JAMARA 413117 Charger for Akkupacks Instructions

: June 13, 2024
: JAMARA

Table of Contents

JAMARA 413117 Charger for Akkupacks
Product Information
Product Usage Instructions
General information
Certificate of Conformity
Technical data
Highlights
DESCRIPTION
Charging a battery
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JAMARA 413117 Charger for Akkupacks

JAMARA-413117-Charger-for-Akkupacks-PRODUCT

Product Information

The Lipo 20 Charger 2S/3S, No. 413117 is a product manufactured by JAMARA e.K. It is a charger designed specifically for lithium polymer batteries with XH balancer connectors. The charger has a power input range of AC 100 – 240V and operates at a frequency of 50/60Hz. It has an output of 8.4V for 2S (7.4V) batteries and 12.6V for 3S (11.1V) batteries. The charging current is 1.6A, and themaximum power output is 20W.
The charger comes with status LEDs to indicate the charging status of the battery. It is important to note that only one battery can be connected to the charger at a time. Charging multiple batteries simultaneously can cause damage to the battery or charger and poses a fire hazard.
It is crucial to use lithium polymer batteries with XH balancer connectors that are approved by the battery manufacturer. The battery capacity should be at least 1600mAh to prevent the risk of fire due to excessive charging current. If using batteries with a capacity below 1600mAh, they must be approved for a charging current of 1600mA (Speedcharging).

Product Usage Instructions

Plug the power cord of the charger into a suitable socket.
The LEDs on the charger will light up green, indicating that the charger is ready for charging.
Connect the lithium polymer battery with an XH balancer connector to the appropriate slot on the charger. Use either the 2S Balancer slot for 2S (7.4V) batteries or the 3S Balancer slot for 3S (11.1V) batteries.
Observe the status LEDs on the charger:
- If the LEDs turn red for a few seconds and then turn green again, it means that the battery is fully charged.
- If the LEDs remain green when an empty battery is connected, there may be a defect in the battery such as a cell defect or deep discharge. In this case, immediately disconnect the battery from the charger and use another battery.
After charging is complete, unplug the charger from the power socket.

Remember to dispose of electrical appliances and batteries separately according to local regulations. If personal data is stored on the electrical appliance, ensure to remove them before disposal.

General information

JAMARA e.K. is not liable for any damage caused to the product itself or through this, provided this is due to improper operation or handling errors. The Customer alone bears the full responsibility for the proper use and handling, including without limitation, the assembly, the charging process, the use and choice of the operation area. Please refer to the operating and user instructions, it contains important information and warnings.

Certificate of Conformity

Hereby JAMARA e.K. declares that the product „LiPo 20 Charger 2S/3S, No. 413117“ complies with Directive 2014/30/EU, 2014/35/EU and 2011/65/EU. The full text of the EU Declaration of Conformity is available at the following Internet address:
www.jamara-shop.com/Conformity
Read the complete instructions and security instructions carefully before using the model.
Caution! Please fully and carefully read warnings/ safety instructions. These are for our own security and can avoid accidents/injuries.

Technical data

Input: AC 100 – 240V | 50/60Hz | 25W
Output: 8,4 V (2S 7,4 V) / 12,6 V (3S 11,1 V)
Battery types/Cells LiPo / 2S 7,4 V; 3S 11,1 V
Charging current: 1,6 A | 20 W

Highlights

Integrated charge balancer for 2 to 3 lipo cells
Maximum safety (does not charge deeply discharged cells)
Charging current up to 20 Watt at 1.6Ampere
Automatic charge stop when final charge voltage is reached
Supports 2S;7.4V and 3S;11.1V lithium polymer batteries with XH connector from 1600mAh
2 colored status LED‘s

Important notes on the suitability of the battery:

Make sure to use only lithium polymer batteries with XH balancer connector. Only these may be used with the charger. Other connections and battery types must not be used (fire hazard due to reverse polarity or overcharging may result).
Please contact the manufacturer of your battery to find out whether your battery is suitable. Only LiPo batteries with a capacity of at least 1600mAh must be used (otherwise there is a risk of fire due to excessive charging current). If you use batteries with a capacity below 1600mAh, the batteries must be approved for a charging current of 1600mA (Speedcharging). Please ask the manufacturer of your battery if your battery meets these requirements.
You may only connect one single battery to the charger at a time. Charging 2 batteries at the same time is NOT allowed and will cause damage to the battery or charger (fire hazard).

DESCRIPTION

$JAMARA-413117-Charger-for-Akkupacks-FIG- $1$$

Power Slot 100 – 240 V
2S Balancer
3S Balancer
Status LEDs

Charging a battery

$JAMARA-413117-Charger-for-Akkupacks-FIG- $2$$

Plug the power cord of the charger into a suitable socket. The LEDS light up green and indicate that the charger is ready for charging.
Now connect the empty battery to the charger. 7.4V 2S batteries to the 3 pin connector or 11.1V 3S batteries to the 4 pin connector. Do not use force and pay attention to reverse polarity. The LEDs change to red after a few seconds and indicate that the battery cells are charging.

Attention:

When connecting a 2S battery, only the first 2 LEDs (Cell1-2) change to red, LED 3 (Cell 3) will remain green. When 3S batteries are connected, all LEDs are red (Cell1-3). As soon as a the battery cell is full, the corresponding LED changes to green. Because the cells are charged individually in a balanced way, it is possible that one cell is fully charged earlier than the others. Always leave the battery on the charger until all connected cells are fully charged (green) to allow the charger to balance your battery

Detecting a full battery.
When you connect a full battery to the charger, the LEDs will turn red for a few seconds and then turn green again. This means that the battery is already fully charged.

Detecting a defective battery.
If the LEDs remain green when an empty battery is connected, there is a defect in the battery (cell defect or deep discharge). In this case, immediately disconnect the battery from the charger and use another battery.

Safety Information

Charging may only be carried out by adults
Only for indoor use.
Never expose the charger to dust, dirt, moisture and direct sun light.
After use always disconnect the charger from the power source and remove any connected batteries.
Do not open the charger to do repairs. This will void the guarantee and may be dangerous. If the charger is damaged or faulty, return it to our service department for repairs.
Follow the instructions of the battery manufacturer

Disposal restrictions

Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. You are obliged to take out the batteries, if possible, and to dispose of the electrical equipment at the communal collection points. Should personal data be stored on the electrical appliance you must remove them by yourself

Service centre

Mooser T-Trade, Thomas Mooser, Bürgermeister-Koch-Str. 32a, DE-82178 Puchheim, Tel +49 (0) 89 17929867, Fax +49 (0) 89 17929869, info@mooser-t-trade.de,
www.mooser-t-trade.de
JAMARA e.K. Inh. Manuel Natterer Am Lauerbühl 5 – DE-88317 Aichstetten
Tel. +49 (0) 75 65/94 12-0 –
Fax +49 (0) 75 65/94 12-23
info@jamara.com
www.jamara.com
Service – Tel. +49 (0) 75 65/94 12-777
service@jamara.com