secrui M5373 Waterproof Wireless Doorbell User Manual

October 30, 2023
secrui

secrui logo M5373 Waterproof Wireless Doorbell

secrui M5373 Waterproof Wireless Doorbell User Manual

Safety

A Before proceeding with the installation, please note the following safety warnings:
Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment when drilling holes, etc.
Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

What You Should Know Before Installation

  • Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
  • Set a desired music (different or same one) for transmitters before installation. Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
  • Please do not install transmitter on metal doors since it is hard for the signal to transmit.
  • Please take out the battery insulating strip before using if have. (As picture (1))
  • Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.

secrui M5373 Waterproof Wireless Doorbell - fig

Product Structure Diagram

secrui M5373 Waterproof Wireless Doorbell - fig 2

  1. LED Light
  2. Music Control
  3. Volume Control
  4. Plug
  5. Speaker

secrui M5373 Waterproof Wireless Doorbell - fig 3

  1. Led Indicator
  2. Push Button

Set up and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell will light up and ring. If it does not, see “Connect a Push Button” on page 5.

  1. Adjust the Volume
    Press the to adjust the volume. (when the power is cut off, and power is restored again, the volume will be automatically adjusted to maximum)
    At the maximum and minimum volume, the door bell will sound “Didi” twice
    There are total 5 levels including the mute mode.

  2. Change the Tune
    Press the to loop tones.secrui M5373 Waterproof Wireless Doorbell - fig
5

  3. Connect a Push Button
    You can connect up to 20 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.
    VARIABLE- Tone Pairing
    Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beep once, which means receiver get into pairing mode.

Long Press SSD

  • Press push button, the receiver will beep twice with LED indicator flashes 1s.

  • Press push button again, the receiver will beeps once with LED indicator flashes 1s, which means the pairing is successful.

Notice:

  • Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.

  • Adding the additional push buttons or receivers please according to the above steps.
    Fixed- Tone Pairing (Only play your saved tone)

  • Select a tone that you like

  • Pressing and holding & button together for about 5s until the receiver beeps once, which means receiver get into pairing mode.

  • Press push button once, the receiver will beep twice with LED indicator flashes 1s.

  • Press push button once again, the receiver will beeps once with LED indicator flashes 1s,which means the pairing is successful.

Notice:

  • Short press (4)] or leave it 20s without any operation, the doorbell will exit the pairing mode.
  • Pair and set only one transmitter at a time to avoid interference and ensure successful operation.

Delete a Push Button

Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beeps once, which means receiver get into pairing mode.
Long Press 5s

  • Pressing and holding the [@)] AGAIN for 5s, the receiver will beeps 4 times, LED flashes 4 times, which means all push buttons deleted.

Reset (Clearing out Settings)

To return all settings to their default settings. Hold down and plug it into an outlet. After playing the beep 10 times slowly and beep 6 times fast , all settings will return to factory defaults.

secrui M5373 Waterproof Wireless Doorbell - fig 13

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.

  1. For Receiver:
    Plug-in receiver: Just plug receiver into standard outlet in room.

  2. For Push button:
    IMPORTANT:
    Before installation, please test if the operating range you choose is working and set music if needed.

  • Before you drill any hole in the wall, please make sure there are not cables or pipes.
  • To install you will require a drill and cross-head-ed screwdriver.

A. Open the Transmitter with screw driver and separate the front cover from the back cover. Penetrate the two standby holes at the back cover with two screws.
Then fix the screws on the wall at suitable height.

secrui M5373 Waterproof Wireless Doorbell - fig 14

B. Or you can stick the Transmitter with the double-sided adhesive tape.

C. If you are not mounting the push button to the wall, place it where you want it.

Battery Replacement of Push Button

Open the battery cover and install the CR2032 battery

secrui M5373 Waterproof Wireless Doorbell - fig 16

Specifications

| Doorbell| Push Button
---|---|---
Push Button
Temperature| -4°F to
140°F| -4°F to
140°F
Radio Frequency| 433.92 MHz| 433.92 MHz
Range (open field)| 1,000 ft| 1,000 ft
Sound Level (typical)| 0-120 dB|
Battery Type| Plug in| CR2032
Battery Life (5 activations/day)| Up to 5 years| Up to 3 years
Rain Proof| N/A| Ip55

Trouble shootings

If Then
The doorbell does not work 1. The doorbell might be out of range; try the

doorbell in a different location. 2.Reconnect the doorbell. See “Connect a The doorbell Push Button “on page 5. does not work 3.Check all the batteries and replace if needed. 4.Check if the LED on the transmitters is working when activated. 5.Check if the doorbell is muted. Check that the transmitter is linked with the chime.
Range is reduced| 1. Metal structures including uPVC door frames can reduce the range. Don’t mount the doorbell or doorbell Range is push button on or near metal structures. reduced 2. Move the doorbell closer to the doorbell push button. Weak batteries will reduce range. In cold conditions (below 5°C), batteries may need to be replaced more often.

1 Year Limited Warranty

This product is warranted to the original purchaser only for a period of 1 year from the date of purchase for products damaged due to defect in workmanship and materials. Proof of purchase is required to obtain warranty service. Warranty is for replacement  only. No service parts are available for these products. No other warranties are expressed or implied. Batteries are not covered under this warranty.
For warranty service, please contact SECRUI
Customer Service by email: contact@secrui.com
IMPORTANT: PLEASE KEEP THESE INSTRUC-TIONS FOR FUTURE REFERENCE WHEN REPLACING BATTERIES Made In China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals