JBC B·IRON 210 Battery-Powered Soldering Station Instruction Manual

JBC B·IRON 210 Battery-Powered Soldering Station Instruction Manual

This manual corresponds to the following references:
BIS-5A
according to purchased station model, suitable for: 120V – N. America / Taiwan 230V – India / Europe / United Kingdom

Packing List

⚠ Please read this manual and its safety guidelines thoroughly before using the product.

Features & Connections

Quick Start

8. Tool Selection

Select the tool from the device list. If the tool is not displayed on screen, make sure that the cap is off and the tool has some battery. Try scanning again by tapping Scan (6) on the display.

To add a second tool to the station once the first one is connected, go to the main menu (7) and tap Add device. Select your second tool from the device list.

Status Lightband

The status lightband indicates as follows the tool status:

Tool Cap and Tool Cap Holder

Thanks to the cap for B210 and B115 handles, tools can be safely transported even with a cartridge inserted.
When the cap is placed onto the tool, the cartridge stops heating inmediately, data transfer is cut off and the tool is disconnected from the station. It turns off completely after 10 minutes of inactivity. This allows a greater saving of the tool’s battery.
The stand has a holder for two tool caps on the back. This component can be detached by loosening and removing the screw between the two holders (1).
While the tool is being used, the cap can be stored on the tool cap holder.

Operation

The JBC Most Efficient Soldering System

This revolutionary technology can recover tip temperature extremely quickly. This allows the user to work at a lower temperature.

Work Screen

The Work screen shows a graph of the tip temperature and power supplied to the tip updated in real time. It allows to modify the tool working temperature, check the battery status and turn on and off the tool in use.

Graph and Automatic Data Display
The graph display of the temperature and supplied power starts automatically as soon as the tool is lifted from the charging base.
The graph display can be paused while working by tapping the screen on the graph area. While the automatic display is on hold, the temperature/power values can be checked at a certain point of the graph by tapping on the desired position on the display screen.

Note: Pausing the automatic display by tapping on the screen does not stop the tool from heating up, and the tip will remain at the selected working temperature.
The graph can be moved to the left and right by swiping the touch screen sideways with one finger.

Working Temperature Modification
The working temperature can be modified using the slider below the graph (± 5 ºC / ± 10 ºF).

Stopping Data Display
When the tool is placed on the tool holder or when it enters Hibernation Mode, the data display stops.
The display starts again automatically when the tool is lifted from the tool holder and the graph is automatically displayed again at the point where the previous display stopped, leaving a small gap on the graph between the last registered value and the new starting point.

Working with Two Tools
When working with two tools, to switch between the two graphs, tap on the tool selector (upper-right corner of the display) and select the desired tool from the drop-down menu.
It is also possible to alternate both graphs by simply lifting one tool or the other from the tool holder. The display will automatically show the graph and information of the tool in use.
Note: All menu items are explained in detail starting at section “Menu”.

Cartridge Exchanger

The cartridge exchanger saves time and allows to change cartridges safely without switching the tool off.

Cartridge Holder for C210 Cartridges

The cartridge holder (4x slots) is used to store cartridges. It allows to have different cartridges quickly at hand and it works with C210 Cartridges.

Cartridge Adapters for C115 Cartridges

Since C115 cartridges have a smaller diameter than C210 cartridges, adapters must be used to store them in the cartridge holder. These adapters must simply be inserted from above into the slots of the cartridge holder.

Tip Cleaner

Select the option that best suits your needs and improve the tip thermal transfer.

It also includes a temperature-resistant wiper for removing excess solder by gently tapping or wiping the cartridge tip on it.
If the tip is very dirty, JBC recommends cleaning it first with the wiper to remove excess solder and then with the brass wool.

Wiper

Replacing Brass Wool

Replacing Grips

Replacing Sealing Plugs

The sealing plug prevents undesirable flux vapours or particles from entering the handle.

Note: Depending on your handle model, two sealing plug references are available.

⚠ Before replacing the sealing plug, disconnect the tool from the station and make sure the device is not hot.

OB4000 for B210 Handles

For B210 handles the usage of OB4000 sealing plug is highly recommended for intensive applications when soldering is exposed to FOD environments or for applications where the soldering iron works close to a vertical position.

Tool Holder Disassembly and Replacement

Adjustable tool holders can be disassembled by loosening the screws (1) at the bottom of the charging stand and pulling downward from the side band (2).
⚠ Before sliding down the side band, hold the tool holder with your hand to prevent it from falling off.
Then, to install a new tool holder onto the charging base, place the tool holder at the top of the side rail and slide back the side band over it until it is secured in place. Finally tighten the screws at the base.
Find more information on Expansion Kits at www.jbctools.com.

