PORTOR LIGHTING PT-ABL-R-PTP-O LED Bollard Fixture Instruction Manual

: June 13, 2024
: PORTOR LIGHTING

Table of Contents

PACKAGE CONTENTS
INSTALLATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PT-ABL-R SERIES
**PT-ABL-R-DTP-C / PT-ABL-R-DTP-L / PT-ABL-R-PTP-O

**

PACKAGE CONTENTS

PORTOR LIGHTING PT-ABL-R-PTP-O LED Bollard Fixture - PACKAGE
CONTENTS

READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY
WARNING : RISK OF FIRE, ELECTRIC SHOCK, INJURY OR PROPERTY DAMAGE.

RISK OF ELECTRIC SHOCK–DISCONNECT POWER TO EQUIPMENT BEFORE INSTALLING OR SERVICING. THIS
EQUIPMENT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE CODES & ORDINANCES.
INSTALLATION AND SERVICE OF THIS EQUIPMENT MUST BE PERFORMED BY QUALIFIED SERVICE PERSONNEL.
READ THESE INSTRUCTIONS BEFORE INSTALLING, SERVICING OR MAINTAINING THIS EQUIPMENT.
THE INSTALLER MUST ENSURE THAT THE FOUNDATION IS STABLE AND CAN SUPPORT THE LUMINAIRE´S WEIGHT.
THE INSTALLER MUST USE PROPER MEANS TO SECURE THE LUMINAIRE TO THE GROUND.

CAUTION:

EDGES MAY CUT–WEAR GLOVES WHILE HANDLING OR SERVICING THIS EQUIPMENT.
INSPECT EQUIPMENT FOR DAMAGE FROM SHIPPING AND HANDLING.
RECOMMENDED CLEANING SUBSTANCES: WIPE OFF DUST WITH A DRY, SOFT CLOTH. REMOVE GREASY SPOTS ETC.
WITH A SOFT CLOTH DAMPENED IN LUKEWARM WATER (<122° F/ 50° C) WITH A MILD DETERGENT.
THIS FIXTURE REQUIRES A 120-277VAC POWER SOURCE.
OPERATING TEMPERATURE -40° C TO 50° C (-40° F TO 122° F).
SUITABLE FOR WET LOCATIONS.

CAUTION:

THIS DEVICE COMPLIES WITH FCC PART 15 SUBPART B. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INFERENCE RECEIVED, INCLUDING THAT MAY CAUSE UNDESIRED OPERATION.
RETAIN THESE INSTRUCTIONS FOR FUTURE MAINTENANCE REFERENCE.

WARNING RISK OF INJURY

Wear gloves and safety glasses at all times when removing, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source when fixture is on.

WARNING RISK OF FIRE

Keep combustible and other materials that can burn, away from lamp/lens.
Do not operate in close proximity to persons, combustible materials, or substances affected by heat or drying.

INSTALLATION

ALWAYS TURN OFF THE POWER SUPPLY FROM MAIN CIRCUIT BREAKER FIRST!

Get the anchor bolt carrier assembled as Fig. 1 and use it to determine placement of anchor bolts in concrete.
Install 3 anchor bolts into concrete as per attached Fig. 2, having at least 1-1/2~2” protruding from concrete with threads free and clear of debris and dirt (Electrical conduit are reserved in the concrete center).
Remove the 2# 3/4″plug screws, and select desired wattage & CCT, select desired EM & PC on/oﬀ, through the dial swithches on the driver box bottom plate. Fig. 3
Intall the head to the shaft and tighten the 3 screws.
loosen the 3 screws on the side of shaft bottom with the hex wrench and separate the ﬁxture body from the mounting base. Fig. 5
Place bollard mounting base over anchor bolts, and tighten M 10 ﬂat washer, M10 spring washer & M10*8 nuts Fig. 6 Fig 7 or to secure the mounting base to the foundation.
Connect the wires, then tighten the terminal block with a ﬂat-head screwdriver, and check to make sure all wires are in good connection Fig. 8
Put the ﬁxture body back on and tighten the 3 screws Fig. 9. Installation complete.