto door controller &setting of ouput.
Door keeps on moving when it rains| Sensor detected the actions of rain|
Adopt waterproof accessories
Parameter
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>