Menu

Menu – No Tools Connected
Before any tool has been connected to the station or after the last tool has been disconnected, the menu offers these options.

Menu – Tool Connected
Once at least a tool has been linked, the menu expands and shows some more options.

Work
Takes the user to the work screen (see section “Work Screen”).

Settings
The B·IRON app offers an intuitive user interface, which provides quick access to several station parameters.

Counters

The Counters section allows the user to consult data and counts on charges, Work Mode periods, Sleep Mode periods, errors… The data can be consulted either by time periods or by number of times a certain event has occurred.

Update
Allows to update the firmware of the soldering station. To know more about the updating process, see section “Updating the Firmware”.

Documents
User manuals related to the station or to the tools can be consulted in this section or on JBC’s website: www.jbctools.com

Light/Dark Theme
Allows the user to switch between dark and light display modes.

Add Device
Connect a second tool to the station.

Disconnect
Disconnect the tool in use. If only one tool is connected, after disconnecting it, the app will return to the device list display.

Installing and Updating the B·IRON App

To install or update the app, some kind of internet connection is required (WiFi, cable, mobile data…).

1. Go to the App Store or Play Store (depending on your operating system).
2. Search for JBC B.IRON on the search bar.
3. Tap on the app and then on Obtain / Install / Update.

Alternatively, scan these QR codes to access the B·IRON app page directly:

apps.apple.com/es/app/jbc-b-iron/id1633983290

For Android devices the app installer can also be downloaded from: https://www.jbctools.com/jbcsoftware.html

Updating the Firmware

– Download the JBC update file to your PC from: https://www.jbctools.com/software.html.
– Connect the tablet/device via USB connection to the PC.
– Check if there is a folder named “JBC” in the internal storage of the Android device used as B·IRON display. If it doesn’t exist, create it.
– Copy the downloaded file to the JBC folder.
– Access the B·IRON app and, in the Menu, select Update.
– Tap on Select your firmware file and pick the downloaded file from the drop- down menu.
– Tap on Update (1).

Accessories

B·IRON soldering stations can be accessorized with some additional components specifically designed for them:

Display Holders
JBC offers display holders in two different sizes. Choose the size that best suits your needs and the device you use as display.

Maintenance

Before carrying out maintenance, always extract the cartridge from the tool and disconnect the charging stand from the mains. Allow the equipment to cool down.
– Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts.
– Periodically check that the metal parts of the tool and tool holder are clean so that the charging works properly.
– Maintain the tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
– Do not use liquids such as alcohol, thinner or benzene to clean the tablet.
– Repairs should only be performed by a JBC authorized technical service.

Safety

⚠ It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
– Do not use the units for any purpose other than soldering or rework. Incorrect use may cause a fire.
– The power cord must be plugged into approved bases. When unplugging it, hold the plug, not the wire.
– Do not attempt to dismantle or open the housing of the tool as it may cause damage.
– Do not work on electrically live parts.
– The tool should be placed in the stand when not in use in order to charge the batteries.
– The soldering tip or nozzle, the metal part of the tool and the stand may still be hot even when the station is turned off.
– Do not leave the tool unattended when it is on.
– Avoid flux coming into contact with skin or eyes to prevent irritation.
– Be careful with the fumes produced when soldering.
– Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm.
– Utmost care must be taken with liquid tin waste, which can cause burns.
– This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning the use of the appliance and understand the hazards involved. Children must not play with the appliance.
– Maintenance must not be carried out by children unless supervised.
– Do not expose the tablet to high temperatures, humidity or dust. Avoid direct sunlight.
– Do not drop the portable display or the tool, as it may cause damage or malfunction.
– Do not disconnect your device when it is in file transfer mode. – Do not use the portable display in places where wireless communications are restricted.

Safety – Battery

⚠ It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.
– Caution: This product contains lithium-ion batteries. Mishandling or improper use may result in fire, explosion, or personal injury.
– Always use the provided charger. Do not use damaged chargers or batteries.
– Never attempt to disassemble or modify the batteries or the product. Doing so may lead to electric shock, fire, or damage to the product.
– In the event of damage, leakage, or overheating of the batteries, discontinue use immediately and contact customer support or JBC technical service facility.
– Dispose of devices with batteries inside, responsibly according to regulations. They must be disposed of in accordance with local regulations so that they can be recycled.
– Do not throw devices with batteries into household waste and do not dispose of them in fire or water.

Specifications

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase.

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility.

www.jbctools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>