LASER ALC-MIROR-170 Mirrored Alarm Clock User Manual
- June 15, 2024
- Laser
Table of Contents
ALC-MIROR-170 Mirrored Alarm Clock
User Manual
ALC-MIROR-170 Mirrored Alarm Clock
Mirrored Alarm Clock
ALC-MIROR-170
WHAT’S IN THE BOX
- Mirror Clock
- Stand
- USB-A to USB-C power cable
- User manual
You may also need:
- USB power adaptor
CONTROLS AND PORTS
OPERATIONS
INSTALL THE STAND
Insert the stand into the two recesses at the bottom of the clock.
To remove, pull it out gently.
TURNING ON THE CLOCK
Connect the clock to a USB power adaptor using the USB-A to USB-C cable.
SET TIME
- In Time mode, hold down the M button until the screen starts flashing. The setup sequence is:
- Pres the or button to adjust 12hr/24hr clock, hour, and minute digits.
- Press the M button to switch between 12hr/24hr, hour and minute, and save the time.
NOTE: If power is disconnected, all settings will be reset to their default.
SET ALARM
-
In time mode, press the M button to switch to alarm mode.
-
Hold down the M button until the time starts flashing.
The setup sequence is hour → minute → snooze time: -
Pres the or button to adjust the hour and minute digits, and snooze time. The default snooze time is 5 minutes with max at 60 minutes.
-
Press the M button to switch between hour, minute, and snooze time.
-
When the alarm is activated, the AL symbol will be displayed on the clock.
-
In Time mode, press the – button to turn on/ off the alarm.
SNOOZE FUNCTION
- The buzzer will sound for 2 minutes. Press the Snooze button to start the snooze; the AL symbol will start flashing.
- Press any button other than the Snooze button to turn off the alarm or snooze mode.
ADJUST CLOCK BRIGHTNESS
- Manual Method – In time mode, press the or button to cycle between Bright, Medium, and Low brightness modes. Bright mode is the default setting.
- Using ambient light sensor – The clock display will adjust according to the brightness of the environment when the light sensor setting is turned on. The display will be brighter in brighter environments and dark in dim-lit environments. The setting is set to Off by default. Hold down the or button to turn on/off automatic light-sensing function.
SET NIGHT MODE
The clock brightness will be set to Low mode from 6 PM to 6 AM each night by
default. The default night mode state is Off.
NOTE: For the night mode function to work, the ambient light sensor
function must be turned off.
In Time mode, double press the M button to enter the night mode.
Press the or button to change the state On/Off.
To change the night mode time period, press and hold the M button when night
mode is on. The setup sequence is: 
CHARGE YOUR DEVICES
Connect your devices’ charging cable to the mirror clock and your phone.
TROUBLESHOOTING
CLOCK IS NOT TURNING ON
Make sure the clock is securely connected to a USB power adaptor and it’s
working. You can check by using another USB-A to USB-C cable, USB power
adaptor and power outlet.
ALARM DOES NOT GO OFF
Make sure you have set the alarm time correctly. Check if the alarm is turned
ON and the alarm symbol showing.
USB CHARGING IS NOT WORKING
Make sure the USB cable is securely connected to both the clock and the device
that needs recharging. Try the other USB port. If it still does not work, use
a different USB cable.
SPECIFICATIONS
| Power input | 5V 2A |
|---|---|
| USB-A power output (shared) | 5V 2A |
| Dimensions (WxDxH) | 158x13x78 mm |
| Weight (net) | 108g |
Thank you for your purchase!
Laser Corporation is 100% Australian owned & operated. To get the most out of
your product please read the user manual carefully and keep for future use.
For specific information relating to your product such as Spare Parts, FAQs,
Warranty claims, and more, please scan the following QR code:
https://www.laserco.com.au/support
Visit our website www.laserco.com.au
Check us out at www.youtube.com/lasercoau
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>