Injen PF8056 Tuned Air Intake System Instruction Manual
- June 13, 2024
- Injen
Table of Contents
Injen PF8056 Tuned Air Intake System
Product Information
Product Name: GHI C
Instruction Manual Part Number: PF8056
Vehicle Application:
- Make: RAM
- Model: 1500
- Year: 2019-2020
- Engine: 5.7L V8 HEMI
- Excludes eTorque models
Features:
- The World’s First Tuned Air Intake System!
- Factory-safe air/fuel ratios for Optimum performance
- Injens tuning process covered by three U.S. Patents
Components:
| Item | Quantity | Part Number | Description |
|---|---|---|---|
| A | 1 | W-PF8056 | Intake Tube |
| B | 1 | #11172 | Heatshield |
| C | 1 | #1111BB | 4 Dry Air filter |
| F | 2 | #4005 #56 | clamps |
| G | 1 | #6020 | M6 Vibra-mount |
| H | 2 | #6002 | M6 nuts |
| I | 1 | #6010 | Fender washer |
| J | 1 | #14062 | machined fitting |
| K | 2 | #4007 #10 | clamps |
| L | 1 | #6023 | Vinyl trim @ 9.5 L |
| M | 1 | #6058 | Rubber trim @ 21 L |
| N | 1 | #3217 | 17mm hose @ 12 L |
Product Usage Instructions
WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE MAY DAMAGE THE INTAKE SYSTEM, ENGINE AND COMPONENTS!!! *Do not attempt to install the intake system while the engine is hot. Severe burns could result from touching hot engine components!
TOOLS REQUIRED: E, B
NOTE: Verify your filter before any cleaning maintenance! Blue media filter: Dry Air Filter, no oil required. (SuperNano Web Dry filters require no oil, these can be cleaned using a vacuum or light-compressed air. Please do not clean using water or injure the restore kit.) Red media filter: Factory Oiled Air Filter. (Oiled cotton gauze filters require oil, please use the Injen restore kit. This filter can use water or a cleaning solution for maintenance.) Please visit injen.com for filter cleaning instructions.
NOTE: DISCONNECT BATTERY BEFORE INSTALLATION
- The stock intake system is shown. Temp. sensor
- Disconnect the Temperature sensor harness.
- Loosen the clamp on the throttle body using an 8mm nut driver.
- Lift up and remove the air box assembly from the vehicle.
- Pull back the intake tube from the throttle body.
- Carefully lift up and remove the front plastic scoop.
- Install the provided 2 6014 grommets to the holes on the heatshield.
- Install the provided Vinyl trim to the side of the heatshield.
- Install the Rubber trim to the top of the heatshield.
The World’s First Tuned Air Intake System.
Factory safe air/fuel ratios for Optimum performance Injens tuning process
covered by three U.S. Patents
Vehicle Application
- Make: RAM
- Model: 1500
- Year: 2019-2020
- Engine: 5.7L V8 HEMI
- Excludes eTorque models
OVERVIEW
| Item | QTY. | P/N | Discription |
|---|---|---|---|
| A | 1 | W-PF8056 | Intake Tube |
| B | 1 | #11172 | Heatshield |
| C | 1 | #1111BB | 4” Dry Air filter |
| D | 1 | #M-20119 | 3.50” 90° elbow hose w/ sensor grommet |
| E | 2 | #6014 | Grommets for heatshield |
| F | 2 | #4005 | #56 clamps |
| G | 1 | #6020 | M6 Vibra-mount |
| H | 2 | #6002 | M6 nuts |
| I | 1 | #6010 | Fender washer |
| J | 1 | #14062 | machined fitting |
| K | 2 | #4007 | #10 clamps |
| L | 1 | #6023 | Vinyl trim @ 9.5” L |
| M | 1 | #6058 | Rubber trim @ 21” L |
| N | 1 | #3217 | 17mm hose @ 12” L |
TOOLS REQUIRED
- 10mm Ratchet & Socket
- 8mm nut drive
- Flat Head Screwdriver
- WARNING: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PRO-VIDED HARDWARE MAY DAMAGE THE INTAKE SYSTEM, ENGINE AND COMPONENTS!!!
- Do not attempt to install the intake system while the engine is hot.
- Severe burns could result from touching hot engine components!
- Report any defective or missing parts to the authorized Injen dealer you purchased this product. Before installing any parts of this system, please read the instructions thoroughly.
- If you have any questions regarding installation, please contact your Injen Technology dealer. Installation DOES require some mechanical skills. A qualified mechanic is always recommended.
- A Limited Lifetime Warranty to the original purchaser against defects in material and workmanship on all Injen intake systems excluding the filter element. Any and all warranty coverage is limited to the repair or replacement of the defective part only, at Injen Technology’s discretion.
- The warranty does not cover incidental or consequential damages, nor does it cover the cost of installation or removal of the defective part or its replacement. Proof of purchase is required.
- Injen intake systems are street legal in most states unless the state is adopting California Emissions standards. States that have adopted California emission standards include: Arizona, California, Connecticut, the District of Columbia, Maine, Maryland, Massachusetts, New Jersey, New
- Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont, and Washington. These states will require a California Air Resource Board Executive Order Number (CARB E.O.) for the legal use of an Injen intake system in your vehicle for use on public roads or highways. This vehicle will be considered “Legal in California only for racing vehicles competition use only, which may never be used upon a public street or highway. Please keep your factory air box assembly for any future use.
- NOTE: Verify your filter before any cleaning maintenance!
- Blue media filter: Dry Air Filter, no oil required.
- (SuperNano Web Dry filters require no oil, these can be cleaned using a vacuum or light-compressed air.
- Please do not clean using water or injure the restore kit. )
- Red media filter: Factory Oiled Air Filter.
- (Oiled cotton gauze filters require oil, please use the Injen restore kit.
- This filter can use water or a cleaning solution for maintenance. )
- Please visit injen.com for filter cleaning instructions.
NOTE: DISCONNECT BATTERY BEFORE INSTALLATION
INSTALLATION INSTRUCTION
- Stock intake system shown.
- Disconnect the Temperature sensor harness.
- Loosen the clamp on the throttle body using 8mm nut driver.
- Lift up and remove the air box assembly out of the vehicle.
- Pull back the intake tube from the throttle body.
- Carefully lift up and remove the front plastic scoop
- Install the provided 2 6014 grommets to the holes on the heatshield.
- Install the provided Vinyl trim to the side of the heatshield.
- Install the Rubber trim to the top of the heatshield.
- Install the heatshield assembly into the vehicle. position the tabs with grommets to the factory plastic studs.
- Secure the bracket to the hole on the plastic wheel cover.
- Secure the bracket using the provided M6 vibramount and M6 nut under plastic.
- This will be used for the intake tube.
- With a flat head screwdriver, carefully turn and remove the temperature sensor from the OEM intake tube.
- Install the temperature sensor grommet into the hole on the elbow hose. attach the clamps to the elbow hose.
- Install the elbow hose assembly to the throttle body. Do not tighten.
- Now install the crankcase line to the OEM plastic crankcase line from step 7. Make sure you hear a click.
- Install the intake tube and position the bracket to the vibramount and to the elbow hose. Do not tighten.
- Position for best fit, Secure and tighten backet using provided M6 nut and fender washer.
- Secure the crankcase line to the fitting on the intake tube. Tighten both clamps using 8mm nut driver.
- Install the filter to the intake tube.
- Adjust for fitment. Tighten all clamps. RE-adjust in necessary and make sure there is proper clearance.
- Re-connect the temperature sensor harness.
- Congratulations! You have just completed the installation of this intake system. Periodically, check the alignment of the intake, normal wear and tear can cause nuts and bolts to come loose.
- Note: Check clearance and adjust if needed! Failure to check the alignment and adjust the intake can cause damage that will void the warranty. Injen Technology is not responsible for any damages caused by/from improper installation.
Test Drive:
- With the transmission in neutral or park and the parking brake engaged, start the engine. Listen for air leaks or odd noises. If air leaks are detected, secure hoses and connections. For any odd noises, inspect the entire system for cause and adjust intake as needed. The Injen intake will function identically to the factory system but will be louder and more powerful.
- Perform a road test. Listen for odd noises or rattles and fix them as necessary.
- If there are no issues, continue to enjoy your added performance from the Injen performance Intake kit.
- Injen Technology recommends you periodically check clearance and adjust if needed! Failure to check the alignment and adjust the intake can cause damage that will void the warranty. Injen Technology is not responsible for any damages caused by/from improper installation.
- Upon completion of the installation, reconnect the negative battery terminal before you start the engine.
- Align the entire intake system for the best possible fit. Once the intake has been properly fitted continue to tighten all nuts, bolts and clamps.
- Periodically, recheck the alignment of the intake system and make sure there is proper clearance around and along the length of the intake. Failure to follow proper maintenance procedures may cause damage to the intake and will void the warranty.
- Start the engine and listen carefully for any odd noises, rattles and/or air leaks prior to taking it for a test drive. If any problems arise go back and check the vacuum lines, hoses and clamps that maybe causing leaks or rattles and correct the problem.
- Check the filter for excessive dirt build-up. Clean or replace the filter with an original Injen filter (which can be bought online at “injenonline.com”). Congratulations! You have just completed the installation of the best intake system sold on the market. Enjoy the added power and performance of your new intake system.
244 Pioneer Place Pomona California 91768 U.S.A Office:909-839-0706 FAX: (909)839-0427 Email: Tech@injen.com WWW.INJEN.COM
References
- Injen Technology
- Injen Technology
- Automotive Ecommerce Software & Shopping Cart Platform Web Shop Manager
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>