NSL ES-LS2835-27K-42-24-30 LED Wall Washer Installation Guide

NSL ES-LS2835-27K-42-24-30 LED Wall Washer

FIXTURE INSTALLATION

Available in 2700K, 3000K, 4000K color temperatures: ES- LS2835-27K-42-24-30

Important: Read all instructions in order to ensure safety and proper installation.

NOTE: The product is sold in 33FT rolls, but the maximum single run is 16FT. Custom lengths available.

DIMENSION

OVERVIEW

1. End cap
2. Jumper connector
3. Power feed connector

MAINTENANCE

• Do not modify this fixture. Any modifications may render the product unsafe and void warranty.

Limited Warranty

The warranty applies to the product from the original date of purchase for three (3) years against manufacturing defects. The customer must provide proof of purchase. The manufacturer’s obligation under this warranty is limited to repairing or replacing the component. It is not related in any way to the cost of the connection, the installation of the replacement parts or cost of transport.

INSTALLATION GUIDE

WARNING: Disconnect power before installation or maintenance.

Mounting Clips Installation

1. Measure the required wall washer length and cut it at the marked cutting point. (Fig.1)
2. Insert glue in the power feed connector, then attach the power feed connector to the wall washer, with the pins under the printed circuit board. Push the connector until fully seated. Wipe the excess glue with a dry towel. (Fig. 2, Fig. 3, Fig. 4) DO NOT ALLOW GLUE TO SEEP INTO THE CONNECTION POINTS.
3. Insert glue in the end cap, then attach the end cap to the wall washer. Push the end cap until fully seated. Wipe the excess glue with a dry towel. (Fig. 5, Fig. 6)
4. Let the assembly to dry for 3-4 hours.
5. Install the mounting clips on the surface using the screws provided. (Fig.7)
6. Insert the LED Wall washer in the mounting clips. (Fig.8)
7. Connecting the power feed connector leads to the low voltage (24V DC) of the driver (Fig.9).
8. Connect the incoming 120V AC wires to the input of the driver.
9. Turn on the power.

Installation with “L” type extrusion to reduce glare

1. Measure the required length and cut the wall washer at the cutting length. (Fig.1)
2. Measure the aluminum extrusion and cut at desired length.
3. Insert glue in the power feed connector, then attach the power feed connector to the wall washer, with the pins under the printed circuit board. Push the connector until fully seated. Wipe the excess glue with a dry towel. Let it dry for 15 min. (Fig. 2, Fig. 3, Fig. 4)
4. Slide the wall washer through the extrusion.
5. Insert glue in the end cap, then attach the end cap to the wall washer. Push the end cap until fully seated. Wipe the excess glue with a dry towel. (Fig. 5, Fig. 6)
6. Let the assembly to dry for 3-4 hours.
7. Install the assembled wall washer+extrusion in the desired position using the wall plugs provided.
8. For wall mounting, select appropriate size of wall mount brackets for desired effect.
9. Connecting the power feed connector leads to the low voltage (24V DC) of the driver.
10. Connect the incoming 120V AC wires to the input of the driver.
11. Turn on the power.

Ceiling Mounting

Floor Mounting

Wall Mounting

• Several wall mounting brackets available to enhance the wall washing effects in various applications.

Indoor/Outdoor Dimmable Drivers

TRE24L40DC

• 6.77” X 2.67” X 1.26” (171 X 68 X 32mm)

TRE24L96DC

• 6.77” X 2.67” X 1.26” (171 X 68 X 32mm)

Non-Dimmable Drivers

LEDDR-24-120W

• Indoor/Outdoor driver 120W hardwire
• Input: 100 – 240V AC; Output: 24V DC
• 10” x 3 3/8” x 3 3/16” (254 x 85.7 x 80.9mm)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>