JAMARA SCX 2,4 GHz Transmitter User Manual
- October 27, 2023
- JAMARA
Table of Contents
SCX 2,4 GHz Transmitter
User Manual
General information
Jamara e.K. is not liable for any damage caused to the product itself or through this, provided this is due to improper operation or handling errors. The Customer alone bears the full responsibility for the proper use and handling, including without limitation, the assembly, the charging process, the use and choice of the operation area. Please refer to the operating and user instructions, it contains important information and warnings.
Certificate of Conformity
Hereby JAMARA e.K. declares that the product “SCX 2,4 GHz, No. 061172“
complies with Directive 2014/53/EU, 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the
following Internet address: www.jamara-shop.com/Conformity
For model building only – Not a toy!
Read the complete instructions and security instructions carefully before
using the model.
Caution! Please fully and carefully read warnings/ safety instructions.
These are for our own security and can avoid accidents/injuries.
Box contents:
- Transmitter
- Receiver
- Instruction
Recommended Accessories
8 x AA Batteries
Ord. No. 140267 (4 pieces)
Features:
- 2 Channel 2,4 GHz Tranmitter
- 3 Channel 2,4 GHz Receiver
- 2 Servo Reverse
- 2 Trim Sliders
- Charging socket
- Programmable fail-safe on the receiver
Technical data:
| Frequency | 2,4 GHz |
|---|---|
| Modulation | GFSK |
| Servo resolution | 10 Bit (1024 Steps) |
| Model types | Car, boat |
| Functions | 2 channel |
| Temperature range | – 15 to + 58° C |
| Receiver antenna length | ~ 26 cm |
| Operating voltage | 12 V DC (8 cells) |
| Charging | Via charging socket |
| Size | ~ 190 x 210 x 81 mm |
| Weight | ~ 700 g |
Receiver SCX 2,4 GHz
Ord.No. 06 1171
| Frequency | 2,4 GHz |
|---|---|
| Modulation | GFSK |
| Servo resolution | 10 Bit (1024 steps) |
| Operating voltage | 4,5 – 7,4 V DC |
| Size | ~ 38 x 22 x 13 mm |
| Weight | ~ 11 g |
| Range | ~ 400 m |
Following should be strictly adhered to:
- Before Switching on the system ensure that throttle stick is in the off position.
- Check that the transmitter and receiver are compatible and bonded to one another.
- Always switch the transmitter on first and then the receiver.
- Always switch the receiver off first and then the transmitter .
- Complete a full range and function test before every take-off .
- Never over-fly people and do not allow your model to endanger people or animals.
- Do not fly near to over-head cables, buildings or airfields.
- The system must not be operated in rain, or thunder storms.
- If you do not intend to use the transmitter for a long period, remove the batteries.
Transmitter
- Antenna
- Handle
- Power LED
- Servo Reverse CH 1
- Left/Right Stick
- Left/Right Trim
- Binding Button
- ON/OFF Switch
- Throttle Stick
- Throttle Trim
- Servo Reverse CH 2
- Indicator LED
Battery Hatch
The battery hatch is located on the rear side of the transmitter and to open
it simply push down on the position marked ‚Push‘ and slide the cover away.
When fitting the batteries always be very careful not to short circuit them by
observing the correct polarity.
Receiver
2 Servos can be connected directly to the receiver.
Receiver Channel Allocation:
Channel 1: Steering
Channel 2: Throttle
Binding Channel 3: Binding Cable
Binding
As with all 2,4 GHz systems the transmitter and the receiver must be bound
together and this process is vital. Before the system is bound together it
will not function and therefore cannot be used and so the following steps
must be followed before you attempt to operate the system:
-
Fit the binding plug to socket 3 on the receiver and connect the power supply.
The receiver LED will begin to blink: -
Press and hold down the binding button on the transmitter and switch the power on.
This will put the transmitter into binding mode. -
Once the binding process has finished the LED will shine.
-
Switch the transmitter and receiver off.
-
Remove the binding plug.
Important Information
The system will not function whilst the binding button is pressed. Also, the system should not be left in binding mode for long periods of time.
Settings
Before you operate your model carefully check that the servo operate in the correct direction. If they do not rotate in the correct direction use the servo reverse switches located on the front of the transmitter to change the direction. The servo neutral positions should then be set by moving the servo arms until they are at exactly 90 0 with the trim central. The trim should only be used to make fine adjustments when operating the model. If you are using this system with an Internal Combustion engine make sure that the linkage cannot bind in either the full throttle or tick-over positions.
Switching On
- Connect all of the components together.
- Switch ion the transmitter.
- Connect the power supply to the receiver and switch on if required.
- Check that all of the LEDs are correctly illuminated.
- The system is now switched on and ready to operate.
Switching Off
- Switch off and unplug the receiver power supply.
- Switch off the transmitter.
Operating The Model
Steering
This function is used to steer the model in the correct direction. Moving the
steering stick to the left or right will make the wheels, or hull if operating
a boat, move in that direction. Moving the stick to the left should make the
model steer to the left.
Throttle
This function is used to make the model move forward or in revers and it also
is used to control the model‘s speed. Pushing the stick forwards makes the
model accelerate forwards and pulling it to the rear will make the model
brake first and then to accelerate in reverse.
Disposal restrictions
Electrical appliances must not be disposed of in domestic waste and must be
disposed of separately.
You are obliged to take out the batteries, if possible, and to dispose of the
electrical equipment at the communal collection points. Should personal data
be stored on the electrical appliance you must remove them by yourself.
Modellbau Zentral
Peter Hofer
Bresteneggstrasse 2
CH-6460 Altdorf
Tel +41 79 429 62 25
Mobil. +41 41 870 02 13
Mail info@modellbau-zentral.ch
Web www.modellbau-zentral.ch
All rights reserved. Copyright JAMARA e.K. 2021
Copying or reproduction in whole or part, only with the expressed permission
of JAMARA e.K.
Coupon
Order the current catalogue with our complete assortment of modelling goods today.
Name……………………………………………………..
First name………………………………………………
Street……………………………………………………..
City………………………………………………………….
Phone…………………………………………………
E-mail……………………………………………….
Please send the catalogue to the following specialist dealer:
Your dealer…………………………………………………..
We will include a catalogue for your attention with the next order placed by
your dealer.
info@jamara.com
www.jamara.com
Service – Tel. +49 (0) 75 65/94 12-777
kundenservice@jamara.com
References
- jamara.com
- Bygg din unike bokhylle ved å kombinere ulike seksjoner.
- Herzlich willkommen bei der Bay-Tec Modelltechnik!
- jamara.com
- Modellbau Zentral - Peter Hofer - Altdorf UR
- Reitter Modellbau & Robotics - Zubehör, Ersatzteile, Bausätze
- e-dite.cz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>