Fab Fours G5252 Rock Slider for 2021 Ford Bronco Owner’s Manual
- June 13, 2024
- Fab Fours
Table of Contents
G5252 Rock Slider for 2021 Ford Bronco
Installation manual
Tube Sliders 2dr
Product number: G5252
Application: 2021 ford bronco
IMPORTANT SAFETY GUIDE | Your safety and the safety of others is very important.
In order to help you make informed decisions about safety, we have provided the following warnings, safety precautions, installation instructions, and other important information to alert you to potential hazards that could hurt you or others.
Please do a job safety analysis before each task to identify potential hazards for your situation and remove/protect against them. Use own good judgment and take your time.
Check packaged materials immediately upon arrival to ensure that all listed parts are included and undamaged.
Read and understand all warnings, safety precautions, and instructions before installing this product.
SENSORS FIELD OF VIEW MAY BE ALTERED WITH USE OF THE REPLACEMENT BUMPER.
WARNINGS
- Failure to observe the following warnings and instructions provided in this manual could lead to severe injury and/or death.
- For professional installation only. Careless installation and/or operation can result in serious injury, death, and/or equipment damage. All liability for installation and use rests with the user or consumer.
- Fab Fours, Inc. only approves installing this product according to these written instructions with the hardware provided. Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to, using alternative installation methods, hardware, or materials.
- This product is for off road use only.
SAFETY / DISCLAIMER
- Always remove jewelry and wear eye protection.
- Always use extreme caution when jacking up a vehicle for work. Set emergency brake and use tire blocks. Locate and use the vehicle manufacturers designated lifting points. Use jack stands.
- Always use appropriate and adequate care in lifting components into place.
- Always ensure components will remain secure during installation and operation.
- Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause serious eye injury.
- Always use extreme caution when drilling a vehicle. Always disconnect power before welding. Thoroughly inspect the area to be drilled (on both sides of material when possible) prior to drilling, and relocate any objects that may be damaged.
- Always remove jewelry and wear eye protection.
- Always use extreme caution when jacking up a vehicle for work. Set emergency brake and use tire blocks. Locate and use the vehicle manufacturers designated lifting points. Use jack stands.
- Always use appropriate and adequate care in lifting components into place.
- Always ensure components will remain secure during installation and operation.
- Always wear safety glasses when installing this kit. A drilling operation will cause flying metal chips. Flying chips can cause serious eye injury.
- Always use extreme caution when drilling a vehicle. Always disconnect power before welding. Thoroughly inspect the area to be drilled (on both sides of material when possible) prior to drilling, and relocate any objects that may be damaged.
A message from the owner
Fab Fours’ was born out of a passion for customizing vehicles and a love of the outdoors. Our engineering team uses the latest 3D design software to turn new product ideas into reality. In our factory, designs come to life with the combination of cutting edge technology for metal cutting and forming and an American workforce that puts its’ heart and pride into every product.
From design and manufacturing, to quality and delivery, Fab Fours’ mission is to be the market leader for steel truck and jeep accessories. We make sure a quality product is delivered on time, more than expected, better than expected to our customers.
Enjoy your new Fab Fours product. Welcome to the family!
Greg Higgs
Founder, Fab Fours
Getting started
Before you begin the installation process of your new Fab Fours product, we suggest laying out all materials and parts on a pad or protective surface.
Failure to fully account for all components before beginning installation may leave vehicle immobile until part is acquired. Refer to the next pages as an inventory check.
Provided materials
50307-HW – SLIDER 2DOOR HARDWARE KIT
22555 – DS TUBE SLIDER
50308-HW – PLASTIC TUBE CAP KIT
22556 – PS TUBE SLIDER
Hardware kit | G5252
Fab Fours
Identification
|
Component
Description
|
QTY
---|---|---
50307-HW
|
3/8”-16 – 1.25” YELLOW ZINC HEX HEAD BOLT, GRADE 8
|
8
50307-HW
|
3/8”-16 YELLOW ZINC HEX NUT, GRADE 8
|
8
50307-HW
|
3/8” YELLOW ZINC LOCK WASHER, GRADE 8
|
8
50307-HW
|
3/8” YELLOW ZINC FLAT WASHER, GRADE 8
|
16
50307-HW
|
M10-1.5 X 25 HEX HEAD FLANGE BOLT
|
4
50308-HW
|
PLASTIC TUBE CAPS
|
4
TOOLS REQUIRED
- 9/16” socket and wrench
- 13mm Socket
- 3/8” Drill bit
assistance
We recommend two people perform the installation as items are heavy and may need to be held in place while installing.
Organization
Disassemble the vehicle where you can catalog and store everything. We suggest labeling and bagging all the OEM bolts when removing from the vehicle. Failure to keep track of parts could lead to an inability to properly reinstall components.
assistance
This manual shows the six sensor configuration for illustration purposes but your specific installation may vary.
1. With assistance, hold the sliders up to the pinch seam and use the provided 3/8” zinc bolts with flat/lock washers and nuts to loosely attach it (4 bolts per side). Note: some pinch seam holes may need to be opened up using a 3/8” drill bit. Figure 1.
Figure 1
2. Use the provided M10 bolts with washers to fasten the mounts to the body mounts. Figure 2.
Figure 2
3. Align the sliders as desired and fully tighten all monting hardware.
Contact information
Fab Fours Inc.
2213 Industrial Park Road
Lancaster, SC 29720
Phone: 866-385-1905
Fax: 970-385-1914
Email: [email protected]
“If you’re looking for more of the same, Then you’ve come to the wrong place.”
– Greg Higgs