Zwave PAN28 Smart Touch Wall Switch Instruction Manual

Zwave PAN28 Smart Touch Wall Switch

Product Information

• Product Name: Smart touch wall Switch PAN28

Specifications:

• Operating Voltage: 230Vac/120Vac
• Maximum Load Range: Resistive load
• Operating Temperature: Not specified
• Humidity: Not specified
• Storage Temperature: Not specified
• Location Frequency Range: Not specified
• RF Maximum Power: Not specified
• OTA FCC ID: Not specified
• Dimensions: Not specified
• Wire: Not specified

Product Usage Instructions

1. Safety Precautions and Installation:
   • Avoid installing the unit in storming or raining weather.
   • Switch off power source before installing or maintenance.
   • Ensure the power supply circuit is protected by a 16A circuit breaker or suitable equivalent fuse.
   • Installation must be performed by skilled technicians who are informed about the standards and technical requirements of the appliance and its proper installation.
   • Check local codes as they apply to your situation
   • If the house wiring is of aluminum, consult with an electrician about proper wiring methods.
   • Before proceeding with the installation, TURN OFF THE POWER TO THE LIGHTING CIRCUIT AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL SHOCK.
2. Troubleshooting:
   • The Switch not working and LED off:
   • Check power connections to the main power.
   • Don’t open up the Switch and send it for repair if it’s broken down.
3. Installation Steps:
   • Connect PAN28 to AC N and L.
   • Connect Load to NO1.
4. Adding to Z-WaveTM Network:
   • Press the Include button of PAN28 three times within 2 seconds to enter inclusion mode.
   • The Z-Wave Controller does not allocate a node ID to the Switch.
   • Have Z-Wave Controller entered inclusion mode.
   • To support handling of the device when already installed, the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Note: For more detailed instructions and information, refer to the user manual available at http://www.philio-tech.com.

Introduction

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
There are many kind of application by using the module to switch Load On and Off, one main application is the light control. The new smart relay calibration technology can reduce the inrush current caused by the load and let the module work perfectly with many kind of light like incandescent, fluorescent and LED light.

Safety Precautions and Installation

• Avoid installing the unit in storming or raining weather.
• Be sure to isolate or switch off power source before installing or maintenance.
• Do ensure that the power supply circuit protected by a 16A circuit breaker or suitable equivalent fuse.

IMPORTANT

• Installation must be performed by skilled technicians who are informed about the standards and technical requirements of the appliance and its proper installation.
• Check your local codes as they apply to your situation. If the house wiring is of aluminum, consult with an electrician about proper wiring methods.

Before proceeding with the installation, TURN OFF THE POWER TO THE LIGHTING CIRCUIT AT THE CIRCUIT BREAKER OR FUSE BOX TO AVOID ELECTRICAL SHOCK.

Specification

908.40MHz; 916.00MHz (USA/Canada)

920.90 MHz, 921.70 MHz, 923.10 MHz (Taiwan)

RF Maximum Power| +10dBm (Peak), -10dBm (Average)
OTA| Support
FCC ID| RHHPAN28
Dimensions| 47.5 x 39 x15.6 mm
Wire| 0.75mm², 18AWG

** Specifications are subject to change and improvement without notice.

Troubleshooting

1. The Switch is not connect to the Main power
2. The Switch break down

|

1. Check power connections
2. Don’t open up the Switch and send it for repair.

The Switch LED illuminating, but cannot control the ON/OFF

Switch of the attached load

| Check if the load connect into the Switch has its own ON/OFF switch| Set the ON/OFF switch of the attached load to ON
---|---|---
The Switch LED illuminating, but the detector cannot control the Switch|

1. Not carry out association
2. Same frequency interference

|

1. Carry out association
2. Wait for a while to re-try

LED keep flashing continuously, but cannot

control

| Overload occurs| Remove the attached load or check max. load cannot exceed 85°C (230Vac/120Vac) (Resistive load)

Installation Steps

1. Connect PAN28 to AC N and L.
2. Connect Load to NO1.

Fig 1. Assembling and wiring

For Instruction to http://www.philio-tech.com

DANGER
Danger of electrocution!

All works on the device may be performed only by a qualified and licensed electrician. Observe national regulations.
Any works introducing changes into the configuration must be always performed with disconnected voltage.

Choosing a Suitable Location

1. Do not locate the Module facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the Module is 0°C~40°C.
3. Do not locate the Module where exists combustible substances or any source of heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of Module will become a little bit hot of which phenomenon is normal.

