HORIZON GLOBAL CQT76593 Class 3 Trailer Hitch Instruction Manual

HORIZON GLOBAL CQT76593 Class 3 Trailer Hitch

Product Information

The product is a hitch designed for towing purposes. It comes with a limited lifetime warranty. The hitch has a weight carrying capacity of 3500 lb (1589 kg) and a maximum tongue weight of 525 lb (238 kg). It is designed for use with specific vehicle models, including the Chevrolet Trax and Buick Encore.

Product Usage Instructions

1. Before installation, read and understand the installation instructions provided with the hitch. Keep them for future reference.
2. Also, review the instructions for your vehicle and any other accessories you plan to use with the hitch before using it.
3. During towing, keep the steering wheel as steady as possible. Do not apply brakes or speed up abruptly.
4. In case of any issues, the exclusive remedy under the warranty is product replacement. Any service or labor charges incurred in removing or replacing the product will not be covered.
5. Using the product for any purpose other than the specified use(s) stated in the product instructions is at your own risk.
6. This warranty is governed by the laws of the State of Michigan, and any disputes relating to this warranty will be addressed in the state courts located in Oakland County, Michigan.

Installation Instructions

• Installation Time: 40 min (average time for professional installers)

Equipment Required:

• Safety Glasses
• Ratchet
• 19 mm (11/16″) Sockets
• Torque Wrench
• Exhaust Removal Pliers
• Socket Soapy Extension water
• Wire Brush

Installation Steps:

1. Always wear safety glasses during the installation process.
2. Refer to the representative vehicle photo for guidance.
3. If needed, use the access hole and tape spacer to the hitch bracket.
4. Use the provided fastener kit (76593F) which includes carriage bolts, spacers, conical washers, and hex nuts.

Note: If you are not comfortable performing the installation on your own or need assistance, it is recommended to contact a professional installer.

For detailed step-by-step photo installation instructions, you can scan the QR code provided or visit the website: http://qr.towingproducts.net/qrproducts /qr-product

Installation Instructions
PART NUMBERS: 76593, 84593, CQT76593

Warning

To prevent SERIOUS INJURY, DEATH or PROPERTY DAMAGE:

• ALWAYS read, understand and follow warnings and instructions for your hitch BEFORE installation. Keep for future reference.
• DO NOT cut, weld or modify this receiver.
• CHECK all fasteners are tight and your hitch is securely mounted to your vehicle periodically.
• ALWAYS read, understand and follow all warnings and instructions for your vehicle and for other accessories you will use with your hitch BEFORE use.
• LOAD the trailer heavier in front.
• DO NOT exceed lower of towing vehicle manufacturer’s rating or:

• ALWAYS wear your seatbelt.
• SLOW DOWN when towing, NEVER exceed any posted speed limit.
•  If EXCESS SWAY occurs, take your foot off the gas pedal and hold the steering wheel as steady as possible. DO NOT apply your brakes and DO NOT speed up.

Applications

• *Visit our website for the most up to date information regarding application years and trim levels.

Installation Time: 40 min
The time listed above is the average time for professional installers. If you do not feel comfortable performing this installation on your own or are in need of assistance, please contact a professional installer.

Equipment Required

Representative Vehicle Photo

Hitch Illustration

DO NOT EXCEED LOWER OF TOWING VEHICLE MANUFACTURER’S RATING OR:

Always wear SAFETY GLASSES when installing hitch

Fastener Kit: 76593F

1. Insert the pull wires ⑤ into the frame rails and use them to feed the carriage bolts ① and spacers ② into frame rails through access holes as shown in Figure 2. Leave pull wires attached.
   Note: Driver side rear attachment – vehicle frame could have weldnut if frame has weldnut see note in step 4.

2.  Lower exhaust system at (2) rubber isolators. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Use exhaust support stand to prevent damaging muffler.

3. Add (1) spacer ② to flange on drivers side bracket as shown in figure 3. Raise the hitch into position and slide it over the top of exhaust pipe on passenger side first. Feed the pull wires through the slots in the brackets. Note: Bevel washer ⑧ is needed on drivers side rear attachment if there is a gap between vehicle frame and hitch.

4. Remove pull wires and loosely install conical washer ③ and hex nut ④ to the hitch. Note: If there is a weldnut on the driver side frame, use M12 bolt ⑥ and conical washer ⑦ instead.

5. Tighten all 7/16’’-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 NM) and all M12-1.75 CL8.8 fasteners to 68 Lb.-Ft. (92 NM)
   Proper torque is needed to keep the hitch secure to the vehicle when towing.

6. Reinstall the exhaust at the rubber isolators.
   Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.

Installation Instructions

1. Insert the pull wires ⑤ into the frame rails and use them to feed the carriage bolts ① and spacers ② into frame rails through access holes as shown in Figure 2. Leave pull wires attached. Note: Drivers side rear attachment – vehicle frame could have weldnut if frame has weldnut see note in step 4.

2. Lower exhaust system at (2) rubber isolators. Spraying a lubricant or soapy water on the metal hanger rod and the rubber isolator helps removal. Use exhaust support stand to prevent damaging muffler.

3. Add (1) spacer ② to flange on drivers side bracket as shown in figure 3. Raise the hitch into position and slide it over the top of exhaust pipe on passenger side first. Feed the pull wires through the slots in the brackets. Note: Bevel washer ⑧ is needed on drivers side rear attachment if there is a gap between vehicle frame and hitch.

4. Remove pull wires and loosely install conical washer ③ and hex nut ④ to the hitch. Note: If there is a weldnut on the driver side frame, use M12 bolt ⑥ and conical washer ⑦ instead.

5. Tighten all 7/16’’-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 NM) and all M12-1.75 CL8.8 fasteners to 68 Lb.-Ft. (92 NM)
   Proper torque is needed to keep the hitch secure to the vehicle when towing .

6. Reinstall the exhaust at the rubber isolators.

LIMITED LIFETIME WARRANTY

1. Limited Lifetime Warranty (“Warranty”). Cequent Performance Products, Inc. (“We”, “Us” or “Our”) warrants to the original consumer purchaser only (“You” or “Your”) that the product will be free from material defects in both material and workmanship, ordinary wear and tear excepted. The Warranty is valid only if (a) the products are returned to Us for inspection and testing; (b) Our inspection discloses to Our satisfaction that any alleged nonconformance are material and have not been caused by misuse, neglect, wear and tear, improper installation, unsuitable storage, improper repair, alteration, or accident; and (c) the products were installed, maintained and used in accordance with Our instructions. THE WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (OTHER THAN THE WARRANTY OF TITLE AS PROVIDED BY THE UNIFORM COMMERCIAL CODE IN EFFECT IN MICHIGAN), INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SAID WARRANTIES BEING EXPRESSLY DISCLAIMED.
2. Obligations of Purchaser. To make a Warranty claim, contact Us at our principal address of 47912 Halyard Drive, Suite 100, Plymouth, MI 48170, 1-800-632-3290, identify the product by model number, and follow the claim instructions that will be provided. Any returned product that is replaced by Us becomes our property. You may be responsible for return shipping costs. Please retain your purchase receipt to verify date of purchase and that You are the original consumer purchaser. The product and the purchase receipt must be provided to Us in order to process Your Warranty claim.
3. Exclusive Remedy. Product replacement is Your sole and exclusive remedy under this Warranty. We shall not be liable for service or labor charges incurred in removing or replacing a product. IN NO EVENT WILL WE BE RESPONSIBLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES.
4. Assumption of Risk. You acknowledge and agree that any use of the product for any purpose other than the specified use(s) stated in the product instructions is at Your own risk.
5. Governing Law. This Warranty gives You specific legal rights, and You also may have other rights which vary from state to state. This Warranty is governed by the laws of the State of Michigan, without regard to rules pertaining to conflicts of law. The state courts located in Oakland County, Michigan shall have exclusive jurisdiction for any disputes relating to this Warranty.
   Rev 9/2014

Scan for safe towing tip, or visithttp://qr.towingproducts.net/qrproducts/qr-product

• Website: www.horizonglobal.com
• Technical Assistance : 800-632-3290
• TechnicalSupport@horizonglobal.com

References

• ducts.net/qrproduct
• Horizon Global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>