munchkin MKFE0769-01 98 Degree Digital Bottle Warmer User Guide
- June 4, 2024
- munchkin
Table of Contents
Owner’s Guide
IMPORTANT SAFEGUARDS
WARNING : Strangulation hazard! Keep out of reach of children. Do not use extension cords.
When using electrical appliances, basic safety precautions should always be followed, including the following:
-
Read all instructions carefully before using your digital bottle warmer.
-
To protect against electrical shock, do not immerse the appliance, cord, or plug in water or any liquid. Clean with a damp cloth only. Avoid spillage on the connector.
-
For use by adults for intended purposes only. Any other use is inappropriate and dangerous. Keep out of the reach of children.
-
The appliance should be placed on a flat and stable area away from hot surfaces.
-
Do not let the cord hang over the edge of the table or counter or touch a hot surface.
-
Do not move the appliance when in use or if it contains hot water or liquid.
-
The warming chamber may become hot. Do not touch while in use and let cool before handling.
-
Ensure the baby bottle contents are at a safe temperature before feeding.
-
Use plastic baby bottles approved for boiling or glass thermo-resistant baby bottles with this appliance.
-
Do not use this product to heat frozen baby bottles.
-
Unplug from outlet when not in use and before cleaning. Allow cooling before putting on or taking off parts and before cleaning. Allow warmer to cool before cleaning.
-
Do not operate any appliance with a damaged cord or plug after the appliance malfunctions or has been damaged in any manner. Return appliance to Munchkin, Inc. for examination, repair, or adjustment.
-
The use of accessory attachments is not recommended by the appliance manufacturer and may cause injuries.
-
Do not place on or near a hot gas or electric burner, or in a heated oven.
-
Always attach the plug to the appliance first, then plug the cord into the wall outlet. To disconnect, turn any control to “off” then remove the plug from the wall outlet.
-
To disconnect, always make sure the unit is “off” before removing the plug from the wall outlet.
-
Do not use appliances for other than intended use.
-
Before serving the contents, unplug the cord from the wall outlet. Do not leave the cord within the child’s reach.
-
Close supervision is necessary when any appliance is used by or near children.
-
Extreme caution must be used when moving an appliance containing hot liquids.
-
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
-
A short power-supply cord (or detachable power-supply cord) should be used to reduce the risk resulting from becoming entangled in or tripping over a longer cord. Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use. If a longer detachable power-supply cord or extension cord is used:
a. The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance.
b. The cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally.
c. If the appliance is of the grounded type, the cord set or extension cord should be a grounding-type 3-wire cord. -
To be used with baby bottles only. May cause serious injury if used with any other vessel.
-
The heating element surface is subject to residual heat after use.
-
For household use only. Do not use outdoors.
-
Do not touch hot surfaces.
SAVE THESE INSTRUCTIONS
NOTE: These instructions are to be used as a guide only. Please note that there are many variables, such as the size of the baby bottle, ambient temperature, and starting temperature of the liquid, which can impact the speed as well as the final temperature at which this unit warms the liquid. Adjustments to the instructions below may be necessary. Always test the temperature of the liquid with a thermometer before feeding the baby. The food should not be heated for an extended amount of time.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to connect the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Included Parts
No adapter is necessary for:
- Avent Natural 4oz and 9oz*
- Evenflo Balance 5oz and 9oz*
Adapter A (with Gasket) for:
• Dr. Brown’s 4oz and 8oz
• Medela 5oz and 8oz
• Nuk First Essentials 5oz and 9oz
• EvenFlo Feeding Classic 4oz and 8oz
• Parents Choice 5oz and 9oz|
---|---
Adapter B (with Gasket) for:
• Tommee Tippee 5oz and 9oz|
Adapter C (with Gasket) for:
• Nuk Simply Natural 5oz and 9oz|
Adapter G (with Gasket) for:
• Comotomo 5oz and 8oz
• Olababy 4oz and 8oz
• Boon Nurse 4oz and 8oz|
WARNING: Do not use a glass baby bottle without an adapter.
*Dr. Brown’s, Medela, Nuk, EvenFlo, Parent’s Choice, Tommee Tippee, Avent, Comotomo, Olababy, and Boon Nurse are trademarks of their respective owners.
How to Use
BEFORE YOU BEGIN
FOR USE WITH ROOM-TEMPERATURE OR REFRIGERATED LIQUIDS ONLY. FROZEN BREAST MILK
MUST BE THAWED BEFORE USING THIS APPLIANCE.
The warmer should not be powered ON without a baby bottle filled with water or
breast milk installed on the warmer.
Warmer may overheat if used improperly.
Three dashes of “ _” on the front of the warmer indicate that the warmer’s
heating plate has overheated.
Under this scenario, you must wait 15 minutes before the unit is ready for
use.
-
Choose the correct adapter for your baby bottle (see Included Adapters on page 7).
Ensure the gaskets are installed in the warming unit and adapter (gasket identification letter facing up).
Screw the adapter into the neck of the warming unit.
If no adapter is needed, proceed to step 2. -
Fill the baby bottle with water (for formula) or breast milk.
NOTE : Warm water first, then mix in powdered formula once the heating cycle is complete.
For best results do not use heat premixed formulas or alternative milk. -
FLIP THE WARMING UNIT UPSIDE DOWN
and screw the baby bottle into the unit or adapter. Twist until the bottle is pressed firmly against the gasket to ensure a watertight seal. -
Open the rubber cover on the back of the warming unit, then insert the power cord. Plug the cord into an electrical outlet.
The standby mode is ready and the display will blink 00.0, it will automatically stop after 30 seconds if no action is taken.
