VEVOR SKF-C66FT Ice Maker Instruction Manual

ICE MAKER
SKF-C66FT E-mail: support@vevor.com
E-mail: support@vevor.co.uk

IMPORTANT SAFETYINSTRUCTIONS

When using electrical appl ances, basic safety precautions should be followed to reduce the risk offire, electric shcckand njuryto personsorproperty. Read all irstructicns before operating the machine for the first time.
CAUTION: ICE CAN’T BE STORED IN THE ICE BIN CURING NIGHT TIME,IT’S NOT FRIDGE,ICE WILL BE MELTED TO WATER AND GET OUT OF THE MACHINE.

1. If connect with water supply, CAUTION: must connect the potable water surply;
2. The mach ne is ntended ta be used in Fousehold and similar appl cations such es:
   -staff kitchen areas in shops,offices and other werking environments;
   -farm houses
   -by clients in hotels,motels and other residential type environments;
   -Catering industry and simi ar ron-retail ndustry.
3. The mach ne shculd be used in household and without obstacles surrounded, good ventilation place.There is must be 50cm at least between the four sides of the machine with the wall.
4. When tsing electr cal app! ances,basic safety precautions sheuld be followed to reduce the risk of fire, electric shock and njury ta persons or property. Read ail nstructions before using any appliance.
5. Don’t operate this or any other appl ance with a darraged cord.
6. Connect te properly polarized outlets only. No other appliance should be plugged into the same outet.Be sure that the clug ‘s fully nserted into the socket.
7. Don’t place the mech ne and power cord rear flammable raterial. Do not cover the cord. Do not submerge it in water.
8. We do not recommend the use of an extension cord,as t may overheat and become a risk of fire.
9. Unplug the ice maker before cleaning or making any repairs or servicing.
10. Exercise caution and supervision when appliance is used rear children.
11. Don’t use your ice maker outdeors Avoid direct sun! ght and make sure that there is at least 50cm of space between the back and sides of your unit and the wall.
12. Don’t use any liquid other than water in the unit to make the ice.
13. Do not clean your ice maker with flammable detergents. The fumes can create a fire hazard or explesion.
14. Do not tip the machine over.
15. If the ice maker is brought indoors from cutdoors during the wintertime,give it a few Fours to warm up to room temperature before plugging te power source.
16. This unit sheuld be properly grounded for your safety. The power cord is equipped with a three-prong plug which mated with standard three prong wall outlets to minimize the pcssibility of electric shock.
17. Plug your appliance into a dedicated, properly installed and grounded wall outlet. Do not,under any circumstance power and /or grounding shculd be directed toward a certified electrician.
18. The foaming materials inside is combustible which must be kept away from fire.
19. It’s forbidden to pull the cable to unplug the plug,pull the plug is a must.

IMPORTANCE: To avoid hazard due to instability,unit must be placed on an even and flat surface.
WARNING: The méchine must be grounded.

1. Only connect to drinking water sources that meet local drinking water standards.
2. In addition to the method recommended by the manufacturer, no mechanical equipment or other methods should be used to accelerate the defrosting process, which will damage the system.
3. The refrigeration system contains high-pressure refrigerant, and the refrigeration system must not be damaged. Special care must be taken during instal ation and handling, installation and mainter ance must be performed by a professional, and scrap must be d sposed of by designated recycling departments.
4. The ice machine has thermal nsulation materials, which are flammable rraterials, and must be kept away from the fire source.

Quick installation diagram
Note: The picture is for reference only. Please be subject to the actual prodicts. NOTE: Installation must be operated by a professional.

UNPACKING YOUR ICE MAKER

Warning: Please keep foam and other packaging materials from children and disabled people, as this may cause danger to them.
NOTE: Please remove all packages when using,or else the machine may not work properly.
a) Remove the peckaging and check whether the machine is intact.
b) Open the accessory peckage and check whether the accessories are included.

