secrui M508 Wireless Doorbell User Manual
- June 14, 2024
- secrui
Table of Contents
Wireless Doorbell
User Manual
Model:M508+F55
Content
Content will vary according to your kit
The push button supplied with this kit is pre-programmed to operate with the
doorbell fit is not, see Connect a Push Button” on page 5
Safety
Before proceeding with the installation, please note the following safety warnings.
- Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
- Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt
What You Should Know Before Installation
- Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
- Set a desired music (different or same one) for transmitters before installation. For music setting, see Operating Instructions.Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory
- please do not install transmitter on metal doors since it is hard for the signal to transmit
- Please take out the battery insulating strip before using. (As picture (1)
- Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.
Product Structure Diagram
AC Powered Receiver
- Music Control
- Volume Control
- Plug
- LED light
- Speaker
Set Up and Operation
Press the push button to test whether it is paired with the doorbell, The doorbell will light up and ring. If it does not, see “Connect a Push Button” on page S.
-
Adjust the Volume
Press the is. (When the power is cut off, and power is restored again, the volume will be automatically adjusted to maximum) -
Change the Tune
Press the is: Loop tones in sequence and play the current tones.
Long press5s -change tones loop direction. -
Connect a Push Button
You can connect up to 20 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.
VARIABLE – Tone Pairing
- Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beeps once, which means receiver get into pairing mode.
- Press push button, the receiver will beeps twice with LED indicator flashes 1s.
- Press push button again, the receiver will beeps once with LED indicator flashes 1s, which means the pairing is successful.
- Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.
Adding the additional push buttons or receivers please according to the above steps.
FIXED – Tone Pairing (only play your saved tone)
- Select a tone that you like
- Pressing and holding the & button for about 5s until the receiver beeps once, which means receiver get into pairing mode.
- Press push button once, the receiver will beeps twice with LED indicator flashes 1s.
- Press push button once again, the receiver will beeps once with LED indicator flashes 1s, which means the pairing is successful.
- Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.
- Select music & Press 5-75.
Adding the additional buttons/receivers please according to the above steps.
Note ; Pair and set only one transmitter at a time to avoid interference
and ensure successful operation.
Reset (Clearing out Settings)
To return all settings to their default settings
Hold down and plug it into an outlet.
After playing the beep 10 times, all settings will return to factory defaults.
Hold down and Plug in
Installation
Choose a location that is not near a heat source or on something that moves
(like a door). For non-mounting locations, choose a place where the doorbell
will be easy to see and hear.
L.For Receiver:
Plug-in receiver Just plug receiver into standard outlet in room.
For Push button:
IMPORTANT
Before installation, please test if the operating range you choose is working
and set music if needed
Before you drill any hole in the wall, please make sure there are not cables
or pipes
To install you will require a drill and cross-head ed screwdriver.
( Open the Transmitter with screw driver and separate the front cover from the
back cover.
Penetrate the two standby holes at the back cover with two screws. Then fix
the screws on the wall at suitable height. 
Or you can stick the Transmitter with the double-sided adhesive tape.
If you are not mounting the push button to the wall, place it where you want it
Battery Replacement of Push Button
Open the battery cover and install the CR2032 battery.
Specifications
| Doorbell| Push Button
---|---|---
Operating| -4°F to
140°F| -4°F to
140°F
Temperature
Radio Frequency| 433 MHz| 433 MHz
Range (open field)| 1000 ft| 1000 ft
Sound Level (typical)| 0-120 dB| _
Battery Type| Plug in| CR2032
Battery We
(5 activations/day)| Up to 5
years| Up to 3
years
Rain Proof| N/A| IP55
Troubleshooting
| If | Then |
|---|
The doorbell
does not work| 1. The doorbell might be out of range; try the doorbell in a
different location.
2. Reconnect the doorbell. See Connect a Push Button” on page 5.
3. Check all the batteries and replace if needed
4. Check if the LED on the transmitter is working when activated.
5. Check if the doorbell is muted Check that the transmitter is linked with
the chime.
Range is
reduced| 1. Metal structures including uPvC door frames can reduce the range
Don’t mount the the doorbell or doorbell push on or near metal structures.
2. Move the doorbell closer to the doorbell push button. Weak batteries will
reduce range.
In cold conditions (below 5C), batteries may need to be replaced more often.
Year Limited Warranty
This product is warranted to the original purchaser only for a period of 1
year from the date of purchase for products damaged due to defect in
workmanship and materials. Proof of purchase is required to obtain warranty
service.
Warranty is for replacement only. No service parts are available for these
products. No other warranties are expressed or implied.Batteries are not
covered under this warranty.
For warranty service, please contact SECRU
Email support@secrui.com
IMPORTANT: PLEASE KEEP THESE INSTRUC
TIONS FOR FUTURE REFERENCE WHEN
REPLACING BATTERIES
Prolinx GmbH
Brehmstr.56,40239 Duesseldorf
Germany
Telefon: +4921131054698
Email: eu@eulinx.eu
Name: Access AR Ltd
Address: Office 3,4a Nelson Road, London, SE10 9JB
Contact Person: Irene Zheng
Tel:+44 7513 984663
Email: info@accessar.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>