NOTE : When the warmer turn off after 30 seconds of no activity. PRESS AND HOLD the button once for 2 seconds to activate the standby mode. Next PRESS and HOLD again for 2 seconds to activate the heating cycle.
-
Make sure the warming unit is right side up when standby mode is ready and then press and hold the power button for two seconds to start warming. The digital 98. C display will turn on.
-
When the liquid reaches approximately 98.6°F, the warming unit will beep to indicate the cycle is complete. The liquid will be kept at this temperature for up to 15 minutes after the cycle is complete. After 15 minutes, the warming unit will auto shut off.
NOTE : To ensure your liquid is warmed properly, wait until the end of the warming cycle before removing the bottle.
-
When ready to remove the bottle, press and hold the power button for two seconds to turn off the unit. Then unplug the cord from the unit and the wall outlet. Flip the device upside down, unscrew the baby bottle and shake the bottle well to ensure proper heat distribution.
Always check the liquid’s temperature before feeding.
NOTE : Warming a second bottle –Allow at least 5 minutes for the unit to cool before the next use.
ON/OFF: Press and hold for 2 seconds
WARMING TIMES
| VOLUME | STARTING MILK TEMPERATURE |
|---|---|
| 72°F (22°C) | 42°F (5°C) |
| 4oz/120ml | ~4 mins |
| 6oz/180ml | ~5 mins |
| 8oz/240ml | ~6.5 mins |
NOTE: Based on most common standard-sized bottles.
~4 mins means “approximately 4 minutes”
The warming durations are to be used as a guide only. Bottle style and size,
liquid starting temperature, and volume can impact the warming speed and final
temperature.
For optimal heating, and temperature uses 4oz to 8oz of liquid.
HOW TO CLEAN
Always unplug the unit and ensure that it is cool before cleaning. Do not use
scouring pads, abrasives, or solvents for cleaning; they may damage the
appliance and its surface. Place the rubber plug back into the plug attachment
to prevent water intrusion and cause electrical short during cleaning.
Digital Bottle Warmer: Wipe all surfaces with a damp cloth or sponge
using mild liquid soap, and rinse with clear water. Allow air-drying. Do not
submerge the unit in liquid.
Adapters and Gaskets: Wash with mild liquid soap and rinse with clear
water. Allow to air-dry. Always replace gaskets to their proper locations
(gasket identification letter facing up).
Keep Dust Cover on when not in use to keep the heating plate clean.
DE-SCALE
De-scale your bottle warmer after every use to ensure residual deposits are
removed from the heating plate and the silicone seal. To de-scale, mix 15ml
(0.5oz) of white vinegar with 15ml (0.5oz) of cold water and pour into the
heating plate. Allow liquid to stand in the unit until any deposits
(limescale) have dissolved. Discard liquid and wipe heating plate with a damp
cloth. Repeat process if necessary.
To avoid bacteria growth, perform “Cleaning” and “De-Scaling” after every use.
TROUBLESHOOTING
Blinking display: Digital Bottle Warmer will not operate if tilted more
than 30°. Place warmer on a flat and stable surface.
Overheat protection: The power switch turns off after three consecutive beeps
– circuit protection detects a rapid increase in internal temperature to
prevent damage to the device.
Three beeps: Digital Bottle Warmer will power off due to limescale
deposit build-up on the heating plate or if breast milk has not been mixed
thoroughly.
Display “E1″: Digital Bottle Warmer is not responding to input command
from the control panel due to not functioning temperature sensor.
The display shows “E2”: Digital Bottle Warmer is not responding to input
command from the control panel due to not functioning heating element.
For “E1” and “E2” errors, please contact our Customer Satisfaction team at
1-800-344-2229 (M-TH 8:00am-5:00pm
PST, F 8:00am-1:00pm PST) or visit our website at
www.munchkin.com.
Customer Service
TECHNICAL SPECIFICATIONS
- Product name: 98° Digital Bottle Warmer
- Model: MKFE0769-01
Electrical Rating:
- Input Voltage: 120VAC, 60Hz
- Wattage: 110W
- Warming unit dimensions: L3.3”(8.3 cm) x W3” (7.6 cm) x H3.4” (8.5 cm)
- Warming unit net weight: 0.4 lb(198g)
- Safety listings:
- CONFORMS TO UL STD. 1026
ONE-YEAR LIMITED WARRANTY
Munchkin’s 98° Digital Bottle Warmer includes a 1-year limited warranty
against defects from the date of purchase. In the event of a malfunction or
defect during the in-warranty period, Munchkin, Inc. at its option, will
replace or repair the product under warranty.
Upon receipt of the product and proof of purchase with a valid date of
purchase, the defective part will be immediately repaired or replaced and
returned to you free of charge (the USA only). Please send the defective unit,
proof of purchase, and a description of the problem you have encountered to:
Munchkin, Inc.
7835 Gloria Avenue
Van Nuys, CA 91406, USA
Attn: 98° Digital Bottle Warmer Warranty
NOTE : This warranty does not cover misuse, abuse, abnormal wear & tear,
negligence, environmental exposure, alteration, or accident. Any alteration or
removal of the product date code invalidates all claims against the
manufacturer.
CONTACT US
If you have any questions or wish to provide comments about this product, feel
free to contact our Customer Satisfaction team at
1-800-344-2229 (M-TH 8:00 am-5:00 pm
PST,
F 8:00am-1:00pm PST) or visit our website at
www.munchkin.com.
munchkin.com
800.344.2229
© 2021 MUNCHKIN, INC. 7835 GLORIA AVE., VAN NUYS, CA 91406.
WWW.MUNCHKIN.COM/PATENTS
MADE IN CHINA. 17555-IS-1
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>