Midea B8 MBC2080BB Bagged Vacuum Cleaner Instruction Manual

INSTRUCTION MANUAL
VACUUM CLEANER
B8 MBC2080BS

B8 MBC2080BB Bagged Vacuum Cleaner

PLEASE READ THE MANUAL CAREFULLY BEFORE USING AND KEEP IT PROPERLY FOR FUTURE USE
Warning notices: Before using this product, please read this manual carefully and keep it for future reference. The design and specifications are subject to change without prior notice for product improvement. Consult with your dealer or manufacturer for details.

Safety Introduction

1. For the first operation, it is advisable to read the manual carefully before hand and keep it properly for future use.
2. Before the first operation, make sure the dust cup or the dust bag is properly installed.
3. Make sure the power supply is 220-240V- 50-60Hz
4. Do not vacuum water and inflammable material.
5. Do not vacuum burning material and ashes.
6. Do not use the machine without a motor protection filter filled.
7. Please change the dust bag immediately when it was damaged.
8. Do not store or use the machine close to high temperature places.
9. Dot not let children use the machine in case of danger.
10. If abnormal noise, smell, smoke or any other failure or breakage is found during the operation, you should turn off the switch and unplug it. Then contact with your service center for repair. Do not repair by yourself.
11. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
13. . Children should be supervised to ensure that they do not play with the appliance.

Warning : The plug must be removed from the power socket before any maintenance or replacement. If the power cord is damaged, replace them only by the factory or maintenance center or similarly qualified persons.

GETTING TO KNOW YOUR CLEANER’

Product operation

Assembling your cleaner
Take out all components from the packaging.

1. Connect the hose to the cleaner main body, ensuring it locks into position. [1] To release the hose: rotate the connector counterclockwise and pull it. [2]
2. Connect the hose handle to the end of the fixed tube upper end and store the accessories on the tube. [3B]
3. Connect the tube lower end to carpet and floor nozzle. [3A]

USING YOUR CLEANER

1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the red marker. [5]

2. Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster and raise or lower the tube to the most comfortable cleaning position. [4]

3. Select Carpet or Floor Nozzle for ideal cleaning mode for the floor type. Hard Floor – Brushes are lowered to protect the floor.
   Carpet – Brushes are raised for the deepest clean.

4. Switch the cleaner on by pressing the on/off Pedal on the cleaner main body.  [6]

5. Adjust the power level by pressing the variable power control button or by pushing the variable power control slider. [7]

6. Adjust the suction regulator* to the desired level. [8]

7. Switch off at the end of use by pressing the on/off Pedal. Unplug and extract power cord again to wind the power cord back into the cleaner.

8. Parking and Storage – The tube can be parked for temporary storage while in use, or in the storage position when not in use. [9]

Accessories

To obtain the best performance and efficiency it is recommended that the correct nozzles are used for the main cleaning operations. These nozzles are indicated in the diagrams by the letters K.
A nozzle type K can be used to clean both carpet and hard floor.
The other nozzles are accessories for specialist cleaning tasks and are recommended for occasional use only.
All accessories can be fitted to the end of the handle or the end of the telescopic tube.

Accessory Set – Combines several functions in one, with maximum flexibility by the rotating body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly underneath the hose handle.
Crevice Nozzle – For corners and hard to reach areas. [E] Upholstery Brush – For soft furniture and fabrics. [F] Round Brush – For bookshelves, frames, keyboards and other delicate areas.
To extend the brushes push the button on the body of the tool. [G] Parquet Brush – For parquet floors and other delicate floors. [J] Pet Brush – Use the nozzle on stairs or for deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs removal. [I] IMPORTANT : Do not use mini turbo nozzles on rugs with long fringes, animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.

CLEANER MAINTENANCE

Replacing the Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.

1. Lift the bag door release latch to open the bag door, pull the bag holder and pull the pull the bag collar to remove the bag. [10,11]
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust bag should be disposed of correctly and carefully. [12,13]
3. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder.
4. Refit the bag holder and close the bag door.

WARNING : The bag door will NOT close if the dust bag and/or the bag holder are not assembled to the cleaner. Always ensure the bag and bag holder are present when closing the bag door.
REMEMBER : The bag check indicator may also be lit if an obstruction has occurred. In this case refer to ‘remove A Blockage from the System.

**Cleaning the Filters***
To maintain optimum performance of your cleaner, please wash the filters after each 5 bag changes.
Cleaning the pre-motor filter:

1. Lift the bag door release latch to open the bag door and remove the bag holder. [11]
2. Remove the pre-motor filter frame from the cleaner. [14]
3. Remove the filter sponge from the holder. [15]
4. Wash it in hand warm water, and allow it to dry thoroughly before replacing to the cleaner. [18, 19]

TROUBLESHOOTING

In case of malfunction, please refer to the following table

– Filter is blocked
– Brush duct is blocked
– Hasn’t been fully dried after washing| – Empty the dust bag in time
– Clean the sponge filter
– Clean the blockage
– Dry the sponge filter in cool place after washing
The machine does not work| -The power plugs are loose on the
socket or the power socket is not live
-The switch fails to be opened| – Inspect whether power plugs are tight or not or the socket is live or not
– Press the switch button
The machine suddenly stops| – The dust bag is full
– The sponge filter is blocked
– Suction inlet of brush or the other accessory is blocked| – Empty the dust bag in time
– Clean the sponge filter
– Clean the blockage

If the problem still can’t be solved, please contact local service center.

Importer: AB S.A. Adres: ul. Europejska
4, 55-040 Magnice, Polska
Manufacturer: Jiangsu Midea Cleaning Appliances Co., Ltd
No.39, Caohu Avenue, Xiangcheng Zone, Suzhou, China
Made in China

Documents / Resources

| Midea B8 MBC2080BB Bagged Vacuum Cleaner [pdf] Instruction Manual
B8 MBC2080BB Bagged Vacuum Cleaner, B8 MBC2080BB, Bagged Vacuum Cleaner, Vacuum Cleaner, Cleaner
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>