INJEN TECHNOLOGY EVO5009 Evolution Cold Air Intake System Instruction Manual
- June 13, 2024
- Injen Technology
Table of Contents
EVOLUTION COLD AIR INTAKE SYSTEM
Part Number: EVO5009 / EVO5009C
Installation Instructions
| YEAR | MAKE | MODEL | ENGINE |
|---|---|---|---|
| 2012-2018 | JEEP | WRANGLER (JK) | V6-3.6L |
PARTS INCLUDED
| ITEM | QTY | PART NO. | DESCRIPTION |
|---|---|---|---|
| A | 1 | X-15205 | AIRBOX |
| B | 1 | X-15206 | TUBE |
| C | 1 | X-15139 | CLEAR WINDOW |
| D | 2 | X-6109 | PUSH ON RETAINING RINGS |
| E | 1 | X-3236 | 3.125″-3.50″ STEPPING HUMP HOSE |
| F | 1 | X-4004 | SAE 048 CLAMP |
| G | 1 | X-4005 | SAE 056 CLAMP |
| H | 1 | X-15097 | AIR TEMP SENSOR ADAPTER |
| I | 1 | X-1108 | TWIST LOCK FILTER |
| J | 1 | X-11114 | AIR BOX SHIELD AIR DIRECTOR |
| K | 2 | X-6073 | M6 x 20 S.S. Button Head Bolt |
| L | 2 | X-8014 | BLACK ZIP TIES |
| M | 2 | X-6047 | M4 X 0.7 X 10 BUTTON HEAD SCREW |
RECOMMENDED TOOLS
| Ratcheting Wrench | 8mm Nut Driver | Needle Nose Pliers |
|---|---|---|
| 10mm Socket | 2mm Allen Key | Phillips Head Screwdriver |
BEFORE YOU BEGIN
Please check the list of parts included and report any defective or missing
parts to the authorized Injen dealer you purchased this product from. Before
installing any parts of this system, please read the instructions thoroughly.
If you have any questions regarding installation, please contact your Injen
Technology dealer. Installation DOES require some mechanical skills. A
qualified mechanic is always recommended.
This product includes a Limited Lifetime Warranty to the original purchaser
against defects in material and workmanship on all Injen intake systems
excluding the filter element. Any and all warranty coverage is limited to the
repair or replacement of the defective part only, at Injen Technology’s
discretion. The warranty does not cover incidental or consequential damages,
nor does it cover the cost of installation or removal of the defective part or
its replacement. Proof of purchase is required.
Do not attempt to install the intake system while the engine is hot. Severe
burn could result from touching hot engine components.
WARNING: Failure to follow installation instructions and not using the
provided hardware may damage the intake system, engine, or components of
either.
CARB Note: Injen intake systems are street legal in most states unless the
state is adopting to California Emissions standards.
States that have adopted California emission standards include: Arizona,
California, Connecticut, District of Columbia, Maine, Maryland, Massachusetts,
New Jersey, New Mexico, New York, Oregon, Pennsylvania, Rhode Island, Vermont,
and Washington.
These states will require a California Air Resource Board Executive Order
Number (CARB E.O.) for the legal use of an Injen intake system in your vehicle
for use on public roads or highways. Otherwise, the vehicle will be considered
“Legal in California only for racing vehicles competition use only, which may
never be used upon a public street or highway.” Please keep your factory air
intake system for any future on-road use.
Note: It is always recommended to disconnect your battery before
disconnecting any sensors.
FILTER MAINTENANCE
SuperNano-Web Dry Air Filter (Blue Media)
Do not use water or filter oil to clean!
You can use a vacuum cleaner or compressed air to clean.
If you’re using a vacuum cleaner, follow the direction of the pleats on the
outside of the filter element.
If you’re using compressed air, make sure it never exceeds 25 PSI. Use a
blower from the inside of the element towards the outside, following the
direction of the pleats.
8-Layer Oiled Cotton Gauze Air Filter (Red Media)
Injen Technology’s Oiled Filter Restore Kit (P/N: X-1030) is recommended for
cleaning and maintenance.
Use the cleaning solution or water to wash out the filter element, then use
Injen’s Proprietary Filter Oil to re-oil the element. The amount of oil to use
in grams is provided on the product page for the filter at
https://injen.com. Let sit for 24 hrs for the oil to completely saturate the
cotton gauze media.
CONGRATULATIONS! You have just completed the installation of this intake
system. Periodically, check the alignment of the intake, normal wear and tear
can cause nuts and bolts to come loose.
Note: Check clearance and adjust if needed! Failure to check the
alignment and adjust the intake can cause damage that will void the warranty.
Injen Technology is not responsible for any damages caused by/from improper
installation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>