RUGGED RIDGE 13553.15 Roll Bar Top Installation Guide

: June 13, 2024
: RUGGED RIDGE

Table of Contents

RUGGED RIDGE 13553.15 Roll Bar Top
Product Information
13308.01).
Product Usage Instructions
13308.01)
INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RUGGED RIDGE 13553.15 Roll Bar Top

Product Information

Product Name : Roll Bar Top, YJ
Part Number : 13553.15
Manufacturer : Omix-ADA
Address: 460 Horizon Dr., Suwanee, GA 30024
Phone : 770-614-6101
Fax : 770-614-6069
Website : www.omix-ada.com

Included Components:

Brief
J-Clips

If your Wrangler does not have a soft top Windshield Channel, your installation requires the purchase of an aftermarket Windshield Channel (Part

13308.01).

Product Usage Instructions

Before you begin, the temperature of the Brief should be above 70 degrees Fahrenheit. We suggest laying the Brief in the sunlight for 1 hour before installation.
Locate the front edge and fold it over.
Place the Brief on top of the Jeep. Insert the folded edge into the Windshield Channel, working from one side of the vehicle to the other.
Locate the Velcro straps on each side of the roll bar. Wrap the flaps around the roll bar and fasten. Do both the driver and passenger sides of the vehicle.
Option 1 (with J-Clip):
Feed the rear corner straps through the J-Clips and place the J-Clip under a convenient attachment point, such as a rear corner rail or floor loop.
Wrap the straps around the roll bar or seat belt shoulder harness. Feed the loose end through the buckle and pull tight. Be sure not to interfere with the seat belts safety and operation. Place the strap under the seat belt. Never install over the seat belt strap.
Re-adjust Velcro and tighten all straps to ensure a wrinkle-free fit.
Option 2 (without J-Clip):
Wrap the straps around the seat belt shoulder harness and roll bar. Feed the loose end through the buckle on the other end and pull tight. Be sure not to interfere with the seat belts safety and operation. Place the strap under the seat belt. Never install over the seat belt strap.
Re-adjust Velcro and tighten all straps to ensure a wrinkle-free fit.

Included Components:

Brief
J-Clips

If your Wrangler does not have a soft top Windshield Channel, your installation requires the purchase of an aftermarket Windshield Channel (Part

13308.01)

INSTALLATION INSTRUCTIONS

Before you begin, the temperature of the Brief should be above 70 degrees Fahrenheit. We suggest laying the Brief in the sunlight for 1 hour before installation.

Locate the front edge and fold over (Figure 1).
Place the Brief on top of Jeep. Insert folded edge into Windshield Channel, working from one sideof vehicle to the other (Figures 2 & 3).
Locate the Velcro straps on each side of the roll bar. Wrap the flaps around the roll bar and fasten(Figures 4 & 5). Do both driver and passenger sides of the vehicle
NOTE : The rear straps can be fastened in two different methods:
Option 1 shows how to attach the Brief to your vehicle using J-Clips.
Option 2 shows how to attach the Brief to your vehicle around the rear shoulder seat belts.
Option 1 (with J-Clip)
Feed the rear corner straps through the J-Clips (Figure 6) and place the J-Clip under a convenientattachment point, such as a rear corner rail or floor loop (Figure 7).
Wrap the straps around the roll bar or seat beltshoulder harness. Feed the loose end through thebuckle and pull tight (Figure 8). Be sure not to interferewith the seat belts safety and operation. Place thestrap under the seat belt. Never install over the seatbelt strap.
Re-adjust Velcro and tighten all straps to assure a wrinkle-free fit.
Option 2 (without J-Clip)
Wrap the straps around the seat belt shoulderharness and roll bar. Feed the loose end through thebuckle on the other end and pull tight (Figure 9). Besure not to interfere with the seat belts safety andoperation. Place the strap under the seat belt.Never install over the seat belt strap.
Re-adjust Velcro and tighten all straps to assure a wrinkle-free fit.