LOGOSOL B751 Band Sawmill with 4.6 kW Electric Motor User Manual

LOGOSOL B751 Band Sawmill with 4.6 kW Electric Motor

Product Information

The product is an electric motor designed for use with the Logosol band sawmill.

• There are two options available: a 4.6 kW electric motor and an 8 kW electric motor.
• The motors are supplied with different voltage options: 400V and 230V.

Product Usage Instructions

1. Before using the saw, carefully read and understand the user manual for the band sawmill to which the electric motor will be installed.
2. Start by installing the motor on the motor shelf. Follow the assembly instructions provided in the manual.
3. Install the safety hinge in the existing holes.
4. Mount the pulley on the motor shaft, ensuring it fits on the key. Secure the pulley with the stop screw.
5. Fit the switch box on the handle tube.
6. Place the drive belt over the wheel and pulley.
7. To turn on the power supply to the machine, turn the dead man’s switch to (1).
8. To start the motor, hold down the dead man’s switch (button on the right) and press the start button (on the left). Release the left button once the motor has started. The motor will run until the dead man’s switch is released.
9. Once the motor installation is complete, refer back to the band sawmill manual and continue with the setup sequence as indicated in the instructions.

Note:
It is important to adjust the saw head before starting to ensure satisfactory sawing and correct functioning of the sawmill. Follow the setup sequence carefully, as certain adjustments may affect other machine settings.

This manual describes the installation of the electric motor for the Logosol band sawmill. Please see the user manual for your band sawmill for information on assembly, settings, and safety instructions.

PACK SUPPLIED

• 8400-000-0070
  4.6 kW electric motor, 400V

• 8400-000-0074
  4.6 kW electric motor, 230V

• 8400-000-0072
  8 kW electric motor, 400V

• 8400-000-0076
  8 kW electric motor, 230V

FINAL SAW HEAD ASSEMBLY, 4.6 / 8 KW ELECTRIC MOTOR

• Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
• Numbering for installation sequence
• After assembly, follow the instructions under the Setup sequence in the sawmill manual to complete the setup before starting the machine.

ELECTRIC MOTOR

ELECTRIC MOTOR 4.6/8 KW

1. The electric motor comes with a hinge switch connected. Assembly consists of installing the motor on the motor shelf, as well as mounting the pulley and drive belt. The illustration shows the hole pattern for installing the 4.6 / 8 kW electric motor. Follow the assembly instructions, then run through the setup sequence for the machine when the assembly is complete. Install the motor on the motor shelf.
   Top view:

2. Now install the safety hinge in the existing holes.

3. Install the pulley on the shaft so that it fits on the key. Then secure the pulley with the stop screw.

4. Fit the switch box on the handle tube.

5. Fit the drive belt over the wheel and pulley.

TURN ON/OFF THE SWITCH BOX

Turn the dead man’s switch to (1) to turn on the power supply to the machine.

START THE MOTOR

Hold down the dead man’s switch (button on the right) to start the motor. Then press the start button (on the left). You can release the left button when the motor has started. The motor will now run until the dead man’s switch is released.

Well done!
Now you have finished installing the motor, go back to the manual for your band sawmill and carry on with the setup sequence, starting at the point as indicated in the instructions below.

SETUP SEQUENCE

• Read through all the set-up instructions before starting to set up, then follow the instructions step by step as you work.
• IMPORTANT!
  It is important to adjust the saw head before starting to ensure satisfactory sawing and the correct functioning of the sawmill. Follow the setup sequence carefully! Certain adjustments affect other machine settings.

Contact Information

• Fiskaregatan 2, SE-871 33 Härnösand, Sweden 0611-182 85
• info@logosol.se.
• www.logosol.se.

References

• Chain Sawmills, Band Sawmills and Woodworking Machinery | LOGOSOL
• Sågverk, bandsåg, mobila sågverk & hyvlar för ditt snickeri | LOGOSOL | LOGOSOL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>