POWER-LITE ID7W Integral Driver Downlight Installation Guide
- June 15, 2024
- POWER-LITE
Table of Contents
POWER-LITE ID7W Integral Driver Downlight
Product Information
The LED ID7W and ID8W are high-quality downlights that provide certainty at the speed of light. These downlights are designed for indoor use and offer exceptional safety features. The fittings have an insulating ceiling type IC-4 rating, allowing them to be installed in areas with temperatures up to 90°C. They are suitable for use in bathrooms and covered/sheltered areas such as porches.
The downlights come in different sizes, with ceiling cutout dimensions ranging from 70-75mm for the 2.5-inch downlight to 190mm for the 8-inch downlight. The installation spacing requirements, as shown in Figure 1, ensure proper thermal insulation and building material clearance.
Before installation, it is important to check the IP label on the luminaire to determine the appropriate location for installation. The IP rating indicates the level of protection against water and dust. The downlights have IP20/IP40 ratings for indoor use only, IP44/IP54 ratings for use in bathrooms and covered/sheltered areas, and IP65 rating for outdoor areas.
Additionally, the downlights are available with different driver options. Non- dim drivers cannot be used with any dimmer, while Triac dim drivers are compatible with recommended TRIAC dimmers, offering a dimming range of 8-100%.
Product Usage Instructions
Follow these instructions to install and use the LED ID7W and ID8W downlights:
- Read all safety instructions provided in the user manual before installation.
- Ensure that a licensed electrician performs the installation.
- Choose the appropriate location for installation by checking the IP label on the luminaire.
- Turn off the power supply before starting the installation process.
- Verify that you have all the necessary tools and accessories to complete the installation correctly.
- If using a downlight with an internal driver, select the desired colour temperature (WW: 3000K, NW: 4000K, CW: 5700K) before installation.
- Cut a hole in the ceiling according to the specified cutout size for the chosen downlight.
- Using a screwdriver, open the driver terminal cover located on the back of the downlight.
- Feed the main AC wire L and N into the terminal block of the driver, ensuring proper connections.
- Securely fix the driver terminal cover back in place.
- Hold back the spring clip and push the downlight into the hole in the ceiling.
- Ensure that the downlight is fixed tightly in the ceiling.
- Turn on the power supply to activate the downlight.
Warning: To prevent the risk of overheating or fire, it is essential to switch off the power before installation and switch it on only after completing the installation and examining the circuit. Only professional electricians should perform the installation and maintenance of these downlights.
Important Safety Instructions
Basic safety precautions should always be followed when installing, including the following:
- Read all instructions.
- Licensed electrician for installation only.
- IP54 for indoor use only.
- Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning, changing the globe or adjustment to the fitting.
- Do not install any luminaire near the heat source.
- Do not exceed the nominal supply voltage or amperage ratings.
- To avoid damage to the fitting, please ensure that power leads and screws are secure before connecting the power.
Installation Instructions
The fitting has an insulating ceiling type IC-4 rating. Building material and
thermal insulation that can safely be exposed continuously to temperatures up
to 90℃ may abut and cover the luminaire.
If the building material cannot meet this condition, the minimum clearance of
25mm is required. See Figure 1：
Tab 1: Ceiling cutout reference table.
| Downlight dia (inch) | 2.5 | 3 | 4 | 6 | 8 |
|---|---|---|---|---|---|
| Ceiling Cutout (mm) | 70-75 | 90 | 120 | 160 | 190 |
NOTE: Before installation, please check the IP label on the luminaire to choose the right place to install.
| IP20/IP40 | Indoor use only, do not use in wet or damp place. |
|---|---|
| IP44/IP54 | Suitable for indoor areas including bathrooms and covered/sheltered |
areas such as porches.
IP65| Suitable for outdoor areas, not suitable for water immersion.
NOTE: Before installation, please check the information of driver as below.
| Non-dim | Can not be used with any dimmer. |
|---|---|
| Triac dim | Compliable with recommended TRIAC dimmers, dimming range 8-100%. |
Installation Procedure
WARNING
- Switch off before installation.
- Switch on only after complete installation and examination of the circuit.
- Professional electrician for installation and maintenance only.
- Risk of overheating of fire if the clearance distances are compromised.
Turn Off power supply before starting any installation. Read instructions & check you have all the tools & accessories to complete the installation correctly.
Downlight with internal driver
Please select the colour temperature before installation:
- WW: 3000K
- NW: 4000K
- CW: 5700K
- Cut a hole according to the cutout size of led downlight.
- Use screw-driver to open the driver terminal cover on the back of downlight, feed the main AC wire L. N. in terminal block respectively, then fix the cover back.
- Hold back the spring clip then push the downlight into the hole
- Make sure the downlight fixed tightly in ceiling, turn on the power (Fig 1).
RISK OF FIRE – Required clearance from structural members and building
elements
SCB=25mm HCB=25mm
Warning:
Input wire diameter ≥0.75mm²；
Product modification and improper installation void the warranty!
1800 909 306
nedlandsgroup.com.au
sales@nedlandsgroup.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>