Adding to Z-WaveTM Network
In the front casing, there is an on/off button with LED indicator below which is used to toggle switch on and off. The table below lists an operation summary of basic Z-Wave functions. Please refer to the instructions for your Z-WaveTM Certificated Primary Controller to access the Setup function, and to include/exclude/reset devices

2-second on, 2-second off
Add (Inclusion)| Have Z-Wave Controller entered inclusion mode.| One press one flash

※ To support handling of the device when already installed the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Pressing Include button of PAN28 three times within 2 seconds will enter inclusion mode.

SmartStart|

1. To initiate the SmartSart process, please type in the first five digits of DSK string or scan the QR code. The QR Code can be found on PAN28 or in the box. Ex: DSK: 18112-24021-58001-62259- 57092- 27453-08187-47408
2. PAN28 is supported with SmartStart, it can be added to Z-Wave™ network by scanning the Z-Wave™ QR code on the product.
3. Without further actions, PAN28 will be automatically included in a certified Z- Wave™ Controller with SmartStart inclusion ability in 10 minutes after it turned on.

|
---|---|---
Remove (Exclusion)| Have Z-Wave Controller entered exclusion mode.| One press one flash

※ To support handling of the device when already installed the external switch can be used for inclusion or exclusion for 3 minutes after power up.

Pressing Include button of PAN28 three times within 2 seconds will enter exclusion mode.
Node ID has been excluded.| 2s On, 2s Off (No node ID)
Reset| Pressing Include button of PAN28 three times within 2 seconds will enter

inclusion mode.

| One press one flash
 | Within 1 second, press Include button of

PAN28 again for 5 seconds.

|
---|---|---
IDs are excluded.| 2s On, 2s Off (No node ID)

• Adding a node ID allocated by Z-Wave Controller means inclusion. Removing a node ID allocated by Z-Wave Controller means exclusion.
• Failed or success in including/excluding the node ID can be viewed from the Z-Wave Controller.
• Sometimes people are not easy to execute exclusion or inclusion especially when PAN28 already installed in a wall box. To solve this issue, PAN28 support a special feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association” at the first 3 minutes when first time connect to main power.

LED Indication
There is a LED for identify function in the front case. PAN28 support the indicator ID 0x50 (Identify) and Properties ID 0x03, 0x04 and 0x05.
To distinguish what mode the switch is in, view from the LED for identification.

LED will lights off.
No node ID| Under normal operation, when the Switch has not been allocated a node ID, the LED flashes on and off alternately at 2-second intervals.
Overload| When overload state occurs, the Switch is disabled of which LED flashes on and off alternately at 0.2 second intervals. Overload state can be cleared by disconnect and reconnect the Switch to the main power.

Installation

1. Put the in wall switch into a wall box and connect the AC power wire L, N to PAN28 connector L, N.
2. Connect the wall switch to the PAN28 as Fig1.
3. There are 3 mode PAN28 can be configured to match different kind of wall switch, please refer to 3-1 External switch mode which described in next section of this user manual
4. If Edge-Toggle mode has been set, and the S1/S2 is connect to normal bi-stable switch, every time when change the state of the wall switch will also swap the state of Relay1.

Programming

1. Basic Command Class / Binary Switch Command Class

The Switch will respond to BASIC and BINARY commands that are part of the Z-Wave system.

BASIC_GET / BINARY_SWITCH_GET
PAN28 has three relays, it will report ON when any relay is ON, or report OFF when relay 1、relay2 and relay3 are all OFF.

• Basic Get Command: [Command Class Basic, Basic Get]

Basic Report Command:

• Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)] Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]

Binary Switch Get Command:[Command Class Switch Binary, Switch Binary Get]

Binary Switch Report Command:

• Report OFF:[Command Class Switch Binary, Switch Binary Report, Value =0(0x00)]
• Report ON:[Command Class Switch Binary, Switch Binary Report, Value = 255(0xFF)]

BASIC_SET / SWITCH_BINARY_SET
PAN28 will turn on or off all the three relays upon receipt of the following commands from a Z-Wave Controller.

[Command Class Basic, Basic Set, Value = 1~99, 255(0xFF)]: all the loads attached to the Switch turns on.
[Command Class Basic, Basic Set, Value = 0(0x00)]: all the loads attached the Switch turns off.

the loads attached to the Switch turns on.
[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: all the loads attached to the Switch turns off.

Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to the associated Z-Wave devices. It supports four groups and every group has five nodes support.
Group1 is called Lifeline which support SWITCH_BINARY_REPORT、 NOTIFICATION_REPORT、 DEVICE_RESET_LOCALLY_NOTIFICATION and INDICATOR_REPORT.

• For group 2, the Switch will report ON/OFF status of Relay1
• For group 3, the Switch will report ON/OFF status of Relay2
• For group 4, the Switch will report ON/OFF status of Relay3

1. Auto report to Grouping 1(Maximum Node 5)
2. On/Off Event Report
   When “on” or “off” state of any relay has been changed, it will send Binary Switch
   Report to the nodes of Group1. It will report ON when any relay is ON, or report OFF when relay 1、relay2 and relay3 are all OFF.

Binary Switch Report
ON:[Command Class Switch Binary, Switch Binary Report, Value =255(0xFF)] OFF:[Command Class Switch Binary, Switch Binary Report, Value =0(0x00)]

Overload Notification report command
When PAN28 detect the overload, it will send Notification Report to Group1.

The content of Notification Report

Notification report command:[Command Class Notification, Notification Report,
Notification Type = 0x08, Event state = 0x08]

Z-Wave’s Configuration

Configuration Paramete

r

| Function| Size (Byte)| Value| Unit| Default| Description
---|---|---|---|---|---|---
1| LED

brightness level

| 1| 0-100|  | 100| 0 : LED always off 1~100 : 1%~ 100 %
2| LED color for| 1| 0-3|  | 1| 0 : LED off
 | relay on|  |  |  | 1 : Green
 | indication|  |  |  | 2 : Red

3  : Yellow

3| LED color for| 1| 0-3|  | 2| 0 : LED off
 | relay off|  |  |  | 1 : Green
 | indication|  |  |  | 2 : Red

3  : Yellow

4| All on / All off

function option

| 1| 0-1|  | 1| 0：Disable

1：Enable

5| Delay time to turn off the

Specific Relays

| 1| 0-255| 1

min

| 1| 0 : Disable

1-255 : 1min ~255min

6| Specified relays| 1| 1-7|  | 1| 1 :

Relay1+Relay2+Relay3 2 : Relay1+Relay2

 |  |  |  |  | 3 : Relay2+Relay3
 |  |  |  |  | 4 : Relay1+Relay3
 |  |  |  |  | 5 : Relay1
 |  |  |  |  | 6 : Relay2
 |  |  |  |  | 7 : Relay3
7| Restore switch state mode| 1| 0-2|  | 1| 0 : Switch off

1 : Last switch state 2 : Switch on

1. LED brightness level：
   The led brightness level can be set as off or from 1% to 100%. The default setting is 100%.

2. LED color for relay on indication：
   The led color for relay on indication can be set as LED OFF、Green、Red or Yellow. The default setting is Green.

3. LED color for relay on indication：
   The led color for relay off indication can be set as LED OFF、Green、Red or Yellow. The default setting is Red.

4. All on/ All off function option：
   The All on/All off function can be disable or enable. The default setting is Enable.

5. Delay time to turn off the specified relays：
   If user press the 5th touch key once, it will turn on all the specified relays and after a delay time passed turn them off. This is helpful for user don’t have to touch the dark to leave. The default setting is 1 min.

6. Specified relays：
   This setting is used for configuration parameter 5. To specify the relays for the delay off function. The default setting select relay1 and relay2 and relay3.

7. Restore switch state mode
   Whenever the AC power return from lost, PAN28 will restore the switch state which could be SWITCH OFF、LAST SWITCH STATE、SWITCH ON. The default setting is LAST SWITCH STATE.

Firmware update over the air (OTA)
PAN28 is based on 800 series SoC and supports Firmware Update Command Class, it can receives the updated firmware image sent by controller via the Z-wave RF media. It is a helpful and convenient way to improve some function if needed.

Command Classes
The Switch supports Command Classes including…

Disposal

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. Philio Technology Corporation
8F.,No.653-2,Zhongzheng Rd., Xinzhuang Dist., New Taipei City 24257,Taiwan(R.O.C)
www.philio-tech.com

FCC Interference Statement
This equipment has been tested and found to comply with the limit’s for a Class B digital de-vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gener-ates, uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the in-terference by one of the following measures:

• Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.
  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

References

• philio-tech.com
• philio-tech.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>