Accessories list (Please be subject to the actual products)

NO| Description| Picture| Usage| QTY
0.| Manual| | Operation manual| 1PC
2| Filter| | Filter water| 1PC
3| Drainage pipe| | Drain| 1PC
4| Ice spoon| | Take ice cubes| 1PC
S| nylon cable ties| | Fix pipe if needed| 2PCS
6| Hoop| | fasten the outlet and the drainage pipe together if needed| 1PC
7| Seal ring| | Do put one in the faucet of the intake pipe, the other one is spare.| 2PCS
a| Spare blue clip| | Spare blue clip if needed.| 2PCS
9| Spare plug| | Spare plug which plug the lank if needed.| 1PC

1. The placement of the machine
   a) Find a location for your ice maker where it’s protected from direct sun| ght and other sources of heat (i.e. stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at east 5 nches of space between the back and sides of your ice maker and the wall.
   b) The ambient temperature around the machine should not be lower than 3, not higher than 40°C, ensure there is at least 50cm of space between the back and sides of your unit and the wall.
   c) The machine shculd be placed on a stabie place.
   d) Please do not put anything on top of the machine.
   e) After you unpack the machine, we recommend you to eaving it for 24 Fours before turning it on.
   f) Clean the interior with lukewarm water and a soft cloth or clean the unit using the Self- Clean furctien.
   g) The appliance must be pcsitioned where the plug is accessible.

2. Water connection of the machine
   Warning:
   a. The ice machine can only be connected to a drinking water source, and the water source must comply with Iccal drinking water standards.
   b. The water supply to the ice maker must be connected to a filter to mprove the drinking standard of the water. Please do not directly connect to tap water.
   c. The water supply pressure should be within 0.1-0.4MPa, if the pressure is greater than 0.4MPa, a pressure reducing valve needs to be connected.
   d. The machine is drained by its own weight, so the drain pipe shculd have sufficient height.

3-1) Water intake 3-2) Drainage
Warning: Because the ice in the inner tank will melt, drain pipe must be connected before using, and insert the drain pipe into a container or into the sewer.
Note: Connect one end of the drain pipe to the machine, and the other end to a container or sewer. The other port of the drain pipe must be lower than the drain port of the machine. 4)Electrical connection
WARNING: This appliance must be grounded.

1. The fuse on the PCB is 8A (220V machine), if 110-120V machine, the fuse is 15A, if change, must be operated by a technician.
2. The fusing current of the electrical box must be >10A, If it is to be replaced, must be operated by a technician.
3. voltage fluctuation can’t be exceed +10% than rated voltage, or a Voltage stabilizer is needed.’
4. The blue light installed inside the machine must be replaced by a professional.

MACHINE OPERATIONS

Operation Panel Ice making operation
ON/OFF BUTTON:
Press this button under standby mode( display “—”)to make the machine to work,press the button for 2 seconds during working time,the machine will be power off.
Cleaning/Reservation:
Long press this button for 3s under standby mode to make the enter cleaning mode for 5min and with cleaning indicator is on.And it will enterstandby mode after cleaning.
Press cleaning button during cleaning mode to make the machine end the cleaning in advance.
Press this button under standby mode with the reservation indicator Flicker. and the “4” /”.” button to set the auto-turning-on time (in hoursfrom 0-23h). The machine will automatically turns on after The countdown is finished.and the “+”/“-” button to set the auto-turning-off time (in hoursfrom 0-23h). The machine will automatically turns off after the countdown is finished.
If we succeed in reservation,the reservation light will be always on.
Press reservation button to cancel the reservation and the reservation indicator will be off.
HOT:
You can long press the “Hot” button 3 second during the ice making to make the ice cubes drop from the ice mold ahead of time.
Press “HOT” to turn off the blue light,press again to turn it on.
“+””and“-” button:
Through “+”/”-” to increase or decrease ice making time or set the auto- turning-on/ off time,the “thickness adjust” indicator will be always on.
Ice making time can be adjusted from -8 to 8min.(e.g. if display 15,press “-” to adjust to -2,will display 13,that’s mean,ice making time was adjusted to 13min )

