secrui M520 F55 Doorbell Wireless Doorbell with 2 Receivers User Manual

June 14, 2024
secrui

Wireless Doorbell
User Manual Model:M520+F55

Content

Content will vary according to your kit
The push button supplied with this kit is pre-programmed to operate with the doorbell.
If it is not, see “Connect a Push Button” on page 5

Safety

Before proceeding with the installation, please note the following safety warnings:

  • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
  • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

What You Should Know Before Installation

  1. Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
  2. Set a desired music (different or same one) for transmitters before installation. For music setting, see Operating Instructions Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
  3. Please do not install transmitter on metal doors since it s hard for the signal to transmit.
  4. Please take out the battery insulating strip before using. ((As picture 2)
  5. Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.

Product Structure Diagram

AC Powered Receiver

  1. Music Control
  2. Volume Control
  3. Plug
  4. LED light
  5. Speaker

Waterproof Transmitter

Set Up and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell will light up and ring. If it does not, see “Connect a Push Button” on page 5.

  1. Adjust the Volume
    Press the 1s. (when the power is cut off, and power is restored again, the volume will be automatically adjusted to maximum)

  2. Change the Tune
    Press the Loop tones in sequence and play the current tones.
    Long press 5s Change tones loop direction.
    Press and hold the to power on:The doorbell receiver will turn on after beeps ten times, indicating that the doorbell receiver wil restore the track to the first song, and all the buttons are not deleted.

  3. Connect a Push Button
    You can connect up to 20 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.
    (1)VARIABLE – Tone Pairing
    1. Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beeps once, which means receiver get into pairing mode.
    2. Press push button, the receiver will beeps twice with LED indicator flashes 1s.
    3. Press push button again, the receiver will beeps once with LED indicator flashes 1s, which means the pairing is successful.
    4. Short press or leave it 20s without any operation, the doorbell will exit the pairing mode. Adding the additional push buttons or receivers please according to the above steps.
    (2)FIXED – Tone Pairing (only play your saved tone)
    1. Select a tone that you like
    2. Pressing and holding the & button for about 5s until the receiver beeps once, which means receiver get into pairing mode.
    3. Press push button once, the receiver will beeps twice with LED indicator flashes 1s.
    4. Press push button once again, the receiver will beeps once with LED indicator flashes 1s, which means the pairing is successful.
    5. Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.
    1. Select music 2. &
    3. Press 5-7s 3. Beepstwice, Press Flashes1s
    4. Beepsonce, Press Flashes 1s
    5. Short press, done. Adding the additional buttons/receivers please according to the above steps.
    Note : Pair and set only one transmitter at a time to avoid interference and ensure successful operation.

  4. Reset (Clearing out Settings)
    To return all settings to their default settings Hold down and plug it into an outlet.
    After playing the beep 10 times, all settings will return to factory defaults.
    Hold down and Plug in

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.

  1. For Receive
    Plug-in receiver: Just plug receiver into standard outlet in room.

  2. For Push button:
    IMPORTANT: Before installation, please test if the operating range you choose is working and set music if needed.
    Before you drill any hole in the wall, please make sure there are not cables or pipes.
    To install you will require a drill and cross-head- ed screwdriver.

  3. Open the Transmitter with screw driver and separate the front cover from the back cover.
    Penetrate the two standby holes at the back cover with two screws. Then fix the screws on the wall at suitable height.

  4. Or you can stick the Transmitter with the double-sided adhesive tape.

If you are not mounting the push button to the wall, place it where you want it.

Number Song Name
1 Dingdong-1
2 Dingdong-2
3 Dingdong-3
4 Scale 135i
5 Scale i531
6 Dingdong-4
7 Dingdong-5
8 Dingdong-6
9 Dingdong-7
10 Dingdong-8
11 Bell-1
12 Bell-2
13 Bell-3
14 Bell-4
15 Dingdong-9
16 Dingdong-10
17 take me out to the ball game
18 A Comme amour
19 Susanna
20 Symphony No.40 in minor
21 Serenade for strings in G major
22 Love story
23 doraemon
24 Ten little Indians
25 Nutcracker two
26 Fast Ding Dong Ding Dong
27 Violin Concerto – spring
28 Four little swans
29 Serenade
30 Minuet
31 To Alice
32 Auld Lang Syne
33 Carman Overture
34 Bach Minuet
35 Turkey March
36 Music 01
37 Nokia classic ringtones
38 Radetzky march
39 Scale 1351 1531
40 Ringing tone
41 Romeo and Juliet
42 Kung Fu episode
43 Violin Concerto No.1
44 Drinking song – Camellia girl
45 kiss the rain
46 Irish thrush
47 Lake Baikal
48 Cannon
49 Romance in the rain
50 Titanic
51 Scale 5351
52 Romance of love
53 Tetris
54 Yesenia
55 mermaid
56 Merry Christmas
57 Scarborough fair
58 Music box of love

Battery Replacement of Push Button

Open the battery cover and install the CR2032 battery.

Specification

| Doorbell| Push Button
---|---|---
Operating Temperature| -4°F to 140°F| -4°F to 140°F
Radio Frequency| 433 MHz| 433 MHz
Range (open field)| 1,000 ft| 1,000 ft
Sound Level (typical)| 0-120 dB| _
Battery Type| Plug in| CR2032
Battery Life (5 activations/day)| Up to 5 years| Up to 3 years
Rain Proof| N/A| IP55

Troubleshooting

If Then
The doorbell does not work 1.The doorbell might be out of range; try the

doorbell in a different location.
2.Reconnect the doorbell. See “Connect a Push Button” on page’s.
3.Check all the batteries and replace if needed.
4.Checkif the LED on the transmitters is working \when activated.
5.Check if the doorbell is muted. Check that the transmitter is linked with the chime.
Range is reduced| 1.Metal structures including uPVC door frames can reduce the range.
Don’t mount the the doorbell or doorbell push on or near metal structures.
2.Move the doorbell closer to the doorbell push button.
Weak batteries will reduce range.
In cold conditions (below 5°C), batteries may need to be replaced more often.

1 Year Limited Warranty

This product is warranted to the original purchaser only for a period of 1 year from the date of purchase for products damaged due to defect in workmanship and materials. Proof of purchase s required to obtain warranty service.
Warranty is for replacement only. No service parts are available for these products. No other warranties are expressed or implied.Batteries are not covered under this warranty.
For warranty service, please contact SECRUI Customer Service by email: support@secrui.com
IMPORTANT: PLEASE KEEP THESE INSTRUC-TIONS FOR FUTURE REFERENCE WHEN REPLACING BATTERIES
Made In China

https://www.youtube.com/channel/UCEgFORimGgvo_-LO9qXvk6Q
Brand: SECRUI
Manufacturer:Shenzhen Kerui Smart Technology Co., Lid
‘Address: Room 1501, T2, inltong Buiding, No. 1100, Xingye Road
Xin’an Strect, Ba0’an District Shenzhen, Guangdong, China
Email support@secrul.com
Youtube: Secrul Tech
WEEE. Reg-N. DE 32633950
Made in China
prolinx Gmbt
Brehmst, 56 40239 Duesseldorf
Telefon: +4921131 054698
Name: Acces AR ltd
Nires:fice 243 Nelson Roxd, London, SEL0 918
Contactpeson: ene Znen
Tel:+44 7513 984663
Emai info@accessar.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals