IKEA 004.439.03 TINAD Integrated Fridge Instruction Manual

IKEA 004.439.03 TINAD Integrated Fridge

INSTRUCTIONS

Product description

1. Glass shelves
2. Control panel with LED light
3. Bottle rack
4. Rating plate (at the side of the crisper)
5. Crisper
6. Dairy balcony with lid
7. Double balcony
8. Door balcony
9. Dividers
10. Bottle holder
11. Bottle balco

Characteristics, technical data and images may vary according to the model.

Accessories

EGG tray

First use

Connect the appliance to the power supply. The ideal food storage temperatures are already factory-set (intermediate).
Note: after being switched on, the appliance needs 4-5 hours in order to reach the correct temperature to store a typical volume of food.

Important!
This appliance is sold in France. In accordance with regulations valid in this country it must be provided with a special device (see figure) placed in the lower compartment of the fridge to indicate the coldest zone of it.

Daily use

Refrigerator and freezer operation

• The appliance’s refrigerator compartment features a control panel with LED lights.
• A different temperature can be set using the C button as shown in the figure.
• The three green LED indicators indicate the refrigerator compartment set temperature.
• The following adjustments are possible:

Stand-by

• Press the C button for 3 seconds to deactivate the appliance (the control panel and lights remain off).
• Press the button again briefly to reactivate the appliance.
• Note: This operation does not disconnect the appliance from the power supply.
• Note: the ambient temperature, frequency of door opening and position of the appliance can affect the temperature inside the two compartments. These factors must be taken into account when setting the thermostat. A Led light
  B Refrigerator compartment temperature
  C Button for temperature regulation and Stand-by function
  LED light
  LEDs last longer than traditional light bulbs, improve internal visibility and are environmentally friendly.
  To avoid food waste, please refer to the recommended setting (Intermediate), and storage times found in the user manual.

Installation

• The appliance must be handled and installed by two or more persons – risk of injury. Use protective gloves to unpack and install – risk of cuts.
• Installation, including water supply (if any), electrical connections and repairs must be carried out by a qualified technician. Do not repair or replace any part of the appliance
• unless specifically stated in the user manual. Keep children away from the installation site. After unpacking the appliance, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest Aftersales Service. Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of reach of children – risk of suffocation. The appliance must be disconnected from the power supply before any
• installation operation – risk of electric shock. During installation, make sure the appliance does not damage the power cable – risk of fire or electric shock. Only activate the appliance when the installation has been completed.
• Be careful not to damage the floors (e.g. parquet) when moving the appliance. Install the appliance on a floor or support strong enough to take its weight and in a place suitable for its size and use. Make sure the appliance is not near a heat source and that the four feet are stable and resting on the floor, adjusting them as required, and check that the appliance is perfectly level using a spirit level. Wait at least two hours before switching the appliance on, to ensure that the refrigerant circuit is fully efficient.
• WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
• When contacting our Service Provider, please state the codes provided on your product’s identification plate.The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model identifier that can be used to consult the https://eprel.ec.europa.eu database portal.
• WARNING: To avoid a hazard due to instability, positioning or fixing of the appliance must be done in accordance with the manufacturer instructions. It’s forbidden to place the refrigerator in such way that the metal hose of gas stove, metal gas or water pipes, or electrical wires are in contact with the refrigerator back wall (condenser coil).
• To guarantee adequate ventilation, leave a space on both sides and above the appliance. The distance between the rear of the appliance and the wall behind the appliance should be 50 mm, to avoid access to hot surfaces. A reduction of this space will increase the Energy consumption of product. Please remove the power cord from condenser hook during installation before connecting product to power supply.

General information

The drawers, baskets and shelves should be kept in their current position unless otherwise specified in this quick guide. The light system inside the refrigerator compartment uses LED lights, allowing for better lighting than with traditional light bulbs, as  well as for very low energy consumption. Doors and lids of the refrigeration appliance should be removed before disposal in the landfill, to avoid children or animals getting trapped inside.

Technical data

References

• Hej! Welcome to IKEA Global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>