4512750 NAMRON ZIGBEE LED Instruction Manual

NAMRON 4512750  ZIGBEE LED Instruction Manual

Assembly Instruction

LED/CFL:3W-200W
:3W-200W
:3W-100W
Dimming Method| Phase-cut
**** Working Environment| Temperature：-10℃ – 35℃
Humidity：10% R.H. – 90% R.H.
Model Size| 71mm×71mm×52mm(L×W×H)

WARNINGS AND CAUTIONS

1. Risk of fire and electrical shock, the dimmer should be installed in accordance with appropriate electrical codes and regulations.
2. The dimmer should be protected by a 16A maximum miniature circuit breaker.
3. Turn power off at circuit breaker or fuse and test that power is off before installing.
4. After install the dimmer, it is recommended to set the minimum brightness level to make bulbs turn on immediately.
5. If you are unsure about any part of these instructions, consult a licensed electrician.
6. To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle, a motor-operated appliance or a transformer-supplied appliance.
7. Use with compatible dimmable LED, CFL bulbs, Incandescent or halogen bulbs only.
8. When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED, CFL or incandescent. Using the same model of each bulb will enhance dimmer performance.
9. This product complies to EN60669-2-1.

Splicing Design

Functional Specifications

Status Indicator

Indicator lights blue and flash: Enter to ZigBee mode connection.

Input and Output Terminals

N: Input terminal (Connect the neutral and live wire “N”)

L: Input terminal (Connect the live wire “L”)

Output terminal (Connect the bulbs)

P: Signal input terminal (Connect the self-reset switch-output terminal)
Short press: Within 0.5s
Long press: Over 0.5s
Continuous short press: Each interval of short press should within 1s

Push-button Rotary Switch

Turn on: Short press one time when in OFF.
Turn off: Short press one time when in ON.

Dimming:
a. Turn clockwise to increase the brightness.
b. Turn counterclockwise to decrease the brightness.
c. Long press to adjust the brightness when in ON status. Release and long press again to change the direction of the dimming brightness. Continuous short press two times when in ON/OFF can quickly turn to the full brightest. Setting the ideal min brightness when in on status, continuous short press six times and the lamp flash three times. Setting the ideal max brightness when in on status, continuous short press eight times and the lamp flash three times.
Network mode: Continuous short press seven times when in ON status. then the APP can connect the dimmer when the bulb flash once and the status indicator turn blue and flash.

1. If failed to connect, APP will exit the network mode after three minutes.
2. During the network connection, the lamp may flicker if the light is in the brightest. After the network is successfully configured or the network is been withdrawn, the lamp will return to normal).
   Continuous short press nine times when in on status and the lamp flash five time to clear the setting brightness(min or max).
   Restore factory Settings: Continuous short press ten times when in ON and the lamp flash once.

Tools Needed To Install e Dimmer

Installation

WARNING: To avoid fire and electrical shock, TURN PFF POWER at circuit breaker or fuse and test that power is off before wiring.

Choose the connection of 5.3.1 or 5.3.2 to install the dimmer per your requirement. *The wire core cross-sectional area of the terminals is 0.75 mm² – 1.5mm²,stripping length is 9mm.

Typical wiring application
Live Wire
Way

Multi-way

NOTE:

(a) The dimmer should be connected to the electricity side of the load to ensure normal work.
(b) The dimmer support to connect with multiple self-reset switches (20pcs at most) to control the UP/DOWN and ON/OFF at the same time.
(c) Two or more dimmers should not be connected in parallel or series to control the same load from two different locations.

Multipl self-switches control one dimmer wiring diagram

Oneself-reset switch control multiple dimmers wiring diagram

Multiples elf-reset switches control multiple dimmer swirling diagram

Neutral and Live Wire
Way

Multi-way

NOTE:

(a) The dimmer should be connected to the electricity side of the load to ensure normal work.
(b) The dimmer support to connect with multiple self-reset switches (20pcs at most) to control the UP/DOWN and ON/OFF at the same time.
(c) Two or more dimmers should not be connected in parallel or series to control the same load from two different locations.

Multipl self-reset switches control one dimmer wiring diagram

One self-reset switch control multiple dimmers wiring diagram

Multiple self-reset switches control multi-way dimmers wiring diagram

Installing dimmer

Divide the dimmer into two parts. (Operation Component, Panel and Drive Component)
Carefully position all wires inside the wall-box, leaving enough space to insert the dimmer housing.
Put the Drive Component inside the wall-box and align at the screw holes(①②)
Tighten the screws(①②) to let the Drive Component stick to the Junction Box.

Install the Operation Component to the Fixing Panel and put them together to the Drive Component.

User Instructions
Function Instructions

Table 1 1-way application function

App Operation
---|---|---|---|---
**** Network Mode| Continuous short press thepush-button rotary dimmer seven times| √| ×| ×
ON/OFF| Short press the push-button rotaryswitch one time| √| √| √
Dimming| Turn the push-button rotary switch| √| √| √
Quickly turn to the full brightest| Continuous short press thepush-button rotary switch two times| √| √| √
Set the min brightness| Continuous short press the push-button rotary dimmer six times| √| ×| ×
Set the max brightness| Continuous short press the push-button rotary dimmer eighttimes| √| ×| ×
Clear the setting(min or max ) brightness| Continuous short press thepush- button rotary dimmer nine times| √| ×| ×
Restore factory Settings| Continuous short press the push-button rotary switch ten times| √| ×| ×
Schedule on/off| NO| ×| ×| √
Share device| NO| ×| ×| √
Group control| NO| ×| ×| √

Priority
The operation of self-reset switch could stop the operation of APP, when at the operation of self-reset switch, APP operation could not work

Troubleshooting

Importer:
Namron AS
Nedre kalbakkvei 88 B
1081 Olso
Norway
Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>