KICHLER 52453BKT Homestead Vetivene Light Instruction Manual

: June 13, 2024
: KICHLER

Table of Contents

FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
CUSTOMERS SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52453BKT Homestead Vetivene Light

KICHLER 52453BKT Homestead Vetivene Light

FIXTURE DIAGRAM

PARTS LIST

[A] Canopy
[B] Safety Cable (Qty. 2)
[C] Outlet Box (not supplied)
[D] Mounting Strap
[E] Mounting Screw (Qty. 2)
[F] Lock Washer (Qty. 2)
[G] Lock Up Knob (Qty. 2)
[H] Loop (attached to Canopy)
[I] Strap Mounting Screw (Qty. 2)
[J] Locking Chain Link (Qty. 4)
[K] Chain (Qty. 2)
[L] Loop with Threaded Nipple
[M] Short Connecting Tube
[N] Connected Tubes and Loops (with fixture wires)
[O] Loop-Link-Loop Assembly
[P] Long Connecting Tube
[Q] Body
[R] Glass Shade (Qty. 8)
[S] Candle Sleeve with Plate (Qty. 8)
[T] Candle Sleeve Tool
[U] Candle Sleeve without Plate (Qty. 8)
[V] Socket

CAUTIONS

CAUTION – RISK OF SHOCK:

Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

On side of fixture with fixture wires, attach connected tubes and loops with fixture wires [N] to coupling on body [Q] by screwing tube into coupling.
NOTE: Thread locking compound must be applied to stem threads as noted with symbol (4) to prevent accidental rotation of fixture during cleaning, re- lamping, etc.
On side of fixture without fixture wires, attach long connecting tube [P] to other coupling on body [Q] by screwing long connecting tube into coupling. Attach loop-link-loop assembly [O] to top of long connecting tube [P] by screwing one of the loops into the end of the long connecting tube.
Attach short connecting tube [M] to loop-link-loop assembly [O] by screwing short connecting tube onto threads attached to top loop. Screw loop with threaded nipple attached [L] into free end of short connecting tube [M].
NOTE: Thread locking compound must be applied to all stem threads as noted with symbol (4) to prevent accidental rotation of fixture during cleaning, re-lamping, etc.
On side of fixture with fixture wires, attach locking chain link [J] to connected tubes and loops with fixture wires [N].
NOTE: Locking links can be opened and closed by threading the nut on and off locking chain link end.
On side of fixture without fixture wires, attach another locking chain link [J] to loop [L].
On side of fixture with fixture wires, attach chain [K] to locking chain link [J]. On side of fixture without fixture wires, attach other chain to other locking chain link.
On side of fixture with fixture wires, attach another locking chain link [J] to free end of chain. On side of fixture without fixture wires, attach last locking chain link to free end of other chain.
On side of fixture with fixture wires, attach top locking chain link [J] to loop attached to canopy [H].
On side of fixture without fixture wires, attach top locking chain link [J] to other loop attached to canopy [H].
On side of fixture with fixture wires, weave fixture wires through links of chain [K] no more than 3 inches apart, and pass fixture wires through locking chain link and through loop [H] into canopy [A].
Find appropriate threaded holes on mounting strap [D] that align with mounting screw holes near center of canopy [A]. Screw mounting screws [E] into threaded holes starting from the outlet box side.
Attach mounting strap to outlet box [C] using the strap mounting screws [I]. Mounting strap can be adjusted to suit position of fixture.
Loop safety cables [B] over the mounting strap and attach to mounting strap or inside of outlet box to secure in place and prevent damage to the wires during wiring.
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference chart below for correct connections and wire accordingly
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|
Raise fixture to ceiling, carefully passing mounting screws through mounting screw holes in canopy.
NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.
Use lock washers [F] and lock up knobs [G] to attach canopy to mounting strap. Tighten knobs to secure canopy in-place.
NOTE: This fixture has the option to install with or without glass shades [R]. If installing with glass shades, please follow steps #17, 18, and 20. If installing without glass shades, please follow steps #19 and 20.
If installing fixture with glass shades, carefully lower one glass shade [R] over a socket [V]. Make sure glass shade is fully seated in socket base cup.
While holding glass shade on socket base cup, carefully slip a candle sleeve with plate [S] over socket inside glass shade. Use candle sleeve tool [T] to carefully push candle sleeve down over socket. Make sure candle sleeve is pushed completely down so that it rests against the inside of the glass shade to secure glass shade in place, then remove candle sleeve tool. Repeat forewarning glass shades and sockets.
If installing fixture without glass shades, slip a candle sleeve without plate [U] down over socket. Carefully push candle sleeve completely down over socket so that it rests against the socket base cup. Repeat for remaining sockets.
Insert recommended bulbs (Not supplied).