JAMARA SCX 2, 4 GHz Transmitter Instructions

: October 27, 2023
: JAMARA

Table of Contents

JAMARA SCX 2, 4 GHz Transmitter
General information
Certificate of Conformity
Box contents
Features
Technical data
Technical data
Transmitter
Operating The Model
Coupon
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JAMARA SCX 2, 4 GHz Transmitter

JAMARA SCX 2, 4 GHz Transmitter product

General information

JAMARA e.K. is not liable for any damage caused to the product itself or by it, if this is due to impro-per operation or handling errors. The customer alone bears the full responsibility for the proper use and handling, including in particular, assembling, charging and using the model, and selecting the area in which to use it. Please refer to the operating and user instructions, which contain important information and warnings.

Certificate of Conformity

Hereby JAMARA e.K. declares that the product “SCX 2,4 GHz, No. 061172“ complies with Directive 2014/53/EU, 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address:www. jamara-shop.com/Conformity

For model building only – Not a toy!
Read the complete instructions and security instructions carefully before using the model.
Caution: Please fully and carefully read warnings/ safety instructions. These are for our own security and can avoid accidents/injuries.

Box contents

Transmitter
Receiver
Instruction

Recommended Accessories

8 x AA Batteries
Ord. No. 140267 (4 pieces)

Features

2 Channel 2,4 GHz Tranmitter
3 Channel 2,4 GHz Receiver
2 Servo Reverse
2 Trim Sliders
Charging socket
Programmable fail-safe on the receiver

Technical data

Frequency: 2,4 GHz
Modulation: GFSK
Servo resolution: 10 Bit (1024 Steps)
Model types: Car, boat
Functions: 2/4 channel
Temperature range: – 15 to + 58° C
Receiver antenna length: ~ 26 cm
Operating voltage: 12 V DC (8 cells)
Charging Via: charging socket
Size: ~ 190 x 210 x 81 mm
Weight: ~ 700 g

Receiver SCX 2,4 GHz:
Ord.No. 06 1171

Technical data

Frequency: 2,4 GHz
Modulation: GFSK
Servo resolution: 10 Bit (1024 steps)
Operating voltage: 4,5 – 7,4 V DC
Size: ~ 38 x 22 x 13 mm
Weight: ~ 11 g
Range: ~ 400 m

Following should be strictly adhered to:

Before Switching on the system ensure that throttle stick is in the off position.
Check that the transmitter and receiver are compatible and bonded to one another.
Always switch the transmitter on first and then the receiver.
Always switch the receiver off first and then the transmitter .
Complete a full range and function test before every take-off .
Never over-fly people and do not allow your model to endanger people or animals.
Do not fly near to over-head cables, buildings or airfields.
The system must not be operated in rain, or thunder storms.
If you do not intend to use the transmitter for a long period, remove the batteries.

Transmitter

Antenna
Handle
Power LED
Servo Reverse CH 1
Left/Right Stick
Left/Right Trim
Binding Button
ON/OFF Switch
Throttle Stick
Throttle Trim
Servo Reverse CH 2
Indicator LED

Battery Hatch
The battery hatch is located on the rear side of the transmitter and to open it simply push down on the position marked ‚Push‘ and slide the cover away. When fitting the batteries al-ways be very careful not to short circuit them by observing the correct polarity.
Receiver
2 Servos can be connected directly to the receiver.
Receiver Channel Allocation:

Channel 1: Steering
Channel 2: Throttle
Binding Channel 3: Binding Cable

Binding
As with all 2,4 GHz systems the transmitter and the receiver must be bound together and this process is vital. Before the system is bound together it will not function and therefore cannot be used and so the following steps must be followed before you attempt to operate the system:

Fit the binding plug to socket 3 on the receiver and connect the power supply.
The receiver LED will begin to blink:
Press and hold down the binding button on the transmitter and switch the power on. This will put the transmitter into binding mode.
Once the binding process has finished the LED will shine.
Switch the transmitter and receiver off.
Remove the binding plug.

Important Information
The system will not function whilst the binding button is pressed. Also, the system should not be left in binding mode for long periods of time.

Settings
Before you operate your model carefully check that the servo operate in the correct direction. If they do not rotate in the correct direction use the servo reverse switches located on the front of the transmitter to change the direction. The servo neutral positions should then be set by moving the servo arms until they are at exactly 900 with the trim central. The trim should only be used to make fine adjustments when operating the model. If you are using this system with an Internal Combustion engine make sure that the linkage cannot bind in either the full throttle or tick-over positions.

Switching On

Connect all of the components together.
Switch ion the transmitter.
Connect the power supply to the receiver and switch on if required.
Check that all of the LEDs are correctly illuminated.
The system is now switched on and ready to operate.

Switching Off

Switch off and unplug the receiver power supply.
Switch off the transmitter.

Operating The Model

Steering
This function is used to steer the model in the correct direction. Moving the steering stick to the left or right will make the wheels, or hull if operating a boat, move in that direction. Moving the stick to the left should make the model steer to the left.

Throttle
This function is used to make the model move forward or in revers and it also is used to control the model‘s speed. Pushing the stick forwards makes the model accelerate forwards and pulling it to the rear will make the model brake first and then to accelerate in reverse.

Disposal restrictions
Electrical appliances must not be disposed of in domestic waste and must be disposed of separately. You are obliged to take out the batteries, if possible, and to dispose of the electrical equipment at the communal collection points. Should personal data be stored on the electrical appliance you must remove them by yourself.