Display ice making countdown time {in minute),display increase or decrease ice making time (in minute),display reserve auto-turning-on/off time (in hours)

CLEANING & MAINTENANCE

Please thoroughly clean your ice maker before ‘nitial use.
EXTERIOR: the cutside of the ice maker should be cleaned regularly with a mild detergent and warm water. Always use a soft cloth to avoid scratching or darraging the housing.
SPOON: clean with mild detergent and warm water in week.
Storage tank: clean with mild detergent and warm water in week.
PUMP: clean with mild detergent and warm water in week. Turn off end unplug the machine,take the pump out,clean it with a brush then install it back.
INTERIOR: please use the fol owing Self-Clean function:

1. Add water and vinegar or emon juice mix (1:1 ratio)
2. Plug in unit,press and hold the CLEAN button for approximately 6-7 seconds,then release.The unit will automatically enter Self-cean program. This process takes about 5-6 minutes,When the Self-Clean program is finished, unit will automatically power off.
3. The fan blade will be rotating. This process rinses the nside parts several times.
4. After the Self-Clean program is completed,unplug the power cord and drain out the water by unplugging the drain cap on the side.Replace drain cap.
5. Add fresh water to the water reservoir,up to the water level mark.
6. Plug the unit and repeat the Self-Clean process by repeating steps 3 to 5. This will rinse out the vinegar/lemon residue.
7. After draining the water,replace and tighten drain cap.
8. Dry the interior and exterior with a clean,soft cloth.

NOTE: It is strongly recommended to clean the unit before nitial use or after the unit has not been in use for a long period of time.

Circuit Diagram

NOTE As the production of ice cubes increases, the plastic panel inside the machine (shown above) m ght be pressed down by the ice cubes. When the plastic panel is pressed down, the machine will stop producing ice cubes automatically and the “stoppage’indicator will light on. Pease clean out the ice cubes regularly for continuation of ice raking.

Explosion diagram

1. visible door
2. Door frame
3. Top cover
4. Board light
5. Back panel
6. Front cover
7. Display board cover
8. Display board| 9. Display board box
10. Inner tank
11. Water tank
12. Ice mold
1.3. Float
14. Pump
15. Compressor
16. DC fan| 17.C ondenser
18. Main board cover
19. Main board
20. Main board box
21. Rubber feet
22. bottle seat
23. bottle seatc over
---|---|---

Common malfunction analysis

El| Ice full indicator is on,and proximity switch didn’t react| Evaporator connector didn’t assemble wet| Re-install the connector
---|---|---|---
Proximity switch is not sensitive| Replace the switch
The connector didn’t return to original position| Take away the ice to make the connector return to original position
E2| Nrrnal to make ice| Stop every 4 cycles,and the process of ice drop continued for 5 min| Proximity switch is not sensitive,replace it
No water in the tank| The water tank is not plugged| Put the plug back
Use tap water as water source| Check the water supply
Use tap water as water source| Water pressure is too high,water float can’t work.Adjust the water pressure or replace by a new one.
Water in the tank| No water or low flow| Pump is badly clogged up,replace or clean it
The spray pipe is clogged up,clean it
E2| Water flow and water get cool| Thin ice on the evaporator| Increase the making time through “+“
very solid ice on the evaporator| Reduce the making time through “..’
Some water sprayed to ice storage tank| Adjust the spray pipe
The water leak from the back of water tank| The Lank need to be adjusted.
Water flow down but water Is not cool| The main board didn’t supply electricity to compressor| Replace by a new main board
Compressor didn’t work| Check the starter,replace by a new one if reeded
Compressor is very hot| Replace
Compressor work but the connected copper pipe didn’t get cool| The compressor leak
E3| The tan is not work| The condenser prob is not sensitive| Unplug the prob or replace by a new one
The fan is jammed| Adjust the fan
Fan is broken| Replace by a new fan
14| Ice full| The connector didn’t return to original position| Take away the ice to make the connector return to original position

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>