RELAX4LIFE BC10006 Baby Bed Folding Crib with Changing Table Hanging Toy Instruction Manual
- June 14, 2024
- RELAX4LIFE
Table of Contents
BC10006 Baby Bed Folding Crib with Changing Table Hanging Toy
Instruction Manual
Before You Start
Please read all instructions carefully and keep it for future reference.
General Warnings:
Attention: To prevent possible injury by entanglement, remove this toy
when the child starts trying to get up on its hands and knees in a crawling
position.
Dangert Keep all small parts and packaging materials for this product away
from babies and children, otherwise they may pose a choking hazard.
The product must be installed and used under the supervision of an adult.
Read through each step carefully and follow the proper order.
Remove all Packaging, separate and count all parts and hardware before
installation.
Please ensure that all parts are correctly installed, incorrect installation
can lead to a danger.
We recommend that, where possible, all items are assembled near the area in
which they will be placed in use, to avoid moving the product unnecessarily
once assembled.
Ensure a secure surface during installation, and place the product always on a
flat, steady and stable surface.
IMPORTANT!!!
RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY.
WARNING
♦ Warning: Be aware of the risk of open fire and other sources of strong
heat, such as electric bar fires,gas fires, etc. in the near vicinity of the
cot.
♦ Warning: Do not use the cot if any part is broken, torn or missing and
use only spare parts approved by the manufacturer.
♦ Warning: Do not leave anything in the cot or place the cot close to
another product,which could provide a foothold or present a danger of
suffocation or strangulation, e.g.strings, blind/curtain cords,etc,
♦ Warning: Do not use more than one mattress in the cot.
STATEMENT
This cot is ready for use,only when the locking mechanisms are engaged and you
need to check carefully whether they are fully engaged before using the
folding cot. If the height of the cot base is adjustable, the lowest position
is the safest and that the base should always be used in that position as soon
as the baby is old enough to sit up.
If you leave the child unattended in the cot, always make sure that the
movable side is closed, if movable sides are provided,
It is essential to remove rails before the cot is used in its lowest position
if detachable support rails are provided to support the cot base above its
lowest position,
Thickness of the mattress shall be such that the internal height(surface of
the mattress to the upper edge of the cot frame) is at least 500mm(19.7″) in
the lowest position of the cot base and at least 200mm (7.9%) in the highest
position of the cot base.
The length and width shall be such that the gap between the mattress and the
sides and ends does not exceed 30mm.
All assembly fittings should always be tightened properly and that fittings
should be checked regularly and retightened as necessary.
To prevent fall injuries, when a child is able to climb out of the crib, the
crib should no longer be used.
TO CLEAN
Do net dry clean or use bleach.
Do not machine wash, tumble or spin dry, unless the care labelling on the
product permits these methods.
Non removable fabric covers and trims may be cleaned using a damp sponge with
soap or mild detergent, allow it to dry completely before folding or storing
it away.
In some climates the covers and trims may be affected by mould and mildew.
To help prevent this occurring. do not fold or store the product if it is
darnp or wet, always store the product in a well ventilated area.
TO UNFOLD
- Unzip the carry bag and remove the cot.(Fig.1)
- Undo the hook&loop straps that hold the mattress around the frame.(Fig.2)
- Remove the mattress and set it aside.
- Now separate the legs from the cot.(Fig.3)
- Starting from the short rails, and pull them up quickly with both hands until they lock into place. (Fig. 4)
- Now do the same with the longer rails.(Fig.5)
- Holding one end of the cot clear of the ground, gently press down on the centre of the cot base until it lays down flat .(Fig.6)
- Put the sheet onto the mattress(if applied)with the padded side facing up and pass the loop straps through the gap in the sheet.
- Place the mattress into the cot with its padded side facing up.(Fig.7)
- Secure the mattress into the cot by passing the loop straps through the slot in the cot base and securing it onto the hook attachment, sewn onto the underside of the cot base itself.
Note ‘All the top rail should be locked into places. The cot base must be in a raised position to allow the rails to lock easily. Ensure all four top rails are securely engaged by press down on all rails.
TO FOLD
- Release the loop straps that are securing the mattress and remove the mattress from the cot.
- Locate the handle strap in the center of the cot base and pull it up to upright position (at least $0 cm (19.7”))(Fig.8)
- Release each top rail by lifting the rail slightly and squeezing the bottom of each center joint. The buttons are covered by the top rail fabric, located at the bottom of each rail .(Fig.9,Fig. 10)
- After ensuring that every rail is fully released, pull up on the cot base handle strapwhile gathering the legs and the frame together, until the cot is completely folded.
- Take the mattress and wrap it around the frame. Ensuring that straps are on the outside(Fig.11).
- Thread the loop straps through the plastic loops,pull them tight and secure them. (Fig.12)
- Put the folding cot in the carry bag.(Fig.13)
Note NOTE THAT IF THE TOP RAIL DOES NOT FOLD, DO NOT FOLD IT FORCEFULLY.
PLEASE RE-SQUEEZE THE BUTTONS TO RELEASE THEM COMPLETELY.
BASSINET (IF APPLIED)
- Before installing the bassinet, make sure the 4 top rails are maintained on their position (straight and flat).
- Take out mattress from cot and keep it within reach.
- Install the safe net on the cot.
- Make sure all hooks are tightly attached on the edge of top rails.(Fig. 14)
- Install 2 pairs of support tubes, insert the tubes into the tube holder of the safety net, then connect the tubes together. (Fig. 15)
- Place mattress onto mesh and frame. (Fig.16)
CHANGER or CANOPY (IF APPLIED)
Unfold the changer and connect 2 rods. Then clamp the two plastic hooks onto the top rails and make sure to secure them as shown in the picture. (Fig. 17) Attached the two clips of toy bar on long handrails, one for each side. Make sure the two clips are securely attached to the rails. (Fig. 18).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>